Update README.md

V1.11 - Adding a Boost mode
Allows users to enable a boost mode. This allows you to hold down the button near the tip while soldering to temporarily boost the soldering temperature. Closes #10
2025-02-26 07:53:55 +00:00 · 2017-07-08 23:26:41 +10:00 · 2017-07-08 23:16:02 +10:00 · 2017-07-08 22:36:49 +10:00 · 2017-07-08 18:12:28 +10:00 · 2017-07-07 23:22:20 +10:00
34 changed files with 3588 additions and 942 deletions
--- a/.gitignore
+++ b/.gitignore
@@ -27,7 +27,7 @@
 *.app
 *.i*86
 *.x86_64
-*.hex
+workspace/*.hex

 # Debug files
 *.dSYM/
@@ -36,3 +36,4 @@ workspace/ts100/Debug/*
 workspace/.metadata/*

 workspace/ts100/.settings/language.settings.xml
+workspace/ts100/.cproject
--- a/Backup.hex
+++ b/Backup.hex
--- a/README.md
+++ b/README.md
@@ -1,21 +1,113 @@
 # TS100
-This is a complete open source re-write of the software for the ts100 soldering iron sold by minidso
+This is a complete re-write of the open source software for the ts100 soldering iron.
+This project is feature complete for use as a soldering iron, but is still open to ideas and suggestions.

-This was started to remove the need for usb for changing system settings.
+This project was started to remove the need for USB for changing system settings.
+In the latest official firmware they have also added a settings menu system, so it is still worth comparing the two firmwares to select your preferred option.

-The software has similar functionality to the original firmware.
-
-# Features Working
+## Features
 * Soldering / Temperature control
-* Full PID Iron Temp
-* Adjusting temperature
-* Automatic sleep
+* Full PID iron temperature control
+* Automatic sleep with selectable sensitivity
 * Motion wake support
-* Basic settings menu
+* Settings menu
+* Input voltage UVLO measurement for battery powered use
+* All settings saved
+* Improved readability Fonts
+* Use hardware features to improve reliability
+* Can disable movement detection if desired
+* Calibration of the temperature offset
+* Boost mode lets you temporarily change the temperature when soldering

-# Features still to be implimented
-* Input voltage UVLO measurement
-* Saving settings to flash for persistance
-* Improved GUI
-* Manual Temp Calibration
-* Use hardware I2C
+# Upgrading your ts100 iron
+This is completely safe, if it goes wrong just put the .hex file from the official website onto the unit and your back to the old firmware. Downloads for the hex files to flash are available on the [releases page.](https://github.com/Ralim/ts100/releases)
+Officially the bootloader on the iron only works under windows. However, users have reported that it does work under Mac, and can be made to work under Linux. Details over on the [wiki page](https://github.com/Ralim/ts100/wiki/Upgrading-Firmware).
+
+1. Hold the button closest to the tip, and plug in the USB to the computer.
+2. The unit will appear as a USB drive.
+3. Drag the .hex file onto the USB drive.
+4. The unit will disconnect and reconnect.
+5. The filename will have changed to end in .RDY or .ERR 
+6. If it ends with .RDY you're done! Otherwise something went wrong.
+7. Disconnect the USB and power up the iron. You're good to go.
+
+For the more adventurerous out there, you can also load this firmware onto the device using a SWD programmer.
+On the bottom of the MCU riser pcb, there are 4 pads for programming.
+There is a complete device flash backup included in this repository. (Note this includes the bootloader, so will need a SWD programmer to load onto the unit). Please do not use the backup of the bootloader for anything malicious, its only saved here for those who are tinkering with their iron and decide to replace it.
+
+# New Menu System
+This new firmware uses a new menu system to allow access to the settings on the device.
+When on the main screen, the unit shows prompts for the two most common operations.
+-> Pressing the button near the tip enters soldering mode
+-> Pressing the button near the power input enters the settings menu.
+-> Pressing both buttons together enters the Extras menu
+## Soldering mode
+In this mode the iron works as you would expect, pressing either button will take you to a temperature change screen. Use each button to go up and down in temperature. Pressing both buttons will exit you from the temperature menu (or wait 3 seconds and it will time out).
+Pressing both buttons will also exit the soldering mode.
+
+## Settings Menu
+This menu allows you to cycle through all the options and set their values.
+The button near the tip cycles through the options, and the one near the usb changes the selected option.
+Note that settings are not saved until you exit the menu, and some settings such as screen flip do not apply until a power cycle is applied.
+If you leave the unit alone (ie don't press any buttons) on a setting, after 3 seconds the screen will scroll a longer version of the name
+
+* UVCO -> Undervoltage cut out level, settable in 1V increments from 10-24V
+* STMP -> The temperature the unit drops to in sleep mode
+* SLTME -> Sleep time, how long it takes before the unit goes to sleep
+* SHTME -> Shutdown Time, how long the unit will wait after movement before shutting down completely
+* MOTION -> Wether motion detection is enabled or not
+* SENSE -> Motion Sensitivity, H is more sensitive. L is lowest sensitivity (ie takes more movement to trigger)
+* TMPUNIT -> Temperature unit, C or F
+* TMPRND -> Temperature Rounding, {1,5,10}
+* TMPSPD -> How fast the temperature should update in the soldering status screen.
+* FLPDSP -> Flip display for left handed users
+* BOOST -> Enable boost mode
+* BTMP -> Set the temperature for the boost mode
+
+Temperature rounding means that the unit will round off the temperature before displaying. This can helpt to reduce the flickering of the temperature when the unit oscillates between two temperatures.
+## Extras Menu
+This menu defaults to showing the current temperature on the tip. 
+Pressing the button near the iron tip will show the current input voltage. Pressing the other button while this is show will allow you to calibrate the reading if your iron is like mine and is not overly accurate out of the factory. (Press buttons to change measurement up and down, press both to exit and save). 
+
+Pressing the button near the usb enters the temperature offset setting menu, when the iron is cold, pressing the other button will start the unit calibrating for any offset in the tip temperature.
+## Boost mode
+This allows you to change the front key (one near the tip) to become a boost button instead of going to temperature editing when in soldering mode. This allows you to set this button to change the soldering temperature for short periods. For example when soldering a big joint and you want to boost the temperature a bit.
+
+The boost temperature is set in the settings menu.
+# Version Changes:
+V1.11
+- Boost mode
+
+V1.10
+- Adds help text to settings
+- Improves settings for the display update rate
+
+V1.09
+- Adds display modes, for slowing down or simplifying the display
+
+V1.08
+- Fix settings menu not showing flip display
+
+V1.07
+- Adds shutdown time to automatically shutdown the iron after inactivity
+
+V1.06
+- Changes H and C when the iron is heating to the minidso chevron like images
+
+V1.05
+- Adds ability to calibrate the input voltage measurement
+
+V1.04
+- Increased accuracy of the temperature control
+- Improved PID response slightly
+- Allows temperature offset calibration
+- Nicer idle screen
+
+V1.03 
+- Improved Button handling
+- Ability to set motion sensitivity
+- DC voltmeter page shows input voltage
+
+V1.02
+- Adds hold both buttons on IDLE to access the therometer mode.
+- Changes the exit soldering mode to be holding both buttons (Like original firmware).
--- a/SystemDesign.md
+++ b/SystemDesign.md
@@ -1,21 +0,0 @@
-# System Design
-
-# Movement Detection
-The unit has a MMA8652FC Accelerometer on the small sub board along with the STM32.
-This is used for motion detection of the soldering iron.
-
-# USB Disk
-When the unit is plugged into the computer, it presents a FAT device to the operating system over the usb connection.
-This is implemented using a ram buffer for the disk.
-
-
-
-
-# Future improvements to be made
-These features are things I would like to add to the firmware
-
-* Use the sysTick hardware for timing of events
-* Move all the settings to an on device menu system instead of usb link
-* Move error codes into a unified struct
-* Rewrite most of the OLED stack to not require hardcoded values
-* Rework the modes of the unit to be neater
--- a/V1.0.pdf
+++ b/V1.0.pdf
--- a/TS100.png
+++ b/TS100.png
--- a/VERSION.txt
+++ b/VERSION.txt
@@ -1,25 +0,0 @@
-v2.11 update (2015/08/03)
-1, optimizing the key for delay;
-2, optimized display processing
-3, optimization of high-temperature alarm;
-4, to increase the maximum voltage alarm;
-5, the newly added screen protection, enter standby interface for some time, the screen will shut itself down, or move the iron screen button will automatically light up;
-6, optimizing the movement decision
-
-v2.10 update (2015/07/14)
-1, temperature calibration is not refresh bug;
-2, Cancel USB-powered thermometer into the function;
-
---Original --
-v2.11 <20><><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>(20150803)
-1<EFBFBD><EFBFBD>	<09>Ż<EFBFBD><C5BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ʱ<EFBFBD><CAB1><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
-2<EFBFBD><EFBFBD>	<09>Ż<EFBFBD><C5BB><EFBFBD>ʾ<EFBFBD><CABE><EFBFBD><EFBFBD>
-3<EFBFBD><EFBFBD>	<09>Ż<EFBFBD><C5BB><EFBFBD><EFBFBD>±<EFBFBD><C2B1><EFBFBD><EFBFBD><EFBFBD>
-4<EFBFBD><EFBFBD>	<09><><EFBFBD>߱<EFBFBD><DFB1><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ߵ<EFBFBD>ѹ<EFBFBD><D1B9>
-5<EFBFBD><EFBFBD>	<09>¼<EFBFBD><C2BC><EFBFBD><EFBFBD><EFBFBD>Ļ<EFBFBD><C4BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ܣ<EFBFBD><DCA3><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>һ<EFBFBD><D2BB>ʱ<EFBFBD><CAB1><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Ļ<EFBFBD><C4BB><EFBFBD>Լ<EFBFBD><D4BC>رգ<D8B1><D5A3><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ƶ<EFBFBD><C6B6><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Ļ<EFBFBD><C4BB><EFBFBD>Զ<EFBFBD><D4B6><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
-6<EFBFBD><EFBFBD>	<09>Ż<EFBFBD><C5BB>ƶ<EFBFBD><C6B6>ж<EFBFBD>
-
-v2.10 <20><><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>(20150714)
-1<EFBFBD><EFBFBD>	<09>¶<EFBFBD>У׼ʱû<CAB1><C3BB>ˢ<EFBFBD>µ<EFBFBD>bug<75><67>
-2<EFBFBD><EFBFBD>	ȡ<><C8A1>USB<53><42><EFBFBD><EFBFBD>ʱ<EFBFBD><CAB1><EFBFBD><EFBFBD><EFBFBD>¶ȼƵĹ<C6B5><C4B9>ܣ<EFBFBD>
-
--- a/workspace/ts100/.cproject
+++ b/workspace/ts100/.cproject
@@ -14,7 +14,7 @@
 				</extensions>
 			</storageModule>
 			<storageModule moduleId="cdtBuildSystem" version="4.0.0">
-				<configuration artifactExtension="elf" artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.debug" cleanCommand="rm -rf" description="" id="fr.ac6.managedbuild.config.gnu.cross.exe.debug.1236130657" name="Debug" parent="fr.ac6.managedbuild.config.gnu.cross.exe.debug" postannouncebuildStep="Generating binary and Printing size information:" postbuildStep="arm-none-eabi-objcopy -O binary &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.bin&quot;; arm-none-eabi-size &quot;${BuildArtifactFileName}&quot; ">
+				<configuration artifactExtension="elf" artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.debug" cleanCommand="rm -rf" description="" id="fr.ac6.managedbuild.config.gnu.cross.exe.debug.1236130657" name="Debug" parent="fr.ac6.managedbuild.config.gnu.cross.exe.debug" postannouncebuildStep="Generating binary and Printing size information:" postbuildStep="arm-none-eabi-objcopy -O binary &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.bin&quot;; arm-none-eabi-size &quot;${BuildArtifactFileName}&quot; ;arm-none-eabi-objcopy -O ihex &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.hex&quot;">
 					<folderInfo id="fr.ac6.managedbuild.config.gnu.cross.exe.debug.1236130657." name="/" resourcePath="">
 						<toolChain id="fr.ac6.managedbuild.toolchain.gnu.cross.exe.debug.2123758208" name="Ac6 STM32 MCU GCC" superClass="fr.ac6.managedbuild.toolchain.gnu.cross.exe.debug">
 							<option id="fr.ac6.managedbuild.option.gnu.cross.mcu.1416828544" name="Mcu" superClass="fr.ac6.managedbuild.option.gnu.cross.mcu" value="STM32F103T8Ux" valueType="string"/>
@@ -69,10 +69,10 @@
 							<tool id="fr.ac6.managedbuild.tool.gnu.archiver.1926145385" name="MCU GCC Archiver" superClass="fr.ac6.managedbuild.tool.gnu.archiver"/>
 							<tool id="fr.ac6.managedbuild.tool.gnu.cross.assembler.104990963" name="MCU GCC Assembler" superClass="fr.ac6.managedbuild.tool.gnu.cross.assembler">
 								<option id="gnu.both.asm.option.include.paths.834243276" name="Include paths (-I)" superClass="gnu.both.asm.option.include.paths" valueType="includePath">
-									<listOptionValue builtIn="false" value="/home/ralim/Repo/ts100/workspace/ts100/inc"/>
-									<listOptionValue builtIn="false" value="/home/ralim/Repo/ts100/workspace/ts100/StdPeriph_Driver/inc"/>
-									<listOptionValue builtIn="false" value="/home/ralim/Repo/ts100/workspace/ts100/CMSIS/core"/>
-									<listOptionValue builtIn="false" value="/home/ralim/Repo/ts100/workspace/ts100/CMSIS/device"/>
+									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/inc}&quot;"/>
+									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/StdPeriph_Driver/inc}&quot;"/>
+									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/CMSIS/core}&quot;"/>
+									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/CMSIS/device}&quot;"/>
 								</option>
 								<inputType id="cdt.managedbuild.tool.gnu.assembler.input.1754789872" superClass="cdt.managedbuild.tool.gnu.assembler.input"/>
 								<inputType id="fr.ac6.managedbuild.tool.gnu.cross.assembler.input.610009869" superClass="fr.ac6.managedbuild.tool.gnu.cross.assembler.input"/>
@@ -103,7 +103,7 @@
 				</extensions>
 			</storageModule>
 			<storageModule moduleId="cdtBuildSystem" version="4.0.0">
-				<configuration artifactExtension="elf" artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.release" cleanCommand="rm -rf" description="" id="fr.ac6.managedbuild.config.gnu.cross.exe.release.1113492345" name="Release" parent="fr.ac6.managedbuild.config.gnu.cross.exe.release" postannouncebuildStep="Generating binary and Printing size information:" postbuildStep="arm-none-eabi-objcopy -O binary &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.bin&quot;; arm-none-eabi-size -B &quot;${BuildArtifactFileName}&quot;">
+				<configuration artifactExtension="elf" artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.release" cleanCommand="rm -rf" description="" id="fr.ac6.managedbuild.config.gnu.cross.exe.release.1113492345" name="Release" parent="fr.ac6.managedbuild.config.gnu.cross.exe.release" postannouncebuildStep="Generating binary and Printing size information:" postbuildStep="arm-none-eabi-objcopy -O binary &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.bin&quot;; arm-none-eabi-size -B &quot;${BuildArtifactFileName}&quot;;arm-none-eabi-objcopy -O ihex &quot;${BuildArtifactFileBaseName}.elf&quot; &quot;${BuildArtifactFileBaseName}.hex&quot;">
 					<folderInfo id="fr.ac6.managedbuild.config.gnu.cross.exe.release.1113492345." name="/" resourcePath="">
 						<toolChain id="fr.ac6.managedbuild.toolchain.gnu.cross.exe.release.668479481" name="Ac6 STM32 MCU GCC" superClass="fr.ac6.managedbuild.toolchain.gnu.cross.exe.release">
 							<option id="fr.ac6.managedbuild.option.gnu.cross.mcu.302274410" name="Mcu" superClass="fr.ac6.managedbuild.option.gnu.cross.mcu" value="STM32F103T8Ux" valueType="string"/>
--- a/workspace/ts100/.gitignore
+++ b/workspace/ts100/.gitignore
@@ -1 +1,2 @@
 /Debug/
+/Release/
--- a/workspace/ts100/LinkerScript.ld
+++ b/workspace/ts100/LinkerScript.ld
@@ -62,11 +62,11 @@ _Min_Stack_Size = 0x400; /* required amount of stack */
 MEMORY
 {
  RAM (xrw)		: ORIGIN = 0x20000000, LENGTH = 20K
-  ROM (rx)		: ORIGIN = 0x08000000, LENGTH = 64K
+  ROM (rx)		: ORIGIN = 0x08004000, LENGTH = 47K
  
 }
 /*ROM (rx)		: ORIGIN = 0x08004000, LENGTH = 48K*/
-/*^ The rom is shortened as the last ~10K is used for storing the virtual USB Disk, and the offset at the beginning in the bootloader*/
+/*^ The offset at the beginning in the bootloader, 1K at the end for settings (actually 256 bytes, but leaving room for now)*/
 /* Sections */
 SECTIONS
 {
--- a/workspace/ts100/inc/APP_Version.h
+++ b/workspace/ts100/inc/APP_Version.h
@@ -1,43 +0,0 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. ********************                       
- File Name :      APP_Version.h
- Version :        S100 APP Ver 2.11
- Description:
- Author :         bure & Celery
- Data:            2015/08/03
- History:
- 2015/08/03   ͳһ<CDB3><D2BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
- *******************************************************************************/
-
-#ifndef __VERSION_H
-#define __VERSION_H
-
-#define M_VER              'V','0'
-#define S_VER              '0','1'
-#define OEM_TYPE           "0"
-#define APP_BASE           0x0800C000/*Start address of the virtual disk*/
-
-/*----------------------------------------------------------------------------*/
-#ifdef TYPE_DS201
-#define PRODUCT_INFO   "DS201"
-#define SCH_VER        "1.7B"
-#else
-	#ifdef TYPE_DS202
-		#include "DS202V1_6.h"
-		#define FLASH_PAGE       0x0800
-	#else
-		#ifdef TYPE_DS203
-			#define PRODUCT_INFO     "DS203"
-			#define SCH_VER          "2.70"
-		#else
-			#ifdef TYPE_S100
-				#define PRODUCT_INFO     "TS100"
-				#include "S100V0_1.h"
-			#endif
-		#endif
-	#endif
-#endif
-
-/*----------------------------------------------------------------------------*/
-#define DFU_VER            {M_VER,'.',S_VER,LCD_M, 0}
-#endif /* VERSION_H */
-/*********************************  END OF FILE  ******************************/
--- a/workspace/ts100/inc/Analog.h
+++ b/workspace/ts100/inc/Analog.h
@@ -3,16 +3,18 @@
 *
 *  Created on: 20 Sep 2016
 *      Author: ralim
+ *
+ *      Interface to the ADC's basically
 */

 #ifndef ANALOG_H_
 #define ANALOG_H_
 #include "stm32f10x.h"
-#include "S100V0_1.h"
 #include "Bios.h"
 #include "Interrupt.h"
 extern volatile uint16_t ADC1ConvertedValue[2];

 uint16_t Get_ADC1Value(uint8_t i);
-uint16_t readIronTemp(uint16_t calibration,uint8_t read);
+uint16_t readIronTemp(uint16_t calibration_temp, uint8_t read,uint16_t setPointTemp); //read the iron temp in C X10
+uint16_t readDCVoltage(uint16_t divFactor);/*Get the system voltage X10*/
 #endif /* ANALOG_H_ */
--- a/workspace/ts100/inc/Bios.h
+++ b/workspace/ts100/inc/Bios.h
@@ -7,7 +7,14 @@
 #include "stm32f10x.h"
 #include "S100V0_1.h"/*For pin definitions*/
 #include "Analog.h"/*So that we can attach the DMA to the output array*/
-
+#include "stm32f10x_flash.h"
+#include "stm32f10x_rcc.h"
+#include "stm32f10x_dma.h"
+#include "stm32f10x_adc.h"
+#include "stm32f10x_tim.h"
+#include "stm32f10x_exti.h"
+#include "stm32f10x_iwdg.h"
+#include "misc.h"
 extern volatile uint32_t gHeat_cnt;

 inline void setIronTimer(uint32_t time) {
@@ -34,4 +41,4 @@ void Init_EXTI(void);
 void Start_Watchdog(uint32_t ms);
 void Clear_Watchdog(void);
 #endif
-/********************************* END OF FILE ********************************/
+
--- a/workspace/ts100/inc/Font.h
+++ b/workspace/ts100/inc/Font.h
@@ -3,88 +3,190 @@
 *
 *  Created on: 17 Sep 2016
 *      Author: Ralim
+ *
+ *      ... This file contains the font...
 */

 #ifndef FONT_H_
 #define FONT_H_

-const u8 FONT[]={
-		0x00,0xF0,0xFC,0x0E,0x82,0xC2,0x62,0x1E,0xFC,0xF0,0x00,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x1F,0x11,0x10,0x10,0x1C,0x0F,0x03,0x00,0x00,0x00,0x00,/*0*/
-		0x00,0x08,0x04,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,/*1*/
-		0x00,0x04,0x02,0x02,0x02,0xC6,0xFC,0x78,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x18,0x1C,0x16,0x13,0x11,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,/*2*/
-		0x00,0x02,0x02,0x42,0x42,0x66,0xFE,0x9C,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,/*3*/
-		0x00,0x00,0x80,0xE0,0x30,0x1C,0x06,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x03,0x03,0x02,0x02,0x02,0x02,0x1F,0x1F,0x02,0x02,0x00,0x00,0x00,/*4*/
-		0x00,0x7E,0x7E,0x42,0x42,0x42,0xC2,0x82,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,/*5*/
-		0x00,0xE0,0xF8,0x8C,0x44,0x42,0x42,0xC2,0x82,0x80,0x00,0x00,0x00,0x00,
-		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,/*6*/
-		0x00,0x02,0x02,0x02,0x02,0xC2,0xF2,0x1E,0x06,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x10,0x1C,0x0F,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*7*/
-		0x00,0x38,0x7C,0x66,0xC2,0x82,0xC2,0x66,0x7C,0x3C,0x00,0x00,0x00,0x00,
-		0x00,0x0E,0x0F,0x19,0x10,0x10,0x10,0x19,0x0F,0x0E,0x00,0x00,0x00,0x00,/*8*/
-		0x00,0x78,0x7C,0xC6,0x82,0x82,0x82,0x46,0xFC,0xF8,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x10,0x10,0x10,0x10,0x08,0x0C,0x07,0x03,0x00,0x00,0x00,0x00,/*9*/
-		0x00,0x00,0x80,0xF0,0x1E,0x02,0x1E,0xF0,0x80,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1C,0x0F,0x03,0x02,0x02,0x02,0x03,0x0F,0x1C,0x00,0x00,0x00,0x00,/*A*/
-		0x00,0xFE,0xFE,0x42,0x42,0x42,0xE6,0xBE,0x9C,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,/*B*/
-		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x08,0x00,0x00,0x00,0x00,0x00,/*C*/
-		0x00,0xFE,0xFE,0x02,0x02,0x02,0x06,0x0C,0xFC,0xF0,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0C,0x07,0x03,0x00,0x00,0x00,0x00,/*D*/
-		0x00,0xFE,0xFE,0x42,0x42,0x42,0x42,0x42,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,0x00,/*E*/
-		0x00,0xFE,0xFE,0x82,0x82,0x82,0x82,0x82,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*F*/
-		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x82,0x82,0x82,0x84,0x00,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x1F,0x1F,0x00,0x00,0x00,0x00,/*G*/
-		0x00,0xFE,0xFE,0x40,0x40,0x40,0x40,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*H*/
-		0x00,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,/*I*/
-		0x00,0x02,0x02,0x02,0x02,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x08,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,0x00,/*J*/
-		0x00,0xFE,0xFE,0xC0,0xE0,0x30,0x18,0x0C,0x06,0x02,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x01,0x03,0x06,0x0C,0x18,0x10,0x00,0x00,0x00,0x00,/*K*/
-		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,0x00,/*L*/
-		0x00,0x00,0xFE,0x06,0x3C,0xC0,0xC0,0x3C,0x06,0xFE,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x1F,0x00,0x00,0x01,0x01,0x00,0x00,0x1F,0x18,0x00,0x00,0x00,/*M*/
-		0x00,0xFE,0xFE,0x1E,0x70,0x80,0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x03,0x1C,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*N*/
-		0x00,0xF0,0xFC,0x0C,0x02,0x02,0x02,0x0E,0xFC,0xF0,0x00,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x1C,0x10,0x10,0x10,0x0C,0x0F,0x03,0x00,0x00,0x00,0x00,/*O*/
-		0x00,0xFE,0xFE,0x02,0x02,0x02,0x86,0xFC,0x78,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*P*/
-		0x00,0xF0,0xF8,0x0C,0x02,0x02,0x02,0x02,0x0C,0xFC,0xF0,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x1C,0x10,0x30,0x70,0xD8,0x8C,0x8F,0x83,0x40,0x00,0x00,/*Q*/
-		0x00,0xFE,0xFE,0x42,0x42,0xC2,0xE6,0x3C,0x1C,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x01,0x0F,0x1C,0x10,0x00,0x00,0x00,0x00,/*R*/
-		0x00,0x38,0x7C,0x66,0xC2,0xC2,0x82,0x84,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x08,0x10,0x10,0x10,0x10,0x19,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,/*S*/
-		0x00,0x02,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x02,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*T*/
-		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,
-		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,/*U*/
-		0x00,0x0E,0x7E,0xE0,0x00,0x00,0x00,0xE0,0x7C,0x0E,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x03,0x1F,0x18,0x1F,0x03,0x00,0x00,0x00,0x00,0x00,0x00,/*V*/
-		0x00,0x7E,0xFE,0x00,0x00,0xE0,0xE0,0x00,0x00,0xFE,0x7E,0x00,0x00,0x00,
-		0x00,0x00,0x1F,0x18,0x0F,0x01,0x01,0x0F,0x18,0x1F,0x00,0x00,0x00,0x00,/*W*/
-		0x00,0x02,0x06,0x1C,0x38,0xE0,0xE0,0x38,0x1C,0x06,0x02,0x00,0x00,0x00,
-		0x00,0x10,0x18,0x0E,0x07,0x01,0x01,0x07,0x0E,0x18,0x10,0x00,0x00,0x00,/*X*/
-		0x00,0x02,0x0E,0x3C,0xF0,0xC0,0xC0,0xF0,0x3C,0x0E,0x02,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*Y*/
-		0x00,0x02,0x02,0x02,0xC2,0xE2,0x3A,0x0E,0x02,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x1C,0x17,0x11,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,/*Z*/
-		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/* */
+#define FONT_WIDTH 12 /*How many pixels wide the font is*/
+const uint8_t FONT[]={
+		0x00,0xF0,0xFC,0x0E,0x82,0xC2,0x62,0x1E,0xFC,0xF0,0x00,0x00,
+		0x00,0x03,0x0F,0x1F,0x11,0x10,0x10,0x1C,0x0F,0x03,0x00,0x00,/*0*/
+		0x00,0x08,0x04,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,/*1*/
+		0x00,0x04,0x02,0x02,0x02,0xC6,0xFC,0x78,0x00,0x00,0x00,0x00,
+		0x00,0x18,0x1C,0x16,0x13,0x11,0x10,0x10,0x10,0x00,0x00,0x00,/*2*/
+		0x00,0x02,0x02,0x42,0x42,0x66,0xFE,0x9C,0x00,0x00,0x00,0x00,
+		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,/*3*/
+		0x00,0x00,0x80,0xE0,0x30,0x1C,0x06,0xFE,0xFE,0x00,0x00,0x00,
+		0x00,0x03,0x03,0x02,0x02,0x02,0x02,0x1F,0x1F,0x02,0x02,0x00,/*4*/
+		0x00,0x7E,0x7E,0x42,0x42,0x42,0xC2,0x82,0x00,0x00,0x00,0x00,
+		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,/*5*/
+		0x00,0xE0,0xF8,0x8C,0x44,0x42,0x42,0xC2,0x82,0x80,0x00,0x00,
+		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,/*6*/
+		0x00,0x02,0x02,0x02,0x02,0xC2,0xF2,0x1E,0x06,0x00,0x00,0x00,
+		0x00,0x00,0x10,0x1C,0x0F,0x03,0x00,0x00,0x00,0x00,0x00,0x00,/*7*/
+		0x00,0x38,0x7C,0x66,0xC2,0x82,0xC2,0x66,0x7C,0x3C,0x00,0x00,
+		0x00,0x0E,0x0F,0x19,0x10,0x10,0x10,0x19,0x0F,0x0E,0x00,0x00,/*8*/
+		0x00,0x78,0x7C,0xC6,0x82,0x82,0x82,0x46,0xFC,0xF8,0x00,0x00,
+		0x00,0x00,0x10,0x10,0x10,0x10,0x08,0x0C,0x07,0x03,0x00,0x00,/*9*/

+		0x00,0x00,0x80,0xF0,0x1E,0x02,0x1E,0xF0,0x80,0x00,0x00,0x00,
+		0x00,0x1C,0x0F,0x03,0x02,0x02,0x02,0x03,0x0F,0x1C,0x00,0x00,/*A*/
+		0x00,0xFE,0xFE,0x42,0x42,0x42,0xE6,0xBE,0x9C,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,/*B*/
+		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x02,0x02,0x04,0x00,0x00,0x00,
+		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x08,0x00,0x00,0x00,/*C*/
+		0x00,0xFE,0xFE,0x02,0x02,0x02,0x06,0x0C,0xFC,0xF0,0x00,0x00,
+		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0C,0x07,0x03,0x00,0x00,/*D*/
+		0x00,0xFE,0xFE,0x42,0x42,0x42,0x42,0x42,0x00,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,/*E*/
+		0x00,0xFE,0xFE,0x82,0x82,0x82,0x82,0x82,0x00,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*F*/
+		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x82,0x82,0x82,0x84,0x00,0x00,
+		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x1F,0x1F,0x00,0x00,/*G*/
+		0x00,0xFE,0xFE,0x40,0x40,0x40,0x40,0xFE,0xFE,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,/*H*/
+		0x00,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,
+		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,/*I*/
+		0x00,0x02,0x02,0x02,0x02,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,
+		0x00,0x08,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,/*J*/
+		0x00,0xFE,0xFE,0xC0,0xE0,0x30,0x18,0x0C,0x06,0x02,0x00,0x00,
+		0x00,0x1F,0x1F,0x00,0x01,0x03,0x06,0x0C,0x18,0x10,0x00,0x00,/*K*/
+		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,/*L*/
+		0x00,0x00,0xFE,0x06,0x3C,0xC0,0xC0,0x3C,0x06,0xFE,0x00,0x00,
+		0x00,0x10,0x1F,0x00,0x00,0x01,0x01,0x00,0x00,0x1F,0x18,0x00,/*M*/
+		0x00,0xFE,0xFE,0x1E,0x70,0x80,0x00,0xFE,0xFE,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x00,0x00,0x03,0x1C,0x1F,0x1F,0x00,0x00,0x00,/*N*/
+		0x00,0xF0,0xFC,0x0C,0x02,0x02,0x02,0x0E,0xFC,0xF0,0x00,0x00,
+		0x00,0x03,0x0F,0x1C,0x10,0x10,0x10,0x0C,0x0F,0x03,0x00,0x00,/*O*/
+		0x00,0xFE,0xFE,0x02,0x02,0x02,0x86,0xFC,0x78,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,/*P*/
+		0x00,0xF0,0xF8,0x0C,0x02,0x02,0x02,0x02,0x0C,0xFC,0xF0,0x00,
+		0x00,0x03,0x0F,0x1C,0x10,0x30,0x70,0xD8,0x8C,0x8F,0x83,0x40,/*Q*/
+		0x00,0xFE,0xFE,0x42,0x42,0xC2,0xE6,0x3C,0x1C,0x00,0x00,0x00,
+		0x00,0x1F,0x1F,0x00,0x00,0x00,0x01,0x0F,0x1C,0x10,0x00,0x00,/*R*/
+		0x00,0x38,0x7C,0x66,0xC2,0xC2,0x82,0x84,0x00,0x00,0x00,0x00,
+		0x00,0x08,0x10,0x10,0x10,0x10,0x19,0x0F,0x07,0x00,0x00,0x00,/*S*/
+		0x00,0x02,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x02,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*T*/
+		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0xFE,0xFE,0x00,0x00,
+		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,/*U*/
+		0x00,0x0E,0x7E,0xE0,0x00,0x00,0x00,0xE0,0x7C,0x0E,0x00,0x00,
+		0x00,0x00,0x00,0x03,0x1F,0x18,0x1F,0x03,0x00,0x00,0x00,0x00,/*V*/
+		0x00,0x7E,0xFE,0x00,0x00,0xE0,0xE0,0x00,0x00,0xFE,0x7E,0x00,
+		0x00,0x00,0x1F,0x18,0x0F,0x01,0x01,0x0F,0x18,0x1F,0x00,0x00,/*W*/
+		0x00,0x02,0x06,0x1C,0x38,0xE0,0xE0,0x38,0x1C,0x06,0x02,0x00,
+		0x00,0x10,0x18,0x0E,0x07,0x01,0x01,0x07,0x0E,0x18,0x10,0x00,/*X*/
+		0x00,0x02,0x0E,0x3C,0xF0,0xC0,0xC0,0xF0,0x3C,0x0E,0x02,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*Y*/
+		0x00,0x02,0x02,0x02,0xC2,0xE2,0x3A,0x0E,0x02,0x00,0x00,0x00,
+		0x00,0x10,0x1C,0x17,0x11,0x10,0x10,0x10,0x10,0x00,0x00,0x00,/*Z*/
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/* */

+		0x00,0x60,0xF0,0x98,0x0C,0x06,0x02,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x01,0x03,0x06,0x04,0x00,0x00,0x00,0x00,0x00,/*<*/
+		0x00,0x02,0x06,0x0C,0x98,0xF0,0x60,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x04,0x06,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*>*/
+
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x0F,0x0F,0x0F,0x0F,0x00,0x00,0x00,0x00,/*.*/
 };

+const uint8_t Iron_Base[] ={
+		0x00,0x20,0x60,0x60,0x60,0x60,0x60,0x60,0x90,0x90,0x90,0x90,
+		0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,
+		0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x90,0x60,0x60,0x60,
+		0x60,0x60,0x60,0x60,0x60,0x70,0xF8,0x88,0x84,0x82,0x82,0x83,
+		0x83,0x83,0x83,0x83,0x83,0x82,0x82,0x82,0x82,0x83,0x83,0x83,
+		0x83,0x83,0x83,0x82,0x82,0x82,0x82,0x82,0x86,0x84,0x84,0x84,
+		0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,
+		0x84,0x84,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,
+
+};
+//The top pixel row for left arrow / on hint
+const uint8_t Iron_LeftArrow_UP[] = {
+		0x00,0x7C,0x82,0x82,0x82,0x7C,0x00,0xFE,0x08,0x10,0x20,0xFE,//ON
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x88,
+		0x98,0xBF,0xBF,0x98,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+};
+
+const uint8_t Iron_LeftArrow_DOWN[] = {
+		0x00,0x7C,0x82,0x82,0x82,0x7C,0x00,0xFE,0x08,0x10,0x20,0xFE,//ON
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,
+		0x30,0x7E,0x7E,0x30,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+};
+//The top pixel row for both arrows /
+const uint8_t Iron_BothArrows[] = {
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x88,
+		0x98,0xBF,0xBF,0x98,0x88,0x00,0x00,0x00,0x00,0x88,0x98,0xBF,
+		0xBF,0x98,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+};
+//The top pixel row for right arrow / settings hint
+const uint8_t Iron_RightArrow_UP[] = {
+		0x00,0x8C,0x92,0x92,0x92,0x62,0x00,0xFE,0x92,0x92,0x92,0x82,//SE
+		0x00,0x02,0x02,0xFE,0x02,0x02,0x00,0x02,0x02,0xFE,0x02,0x02,//TT
+		0x00,0x00,0x82,0xFE,0x82,0x00,0x00,0xFE,0x08,0x10,0x20,0xFE,//IN
+		0x00,0x7C,0x82,0x82,0xA2,0x62,0x00,0x8C,0x92,0x92,0x92,0x62,//GS
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x88,0x98,0xBF,
+		0xBF,0x98,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+};
+const uint8_t Iron_RightArrow_DOWN[] = {
+		0x00,0x8C,0x92,0x92,0x92,0x62,0x00,0xFE,0x92,0x92,0x92,0x82,//SE
+		0x00,0x02,0x02,0xFE,0x02,0x02,0x00,0x02,0x02,0xFE,0x02,0x02,//TT
+		0x00,0x00,0x82,0xFE,0x82,0x00,0x00,0xFE,0x08,0x10,0x20,0xFE,//IN
+		0x00,0x7C,0x82,0x82,0xA2,0x62,0x00,0x8C,0x92,0x92,0x92,0x62,//GS
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x30,0x7E,
+		0x7E,0x30,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+};
+
+const uint8_t SymbolTable[]={
+
+		0x0E,0x11,0x11,0x0E,0xE0,0xF8,0x0C,0x06,0x03,0x01,0x01,0x01,0x01,0x02,0x1E,0x00,
+		0x00,0x00,0x00,0x00,0x0F,0x3F,0x70,0xC0,0x80,0x80,0x80,0x80,0x80,0x40,0x20,0x00,	// Degrees C
+
+		0x08,0x14,0x22,0x14,0x08,0x02,0x02,0xFE,0x06,0x02,0x02,0x02,0xC2,0x02,0x06,0x1E,
+		0x00,0x00,0x00,0x00,0x00,0x80,0x80,0xFF,0x81,0x81,0x01,0x01,0x03,0x00,0x00,0x00,	// Degrees F
+
+		0xC0,0x30,0x08,0x04,0x04,0x02,0xFA,0xAA,0xFA,0x02,0x04,0x04,0x08,0x30,0xC0,0x00,
+	 	0x07,0x18,0x20,0x40,0x58,0xA4,0xDB,0xDE,0xDB,0xA4,0x58,0x40,0x20,0x18,0x07,0x00, 	// Temp symbol
+
+		0x00,0xF0,0xF0,0x00,0x00,0xF0,0xF0,0xF0,0x00,0x00,0xFC,0xF8,0xF0,0xE0,0xC0,0x80, 	//Right Arrow
+		0x00,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x0F,0x00,0x00,0x3F,0x1F,0x0F,0x07,0x03,0x01,
+
+		0x80,0xC0,0xE0,0xF0,0xF8,0xFC,0x00,0x00,0xF0,0xF0,0xF0,0x00,0x00,0xF0,0xF0,0x00,	//Left Arrow
+		0x01,0x03,0x07,0x0F,0x1F,0x3F,0x00,0x00,0x0F,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00,
+
+		0x11,0x33,0x66,0xCC,0x98,0x30,0x60,0xC0,0xC0,0x60,0x30,0x98,0xCC,0x66,0x33,0x11,
+		0x01,0x03,0x06,0x0C,0x19,0x33,0x66,0xCC,0xCC,0x66,0x33,0x19,0x0C,0x06,0x03,0x01,	//Down Chevron
+
+		0x80,0xC0,0x60,0x30,0x98,0xCC,0x66,0x33,0x33,0x66,0xCC,0x98,0x30,0x60,0xC0,0x80,
+		0x88,0xCC,0x66,0x33,0x19,0x0C,0x06,0x03,0x03,0x06,0x0C,0x19,0x33,0x66,0xCC,0x88,	//Up Chevron
+
+		0x00,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x8C,0x00, 	// Flat Lines
+		0x00,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x31,0x00,
+};
 #endif /* FONT_H_ */
--- a/workspace/ts100/inc/I2C.h
+++ b/workspace/ts100/inc/I2C.h
@@ -1,21 +1,16 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. **********************
-File Name :      I2C.h
-Version :        S100 APP Ver 2.11   
-Description:
-Author :         Celery
-Data:            2015/08/03
-History:
-2015/08/03  : 
-*******************************************************************************/
+/*
+ * I2C.h
+ * I2C wrapper for the stm32 hardware I2C port
+ */
 #ifndef __I2C_H
 #define __I2C_H

-#define I2C_TX    1
-#define I2C_RX    2
+#include "stm32f10x_i2c.h"
+#include "stm32f10x.h"
+#include "stm32f10x_gpio.h"

 void I2C_Configuration(void);
-void Delay_uS(u32 us);
-void I2C_PageWrite(u8* pbuf, u8 numbyte,u8 deviceaddr );
-void I2C_PageRead(u8* pbuf,  u8 numbyte,u8 deviceaddr, u8 readaddr);
+void I2C_PageWrite(u8* pbuf, u8 numbyte, u8 deviceaddr);
+void I2C_PageRead(u8* pbuf, u8 numbyte, u8 deviceaddr, u8 readaddr);
 #endif
 /******************************** END OF FILE *********************************/
--- a/workspace/ts100/inc/Interrupt.h
+++ b/workspace/ts100/inc/Interrupt.h
@@ -1,40 +1,19 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. *******************/
-/* Brief : Interrupt Service Routines                           Author : bure */
-/******************************************************************************/
+/*
+ * Interrupt Service Routines
+ * This file manages all the IRQ events that can be generated
+ */
 #ifndef __INTERRUPT_H
 #define __INTERRUPT_H
 #include <stdint.h>
-//See here for refernce to this block http://embedded.kleier.selfhost.me/vector.php
-/*This loop is used for un assigned IRQ's so that the debugger can catch them*/
-
-void NMI_Handler(void);
-void HardFault_Handler(void);
-void MemManage_Handler(void);
-void BusFault_Handler(void);
-void UsageFault_Handler(void);
-void SVC_Handler(void);
-void DebugMon_Handler(void);
-void PendSV_Handler(void);
-void SysTick_Handler(void);
-
-void WWDG_IRQHandler(void);
-void PVD_IRQHandler(void);
-void TAMPER_STAMP_IRQHandler(void);
-void RTC_WKUP_IRQHandler(void);
-void FLASH_IRQHandler(void);
-
-void USB_LP_CAN1_RX0_IRQHandler(void);
-void I2C1_EV_IRQHandler(void);
-void I2C1_ER_IRQHandler(void);
-void TIM2_IRQHandler(void);
-void TIM3_IRQHandler(void);
-
+/* Functions for access to data */
 extern volatile uint32_t system_Ticks;
 void delayMs(uint32_t ticks);
 volatile extern uint32_t lastKeyPress;
 volatile extern uint32_t lastMovement;

-volatile extern uint16_t keyState;
+volatile extern uint8_t keyState;
+volatile extern uint8_t rawKeys;
+
 inline uint32_t millis() {
 	return system_Ticks;
 }
@@ -57,6 +36,34 @@ inline uint32_t getLastMovement() {
 inline uint16_t getButtons() {
 	return keyState;
 }
+inline uint16_t getRawButtons() {
+	return rawKeys;
+}
+
+
+/*IRQ prototypes*/
+void NMI_Handler(void);
+void HardFault_Handler(void);
+void MemManage_Handler(void);
+void BusFault_Handler(void);
+void UsageFault_Handler(void);
+void SVC_Handler(void);
+void DebugMon_Handler(void);
+void PendSV_Handler(void);
+void SysTick_Handler(void);
+
+void WWDG_IRQHandler(void);
+void PVD_IRQHandler(void);
+void TAMPER_STAMP_IRQHandler(void);
+void RTC_WKUP_IRQHandler(void);
+void FLASH_IRQHandler(void);
+
+void USB_LP_CAN1_RX0_IRQHandler(void);
+void I2C1_EV_IRQHandler(void);
+void I2C1_ER_IRQHandler(void);
+void TIM2_IRQHandler(void);
+void TIM3_IRQHandler(void);
+
 void WWDG_IRQHandler(void);
 void PVD_IRQHandler(void);

--- a/workspace/ts100/inc/MMA8652FC.h
+++ b/workspace/ts100/inc/MMA8652FC.h
@@ -6,7 +6,8 @@
 *
 * http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8652FC.pdf
 *
- * EXTI Motion config setup values lifted from AN4070from NXP
+ * EXTI Motion config setup values lifted from AN4070 from NXP
+ * #defines also taken from ^
 *
 * Ben V. Brown - <ralim@ralimtek.com>
 */
@@ -14,7 +15,7 @@
 #define __MMA8652FC__H


-void StartUp_Acceleromter(void);//This is the only function we expose
+void StartUp_Accelerometer(uint8_t sensitivity);//This is the only function we expose

 //--------------MMA8652 Device ID----------------------------------------------//

--- a/workspace/ts100/inc/Modes.h
+++ b/workspace/ts100/inc/Modes.h
@@ -3,6 +3,9 @@
 *
 *  Created on: 17 Sep 2016
 *      Author: Ralim
+ *
+ *      Modes.h -> Main function for driving the application
+ *      This processes the buttons then does the gui
 */

 #ifndef MODES_H_
@@ -11,27 +14,38 @@
 #include "S100V0_1.h"
 #include "Oled.h"
 #include "PID.h"
+#include "Settings.h"
+#include "Analog.h"
 enum {
-	STARTUP, //we are sitting on the prompt to push a button
-	SOLDERING,
-	TEMP_ADJ,
-	SETTINGS,
-	SLEEP,
+	STARTUP, 		//we are sitting on the prompt to push a button
+	SOLDERING, 		//Normal operating mode
+	TEMP_ADJ,		//Adjust the set temperature
+	SETTINGS,		//Settings menu
+	SLEEP,			//Iron is snoozing due to lack of use
+	COOLING,		//Iron is cooling down -> Warning screen
+	UVLOWARN,		//Unit tripped low voltage
+	THERMOMETER,	//Read the tip temp
+	DCINDISP,		//Disp the input voltage && Cal the DCin voltage divider
+	TEMPCAL,		//Cal tip temp offset
+
 } operatingMode;
+#define SETTINGSOPTIONSCOUNT 11 /*Number of settings in the settings menu*/

 enum {
-	UVLO = 0, SLEEP_TEMP, SLEEP_TIME,
-
+	UVCO = 0,
+	SLEEP_TEMP,
+	SLEEP_TIME,
+	SHUTDOWN_TIME,
+	MOTIONDETECT,
+	MOTIONSENSITIVITY,
+	TEMPDISPLAY,
+	TEMPROUNDING,
+	DISPUPDATERATE,
+	LEFTY,
+	BOOSTMODE,
+	BOOSTTEMP,
 } settingsPage;

-struct {
-	uint32_t SolderingTemp; //current setpoint for the iron
-	uint8_t SleepTime; //minutes to sleep
-	uint32_t SleepTemp; //temp to drop to in sleep
-	uint8_t cutoutVoltage; //X10 the voltage we cutout at for undervoltage
-	uint8_t movementEnabled;
-} systemSettings;
-
 void ProcessUI();
 void DrawUI();
 #endif /* MODES_H_ */
--- a/workspace/ts100/inc/Oled.h
+++ b/workspace/ts100/inc/Oled.h
@@ -1,39 +1,33 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. **********************
- File Name :      Oled.h
- Version :        S100 APP Ver 2.11
- Description:
- Author :         Celery
- Data:            2015/07/07
- History:
- 2015/07/07   ͳһ<CDB3><D2BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
- *******************************************************************************/
+/*
+ * Oled.h
+ * Functions for writing to the OLED screen
+ * Basically wraps drawing text and numbers to the OLED
+ * Uses font.h -> 14 pixel wide fixed width
+ */
 #ifndef _OLED_SSD1306_H
 #define _OLED_SSD1306_H

 #define DEVICEADDR_OLED  0x3c
 #include "stm32f10x.h"
 #include "Interrupt.h"
-void Sc_Pt(u8 Co);
+
 void Oled_DisplayOn(void);
 void Oled_DisplayOff(void);
+
 u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high, u8* ptr);
 void Set_ShowPos(u8 x, u8 y);
-
-u8* Show_posi(u8 posi, u8* ptr, u8 word_width);
-void Clean_Char(int k, u8 wide);
-void Write_Command(u8 Data);
-void Write_Data(u8 Data);
+void Oled_DisplayFlip();
 void GPIO_Init_OLED(void);
-void Init_Oled(void);
+void Init_Oled(uint8_t leftHanded);
 u8* Data_Command(u8 len, u8* ptr);
-void Reg_Command(u8 posi, u8 flag);
-void Clear_Screen(void);
-void Write_InitCommand_data(u32 Com_len, u8* data);
-void Display_BG(void);
+void Clear_Screen(void);//Clear the screen
+/*Functions for writing to the screen*/
 void OLED_DrawString(char* string, uint8_t length);
 void OLED_DrawChar(char c, uint8_t x);
 void OLED_DrawTwoNumber(uint8_t in, uint8_t x);
+void OLED_BlankSlot(uint8_t xStart,uint8_t width);
 void OLED_DrawThreeNumber(uint16_t in, uint8_t x);
-
+void OLED_DrawIDLELogo();
+void OLED_DrawSymbol(uint8_t x,uint8_t symbol);
 #endif
 /******************************** END OF FILE *********************************/
--- a/workspace/ts100/inc/PID.h
+++ b/workspace/ts100/inc/PID.h
@@ -3,12 +3,15 @@
 *
 *  Created on: 20 Sep 2016
 *      Author: ralim
+ *
+ *      Functions for computing the PID for the iron temp
 */

 #ifndef PID_H_
 #define PID_H_
 #include "Analog.h"
 #include "Interrupt.h"
+
 struct {
 	uint32_t kp, ki, kd; //PID values
 } pidSettings;
--- a/workspace/ts100/inc/S100V0_1.h
+++ b/workspace/ts100/inc/S100V0_1.h
@@ -1,14 +1,9 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. ********************
- Brief   : <20>ײ<EFBFBD>Ӳ<EFBFBD><D3B2><EFBFBD><EFBFBD><EFBFBD><EFBFBD>                                          Author : bure
- Modified by Ben V. Brown into English
- *******************************************************************************/
+/*
+ * Defines for the device
+ * These houses the settings for the device hardware
+ */
 #include "stm32f10x.h"
-
-#define PRODUCT_INFO       "TS100"
-#define MCU_TYPE           "STM32F103T8"
-#define SCH_VER            "2.46"
-
-#define SPIx                SPI1
+#include "stm32f10x_gpio.h"
 //--------------------------- key Definitions ------------------------------//
 #define KEY1_PIN          GPIO_Pin_9    //PA8
 #define KEY2_PIN          GPIO_Pin_6    //PA6
@@ -17,45 +12,24 @@
 #define KEY_B			  KEY2_PIN
 #define BUT_A			  0x01
 #define BUT_B			  0x02
-#define BUT_AB			  BUT_A|BUT_B
-#define KEY_1             !(GPIOA->IDR & KEY1_PIN)
-#define KEY_2             !(GPIOA->IDR & KEY2_PIN)
-#define KEY_DFU           KEY_1

-#define I2C1_DMA_CHANNEL_TX           DMA1_Channel6
-#define I2C1_DMA_CHANNEL_RX           DMA1_Channel7
-
-#define I2C2_DMA_CHANNEL_TX           DMA1_Channel4
-#define I2C2_DMA_CHANNEL_RX           DMA1_Channel5
-
-#define I2C1_DR_Address               0x40005410
-#define I2C2_DR_Address               0x40005810

 //--------------------------- OLED  ------------------------------//
 #define OLED_RST_PIN        GPIO_Pin_8      //PA9
 #define OLED_RST()          GPIO_ResetBits(GPIOA, OLED_RST_PIN)
 #define OLED_ACT()          GPIO_SetBits  (GPIOA, OLED_RST_PIN)

-//------------------------------  --------------------------------//
+//------------------------------ Iron Heater --------------------------------//
 #define HEAT_PIN            GPIO_Pin_4
-
 #define HEAT_OFF()          GPIOB->BRR = HEAT_PIN
 #define HEAT_ON()           GPIOB->BSRR = HEAT_PIN

-//-----------------------VB---------------------------------------//
+//-----------------------Battery voltage measurement---------------------------------------//
 #define   VB_PIN            GPIO_Pin_1      //PB1(Ai9)
-//----------------------------ADX345 INT1,INT2--------------------------------//
+
+//----------------------------Accelerometer INT1,INT2--------------------------------//
 #define   INT1_PIN            GPIO_Pin_5    //PB5  
 #define   INT2_PIN            GPIO_Pin_3    //PB3
-//------------------------------ GPIO  -------------------------------//
-
-#define GPIOA_OUTPUT()      GPIOA->ODR  = 0xFFFF;
-#define GPIOA_L_DEF()       GPIOA->CRL  = 0x08888888; /* Ai7 K2 xxx xxx xxx xxx xxx xxx */
-#define GPIOA_H_DEF()       GPIOA->CRH  = 0x8BBBB883; /* xxx SWC SWD D+  D-  xxx K1 nCR  */
-
-#define GPIOB_OUTPUT()      GPIOB->ODR  = 0xFFFF;
-#define GPIOB_L_DEF()       GPIOB->CRL  = 0x44838800; /* SDA SCL It1 Po It2 xxx Ai9 Ai8 */
-#define GPIOB_H_DEF()       GPIOB->CRH  = 0x88888888; /* xxx xxx xxx xxx xxx xxx xxx xxx */

 //--------------------------------- RCC Clock Config ---------------------------------//

@@ -72,4 +46,3 @@
                                           ||+-------Bit22 = 1 USB prescaler is PLL clock
                                           ++--------Bits31~27 Reserved*/

-/******************************** END OF FILE *********************************/
--- a/workspace/ts100/inc/Settings.h
+++ b/workspace/ts100/inc/Settings.h
@@ -0,0 +1,53 @@
+/*
+ * Settings.h
+ *
+ *  Created on: 29 Sep 2016
+ *      Author: Ralim
+ *
+ *      Houses the system settings and allows saving / restoring from flash
+ */
+
+#ifndef SETTINGS_H_
+#define SETTINGS_H_
+#include <stdint.h>
+#include "stm32f10x_flash.h"
+#define SETTINGSVERSION 10 /*Change this if you change the struct below to prevent people getting out of sync*/
+//Motion Sensitivity
+#define MOTION_HIGH 		(0x00)
+#define MOTION_MED  		(0x01)
+#define MOTION_LOW  		(0x02)
+//Display Speeds
+#define DISPLAYMODE_FAST 	(0x00)
+#define DISPLAYMODE_MEDIUM 	(0x01)
+#define DISPLAYMODE_SLOW	(0x02)
+//Rounding Modes
+#define ROUNDING_NONE			(0x00)
+#define ROUNDING_FIVE			(0x01)
+#define ROUNDING_TEN			(0x02)
+
+/*
+ * This struct must be a multiple of 2 bytes as it is saved / restored from flash in uint16_t chunks
+ */
+struct {
+	uint16_t SolderingTemp; 		//current set point for the iron
+	uint32_t SleepTemp; 			//temp to drop to in sleep
+	uint8_t version;				//Used to track if a reset is needed on firmware upgrade
+	uint8_t SleepTime; 				//minutes timeout to sleep
+	uint8_t cutoutVoltage:5; 		//The voltage we cut out at for under voltage
+	uint8_t movementEnabled:1;		//If movement is enabled
+	uint8_t displayTempInF:1;		//If we need to convert the C reading to F
+	uint8_t flipDisplay:1;			//If true we want to invert the display for lefties
+	uint8_t sensitivity:5;			//Sensitivity of accelerometer
+	uint8_t ShutdownTime:6;			//Time until unit shuts down if left alone
+	uint8_t displayUpdateSpeed:2;	//How fast the display updates / temp showing mode
+	uint8_t temperatureRounding:2;	//Rounding mode for the temperature
+	uint8_t boostModeEnabled:1;		//Boost mode swaps BUT_A in soldering mode to temporary soldering temp over-ride
+	uint16_t tempCalibration;		//Temperature calibration value
+	uint16_t voltageDiv;			//Voltage divisor factor
+	uint16_t BoostTemp; 			//Boost mode set point for the iron
+} systemSettings;
+
+void saveSettings();
+void restoreSettings();
+void resetSettings();
+#endif /* SETTINGS_H_ */
--- a/workspace/ts100/inc/stm32f10x_conf.h
+++ b/workspace/ts100/inc/stm32f10x_conf.h
@@ -1,85 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32f10x_conf.h
-  * @author  MCD Application Team
-  * @version V4.0.0
-  * @date    21-January-2013
-  * @brief   Library configuration file.
-  ******************************************************************************
-  * @attention
-  *
-  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
-  *
-  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
-  * You may not use this file except in compliance with the License.
-  * You may obtain a copy of the License at:
-  *
-  *        http://www.st.com/software_license_agreement_liberty_v2
-  *
-  * Unless required by applicable law or agreed to in writing, software 
-  * distributed under the License is distributed on an "AS IS" BASIS, 
-  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-  * See the License for the specific language governing permissions and
-  * limitations under the License.
-  *
-  ******************************************************************************
-  */
-
-
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __STM32F10x_CONF_H
-#define __STM32F10x_CONF_H
-
-/* Includes ------------------------------------------------------------------*/
-/* Uncomment the line below to enable peripheral header file inclusion */
-#include "stm32f10x_adc.h"
-#include "stm32f10x_bkp.h"
-#include "stm32f10x_can.h"
-#include "stm32f10x_crc.h"
-#include "stm32f10x_dac.h"
-#include "stm32f10x_dbgmcu.h"
-#include "stm32f10x_dma.h"
-#include "stm32f10x_exti.h"
-#include "stm32f10x_flash.h"
-#include "stm32f10x_fsmc.h"
-#include "stm32f10x_gpio.h"
-#include "stm32f10x_i2c.h" 
-#include "stm32f10x_iwdg.h"
-#include "stm32f10x_pwr.h"
-#include "stm32f10x_rcc.h"
-#include "stm32f10x_rtc.h"
-#include "stm32f10x_sdio.h"
-#include "stm32f10x_spi.h"
-#include "stm32f10x_tim.h"
-#include "stm32f10x_usart.h"
-#include "stm32f10x_wwdg.h"
-#include "misc.h"   /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */
-
-/* Exported types ------------------------------------------------------------*/
-/* Exported constants --------------------------------------------------------*/
-/* Uncomment the line below to expanse the "assert_param" macro in the 
-   Standard Peripheral Library drivers code */
-/* #define USE_FULL_ASSERT    1 */
-
-/* Exported macro ------------------------------------------------------------*/
-#ifdef  USE_FULL_ASSERT
-
-/*******************************************************************************
-* Macro Name     : assert_param
-* Description    : The assert_param macro is used for function's parameters check.
-* Input          : - expr: If expr is false, it calls assert_failed function
-*                    which reports the name of the source file and the source
-*                    line number of the call that failed. 
-*                    If expr is true, it returns no value.
-* Return         : None
-*******************************************************************************/ 
-  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
-/* Exported functions ------------------------------------------------------- */
-  void assert_failed(uint8_t* file, uint32_t line);
-#else
-  #define assert_param(expr) ((void)0)
-#endif /* USE_FULL_ASSERT */
-
-#endif /* __STM32F10x_CONF_H */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
--- a/workspace/ts100/src/Analog.c
+++ b/workspace/ts100/src/Analog.c
@@ -8,12 +8,14 @@
 */
 #include "Analog.h"

-uint16_t readDCVoltage() {
+//Reads the dc input and returns it as X10 voltage (ie 236 = 23.6V)
+//Seems unstable below 9.5V input
+uint16_t readDCVoltage(uint16_t divFactor) {
 	uint16_t reading = 0;
 	for (u8 i = 0; i < 10; i++) {
 		reading += ADC_GetConversionValue(ADC2);
 	}
-	reading /= 144; //take the average and convert to X10 voltage
+	reading /= divFactor; //take the average and convert to X10 voltage
 	return reading; //return the read voltage
 }

@@ -21,7 +23,7 @@ uint16_t readDCVoltage() {
 //This allows us to read it in X10 mode
 //Returns temperature in C X10 mode
 int16_t readTipTemp() {
-	static uint32_t rollingAverage[4];
+	static uint32_t rollingAverage[16];
 	static uint8_t rIndex = 0;

 	/*The head has a thermocouple inline with the heater
@@ -52,9 +54,13 @@ int16_t readTipTemp() {
 	ad_sum = ad_sum - max - min; //remove the two outliers
 	avg_data = ad_sum / 8; //take the average
 	rollingAverage[rIndex] = avg_data;
-	rIndex = (rIndex + 1) % 4;
+	rIndex = (rIndex + 1) % 16;
 	return (rollingAverage[0] + rollingAverage[1] + rollingAverage[2]
-			+ rollingAverage[3]) / 4; //get the average
+			+ rollingAverage[3] + rollingAverage[4] + rollingAverage[5]
+			+ rollingAverage[6] + rollingAverage[7] + rollingAverage[8]
+			+ rollingAverage[9] + rollingAverage[10] + rollingAverage[11]
+			+ rollingAverage[12] + rollingAverage[13] + rollingAverage[14]
+			+ rollingAverage[15]) / 16; //get the average

 }

@@ -102,16 +108,31 @@ uint16_t Get_ADC1Value(uint8_t i) {
 	return ADC1ConvertedValue[i];
 }
 //This returns the calibrated temperature reading of the iron temp
-uint16_t readIronTemp(uint16_t calibration_temp, uint8_t read) {
+//inputs : calibration value / wether to take a new reading or not
+uint16_t readIronTemp(uint16_t calibration_temp, uint8_t read,
+		uint16_t setPointTemp) {
 	static uint16_t calTemp = 0;
 	static uint16_t lastVal = 0;
-
+	static uint16_t lastSetTemp;
+	if (setPointTemp != 0xFFFF)
+		lastSetTemp = setPointTemp;
 	if (calibration_temp != 0)
 		calTemp = calibration_temp;

 	if (read) {
-		lastVal = (readTipTemp() * 1000 + 806 * readSensorTemp()
-				- calTemp * 1000) / 806;
+		int16_t compensation = 80 + 150 * (lastSetTemp - 1000) / 3000;
+		int16_t tipTemp = readTipTemp();
+		int16_t ColdJTemp = readSensorTemp();
+		if (lastSetTemp == 1000)
+			compensation -= 10;
+
+		if (lastSetTemp != 0) {
+			if (tipTemp > (compensation + calTemp))
+				tipTemp -= compensation;
+		}
+		if (ColdJTemp > 400)
+			ColdJTemp = 400;
+		lastVal = (tipTemp * 1000 + 807 * ColdJTemp - calTemp * 1000) / 807;

 	}

--- a/workspace/ts100/src/Bios.c
+++ b/workspace/ts100/src/Bios.c
@@ -1,11 +1,11 @@
 /*
 * Setup all the basic hardware in the system and handle timer3 tick
 */
-#include "APP_Version.h"
+
 #include "Bios.h"
 #include "I2C.h"

-/******************************************************************************/
+
 #define ADC1_DR_Address    ((u32)0x4001244C)
 volatile uint32_t gHeat_cnt = 0;

@@ -58,20 +58,6 @@ void GPIO_Config(void) {
 	GPIO_PinRemapConfig(GPIO_Remap_SWJ_NoJTRST, ENABLE);
 	GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);

-	GPIOA_OUTPUT()
-	;
-	GPIOA_L_DEF()
-	;
-	GPIOA_H_DEF()
-	;
-
-	GPIOB_OUTPUT()
-	;
-	GPIOB_L_DEF()
-	;
-	GPIOB_H_DEF()
-	;
-
 	//------ PA7 TMP36 Analog input ----------------------------------------//
 	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
--- a/workspace/ts100/src/I2C.c
+++ b/workspace/ts100/src/I2C.c
@@ -1,229 +1,148 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. **********************
-File Name :      I2C.c
-Version :        S100 APP Ver 2.11   
-Description:
-Author :         Celery
-Data:            2015/07/20
-History:
-2015/07/07   ͳһ<CDB3><D2BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
-2015/07/21   I2C_DELAYTIME = 2;
-*******************************************************************************/
-
-#include "stm32f10x.h"
+/*
+ * I2C.h hardware interface class
+ * Based on the STM32 app note AN2824
+ */
 #include "I2C.h"
-#include "Bios.h"
-#include "Oled.h"
-#include "S100V0_1.h"

-// --------- <20><><EFBFBD><EFBFBD>I2C<32>ӿ<EFBFBD><D3BF><EFBFBD>ض<EFBFBD><D8B6><EFBFBD>-------- //
-#define SDA          GPIO_Pin_7
-#define	SCL		       GPIO_Pin_6
+/*
+ * Configure the I2C port hardware
+ */
+void I2C_Configuration(void) {
+	GPIO_InitTypeDef GPIO_InitStructure;
+	I2C_InitTypeDef I2C_InitStructure;

-#define HIGH         1
-#define LOW          0
+	/* PB6,7 SCL and SDA */
+	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
+	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
+	GPIO_Init(GPIOB, &GPIO_InitStructure);

-#define SDA_VAL      GPIO_ReadInputDataBit(GPIOB, SDA)
-#define SCL_VAL      GPIO_ReadInputDataBit(GPIOB, SCL)
-
-#define I2C_MORE     1
-#define I2C_LAST     0
-#define I2C_TIMEOUT  255
-
-#define FAILURE      0
-#define SUCCEED      1
-#define I2C_DELAYTIME 2
-
-static void Sim_I2C_Set(u8 pin, u8 status);
-static void Sim_I2C_Stop(void);
-static void Sim_I2C_Start(void);
-static u8   Sim_I2C_RD_Byte(u8 more);
-static u8   Sim_I2C_WR_Byte(u8 data);
-
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: Delay_uS
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: <20><><EFBFBD><EFBFBD><EFBFBD>ʱ
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:us 
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void Delay_uS(u32 us)
-{
-    while(us) us--;
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: I2C_Configuration
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: <20><><EFBFBD><EFBFBD>I2C
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:NULL
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void I2C_Configuration(void)
-{
-    GPIO_InitTypeDef GPIO_InitStructure;
-    I2C_InitTypeDef  I2C_InitStructure;
-
-    GPIO_Init_OLED();
-    /* PB6,7 SCL and SDA */
-    GPIO_InitStructure.GPIO_Pin   =  GPIO_Pin_6 | GPIO_Pin_7;
-    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
-    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AF_OD;
-    GPIO_Init(GPIOB, &GPIO_InitStructure);
-
-    /* I2C1 configuration ------------------------------------------------------*/
-    I2C_InitStructure.I2C_Mode                = I2C_Mode_I2C;
-    I2C_InitStructure.I2C_DutyCycle           = I2C_DutyCycle_2;
-    I2C_InitStructure.I2C_OwnAddress1         = DEVICEADDR_OLED;
-    I2C_InitStructure.I2C_Ack                 = I2C_Ack_Enable;
-    I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
-    I2C_InitStructure.I2C_ClockSpeed          = 100000;//100k
-    I2C_Init(I2C1, &I2C_InitStructure);
-    I2C_Cmd(I2C1, ENABLE);
+	/* I2C1 configuration ------------------------------------------------------*/
+	I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
+	I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2;
+	I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
+	I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
+	I2C_InitStructure.I2C_ClockSpeed = 400000; //400k
+	I2C_Init(I2C1, &I2C_InitStructure);
+	I2C_Cmd(I2C1, ENABLE);
 }

-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: I2C_Configuration
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: <20><><EFBFBD><EFBFBD>I2C
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:NULL
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void Sim_I2C_Set(u8 pin, u8 status)
-{
-    if(status == HIGH) GPIO_SetBits  (GPIOB, pin);
-    if(status == LOW)  GPIO_ResetBits(GPIOB, pin);
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: Sim_I2C_Start
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: <20><>ʼ
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:NULL
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void Sim_I2C_Start(void)
-{
-    GPIO_InitTypeDef  GPIO_InitStructure;
+/*
+ * Writes a page of data over I2C using the I2C1 peripheral in the stm32
+ *
+ */
+void I2C_PageWrite(u8* buf, u8 nbyte, u8 deviceaddr) {

-    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE); // I2C_PIN_EN();
-    GPIO_InitStructure.GPIO_Pin   = SCL | SDA;
-    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_OD;
-    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
-    GPIO_Init       (GPIOB, &GPIO_InitStructure);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY)) {
+	}
+	// Intiate Start Sequence
+	I2C_GenerateSTART(I2C1, ENABLE);
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) {
+	}
+	// Send Address
+	I2C_Send7bitAddress(I2C1, deviceaddr << 1, I2C_Direction_Transmitter);
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)) {
+	}
+	// Write first byte EV8_1
+	I2C_SendData(I2C1, *buf++);

-    Sim_I2C_Set(SCL, LOW);  // SCL low
-    Sim_I2C_Set(SDA, HIGH); // SDA float, set as output high
-    Sim_I2C_Set(SCL, HIGH); // SCL high
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SDA, LOW);  // SDA high->low while sclk high, S state occur...
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SCL, LOW);  // SCL low
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: Sim_I2C_Stop
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: ֹͣ
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:NULL
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void Sim_I2C_Stop(void)
-{
-    Sim_I2C_Set(SCL, LOW);  // SCL low
-    Sim_I2C_Set(SDA, LOW);  // SDA low
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SCL, HIGH); // SCL high
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SDA, HIGH); // SDA low->high while sclk high, P state occur
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SCL, LOW);  //  SCL low
-    Delay_uS(I2C_DELAYTIME);
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: Sim_I2C_WR_Byte
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:<3A><>I2Cд<43><D0B4>λ<EFBFBD><CEBB><EFBFBD><EFBFBD>
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:dataҪд<D2AA><D0B4><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-u8 Sim_I2C_WR_Byte(u8 data)
-{
-    u8 i = 8;
+	while (--nbyte) {
+		// wait on BTF
+		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+		}
+		I2C_SendData(I2C1, *buf++);
+	}

-    while(i--) { 								//send out a bit by sda line.
-        Sim_I2C_Set(SCL, LOW);                  // sclk low
-        if(data & 0x80) Sim_I2C_Set(SDA, HIGH); // send bit is 1
-        else            Sim_I2C_Set(SDA, LOW);  // send bit is 0
-        Delay_uS(I2C_DELAYTIME);
-        Sim_I2C_Set(SCL, HIGH);                 // SCL high
-        Delay_uS(I2C_DELAYTIME);
-        data <<=1;								// left shift 1 bit, MSB send first.
-    }
-    Sim_I2C_Set(SCL, LOW);                    // SCL low
-    Sim_I2C_Set(SDA, HIGH);                   // SDA set as input
-    for(i=I2C_TIMEOUT; i!=0; i--) {			// wait for sda low	to receive ack
-        Delay_uS(I2C_DELAYTIME);
-        if (!SDA_VAL) {
-            Sim_I2C_Set(SCL, HIGH);               // SCL high
-            Delay_uS(I2C_DELAYTIME);
-            Sim_I2C_Set(SCL, LOW);                // SCL_LOW();
-            Delay_uS(I2C_DELAYTIME);
-            return SUCCEED;
-        }
-    }
-    return FAILURE;
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: Sim_I2C_RD_Byte
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:<3A><>I2C<32><43><EFBFBD><EFBFBD>λ<EFBFBD><CEBB><EFBFBD><EFBFBD>
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:more
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:<3A><><EFBFBD><EFBFBD><EFBFBD>İ<EFBFBD>λ<EFBFBD><CEBB><EFBFBD><EFBFBD>
-*******************************************************************************/
-u8 Sim_I2C_RD_Byte(u8 more)
-{
-    u8 i = 8, byte = 0;
+	while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+	}
+	I2C_GenerateSTOP(I2C1, ENABLE);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_STOPF)) {
+	}

-    Sim_I2C_Set(SDA, HIGH);             // SDA set as input
-    while(i--) {
-        Sim_I2C_Set(SCL, LOW);            // SCL low
-        Delay_uS(I2C_DELAYTIME);
-        Sim_I2C_Set(SCL, HIGH);           // SCL high
-        Delay_uS(I2C_DELAYTIME);
-        byte <<=1;				          //recv a bit
-        if (SDA_VAL) byte |= 0x01;
-    }
-    Sim_I2C_Set(SCL, LOW);
-    if(!more)	Sim_I2C_Set(SDA, HIGH);   //last byte, send nack.
-    else		Sim_I2C_Set(SDA, LOW);    //send ack
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SCL, HIGH);             // SCL_HIGH();
-    Delay_uS(I2C_DELAYTIME);
-    Sim_I2C_Set(SCL, LOW);
-    return byte;
 }
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: I2C_PageWrite
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:<3A><> <20><>ַ deviceaddr д<><D0B4>numbyte<74><65><EFBFBD>ֽڵ<D6BD><DAB5><EFBFBD><EFBFBD>ݣ<EFBFBD>д<EFBFBD><D0B4><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>pbuf
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:pbuf д<><D0B4><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ݣ<EFBFBD>numbyte Ϊд<CEAA><D0B4><EFBFBD><EFBFBD>ֽ<EFBFBD><D6BD><EFBFBD><EFBFBD><EFBFBD>deviceaddrΪд<CEAA><D0B4>ĵ<EFBFBD>ַ
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:NULL
-*******************************************************************************/
-void I2C_PageWrite(u8* pbuf, u8 numbyte,u8 deviceaddr )
-{
-    Sim_I2C_Start();
-    Sim_I2C_WR_Byte(deviceaddr<<1);
-    while(numbyte--) Sim_I2C_WR_Byte(*pbuf++);
-    Sim_I2C_Stop();
-}
-/*******************************************************************************
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: I2C_PageRead
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>:<3A><>I2C<32><43><EFBFBD><EFBFBD>λ<EFBFBD><CEBB><EFBFBD><EFBFBD>
-<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>: pbuf <20><><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Ĵ<EFBFBD>ŵ<EFBFBD>ַ numbyteΪ<65><CEAA><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>ֽ<EFBFBD><D6BD><EFBFBD> 
-          deviceaddr<64>豸<EFBFBD><E8B1B8>ַ readaddr<64><72>ȡ<EFBFBD><C8A1><EFBFBD><EFBFBD><EFBFBD>ݵ<EFBFBD>ַ
-<EFBFBD><EFBFBD><EFBFBD>ز<EFBFBD><EFBFBD><EFBFBD>:<3A><><EFBFBD><EFBFBD><EFBFBD>İ<EFBFBD>λ<EFBFBD><CEBB><EFBFBD><EFBFBD>
-*******************************************************************************/
-void I2C_PageRead(u8* pbuf,  u8 numbyte,u8 deviceaddr, u8 readaddr)
-{
-    Sim_I2C_Start();
-    Sim_I2C_WR_Byte(deviceaddr<<1);
-    Sim_I2C_WR_Byte(readaddr);
-    Sim_I2C_Start();
-    Sim_I2C_WR_Byte((deviceaddr<<1)|1);

-    while(numbyte--) {
-        if(numbyte) *pbuf++ = Sim_I2C_RD_Byte(I2C_MORE);
-        else	  	  *pbuf++ = Sim_I2C_RD_Byte(I2C_LAST);
-    }
-    Sim_I2C_Stop();
+/*
+ * Read Page of data using I2C1 peripheral
+ */
+
+void I2C_PageRead(u8* buf, u8 nbyte, u8 deviceaddr, u8 readaddr) {
+	I2C_GenerateSTART(I2C1, ENABLE);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_SB) == RESET)
+		;
+	I2C_Send7bitAddress(I2C1, deviceaddr << 1, I2C_Direction_Transmitter);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_ADDR) == RESET)
+		;
+	I2C_GetFlagStatus(I2C1, I2C_FLAG_MSL);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_TXE) == RESET)
+		;
+	// Send an 8bit byte address
+	I2C_SendData(I2C1, readaddr);
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY)) {
+	}
+	I2C_AcknowledgeConfig(I2C1, DISABLE);
+	I2C_NACKPositionConfig(I2C1, I2C_NACKPosition_Current);
+	I2C_GenerateSTART(I2C1, ENABLE);
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) {
+	}
+	I2C_Send7bitAddress(I2C1, deviceaddr << 1, I2C_Direction_Receiver);
+	while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_ADDR)) {
+	}
+	if (nbyte == 1) {
+		// Clear Ack bit
+		I2C_AcknowledgeConfig(I2C1, DISABLE);
+		// EV6_1 -- must be atomic -- Clear ADDR, generate STOP
+		__disable_irq();
+		(void) I2C1->SR2;
+		I2C_GenerateSTOP(I2C1, ENABLE);
+		__enable_irq();
+		// Receive data   EV7
+		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_RXNE)) {
+		}
+		*buf++ = I2C_ReceiveData(I2C1);
+	} else if (nbyte == 2) {
+		// Set POS flag
+		I2C_NACKPositionConfig(I2C1, I2C_NACKPosition_Next);
+		// EV6_1 -- must be atomic and in this order
+		__disable_irq();
+		(void) I2C1->SR2;                           // Clear ADDR flag
+		I2C_AcknowledgeConfig(I2C1, DISABLE);       // Clear Ack bit
+		__enable_irq();
+		// EV7_3  -- Wait for BTF, program stop, read data twice
+		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+		}
+		__disable_irq();
+		I2C_GenerateSTOP(I2C1, ENABLE);
+		*buf++ = I2C1->DR;
+		__enable_irq();
+		*buf++ = I2C1->DR;
+	} else {
+		(void) I2C1->SR2;                           // Clear ADDR flag
+		while (nbyte-- != 3) {
+			// EV7 -- cannot guarantee 1 transfer completion time, wait for BTF
+			//        instead of RXNE
+			while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+			}
+			*buf++ = I2C_ReceiveData(I2C1);
+		}
+
+		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+		}
+		// EV7_2 -- Figure 1 has an error, doesn't read N-2 !
+		I2C_AcknowledgeConfig(I2C1, DISABLE);           // clear ack bit
+		__disable_irq();
+		*buf++ = I2C_ReceiveData(I2C1);             // receive byte N-2
+		I2C_GenerateSTOP(I2C1, ENABLE);                  // program stop
+		__enable_irq();
+		*buf++ = I2C_ReceiveData(I2C1);             // receive byte N-1
+		// wait for byte N
+		while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_RECEIVED)) {
+		}
+		*buf++ = I2C_ReceiveData(I2C1);
+		nbyte = 0;
+	}
+	// Wait for stop
+	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_STOPF)) {
+	}
+	return;
 }
-/******************************** END OF FILE *********************************/
+
--- a/workspace/ts100/src/Interrupt.c
+++ b/workspace/ts100/src/Interrupt.c
@@ -4,7 +4,8 @@

 volatile uint32_t system_Ticks;
 volatile uint32_t lastKeyPress; //millis() at the last button event
-volatile uint16_t keyState; //tracks the button status
+volatile uint8_t keyState; //tracks the button status
+volatile uint8_t rawKeys;
 volatile uint32_t lastMovement; //millis() at last movement event

 //Delay in milliseconds using systemTick
@@ -53,20 +54,26 @@ void TIM3_IRQHandler(void) {
 //used for buttons and movement
 void EXTI9_5_IRQHandler(void) {
 //we are interested in line 9 and line 6 for buttons
-	//Lien 5 == movement
+	//Line 5 == movement
 	if (EXTI_GetITStatus(EXTI_Line9) != RESET) {
-		if (GPIO_ReadInputDataBit(GPIOA, KEY_A) == SET)
+		if (GPIO_ReadInputDataBit(GPIOA, KEY_A) == SET) {
 			keyState &= ~(BUT_A);
-		else
+			rawKeys &= ~BUT_A;
+		} else {
 			keyState |= BUT_A;
-		lastKeyPress = millis();
+			rawKeys |= BUT_A;
+			lastKeyPress = millis();
+		}
 		EXTI_ClearITPendingBit(EXTI_Line9);
 	} else if (EXTI_GetITStatus(EXTI_Line6) != RESET) {
-		if (GPIO_ReadInputDataBit(GPIOA, KEY_B) == SET)
+		if (GPIO_ReadInputDataBit(GPIOA, KEY_B) == SET) {
 			keyState &= ~(BUT_B);
-		else
+			rawKeys &= ~BUT_B;
+		} else {
 			keyState |= BUT_B;
-		lastKeyPress = millis();
+			rawKeys |= BUT_B;
+			lastKeyPress = millis();
+		}
 		EXTI_ClearITPendingBit(EXTI_Line6);
 	} else if (EXTI_GetITStatus(EXTI_Line5) != RESET) {	//Movement Event
 		lastMovement = millis();
@@ -205,5 +212,3 @@ void USB_LP_CAN1_RX0_IRQHandler(void) {

 }

-/*********************************  END OF FILE  ******************************/
-
--- a/workspace/ts100/src/MMA8652FC.c
+++ b/workspace/ts100/src/MMA8652FC.c
@@ -20,28 +20,37 @@ void I2C_RegisterWrite(uint8_t reg, uint8_t data) {
 	tx_data[0] = reg;
 	tx_data[1] = data;
 	I2C_PageWrite(tx_data, 2, DEVICE_ADDR);
-
 }

 uint8_t I2C_RegisterRead(uint8_t reg) {
 	u8 tx_data[3];
 	tx_data[0] = reg;
-
 	I2C_PageRead(tx_data, 1, DEVICE_ADDR, reg);
 	return tx_data[0];
-
 }

-void StartUp_Acceleromter(void) {
-
+void StartUp_Accelerometer(uint8_t sensitivity) {
 	I2C_RegisterWrite(CTRL_REG2, 0); //Normal mode
-	I2C_RegisterWrite( CTRL_REG2, 0x40);		// Reset all registers to POR values
+	I2C_RegisterWrite( CTRL_REG2, 0x40);	// Reset all registers to POR values
 	delayMs(2);		// ~1ms delay
-	I2C_RegisterWrite(FF_MT_CFG_REG, 0x78);// Enable motion detection for X and Y axis, latch enabled
-	I2C_RegisterWrite(FF_MT_THS_REG, 0x0F);		// Set threshold
+	I2C_RegisterWrite(FF_MT_CFG_REG, 0x78);	// Enable motion detection for X and Y axis, latch enabled
+	uint8_t sens =0x0F;
+	switch(sensitivity)
+	{
+	case 0:
+		sens=0x1A;
+		break;
+	case 1:
+		sens=0x20;
+		break;
+	case 2:
+		sens=0x2A;
+		break;
+	}
+	I2C_RegisterWrite(FF_MT_THS_REG, sens);		// Set threshold
 	I2C_RegisterWrite(FF_MT_COUNT_REG, 0x01);	// Set debounce to 100ms

 	I2C_RegisterWrite( CTRL_REG4, 0x04);		// Enable motion interrupt
-	I2C_RegisterWrite( CTRL_REG5, 0x04);		// Route motion interrupts to INT1 ->PB5 ->EXTI
+	I2C_RegisterWrite( CTRL_REG5, 0x04);// Route motion interrupts to INT1 ->PB5 ->EXTI5
 	I2C_RegisterWrite( CTRL_REG1, 0x19);		// ODR=100 Hz, Active mode
 }
--- a/workspace/ts100/src/Main.c
+++ b/workspace/ts100/src/Main.c
@@ -1,53 +1,43 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. **********************
- File Name :      main.c
- Version :        S100 APP Ver 2.11
- Description:
- Author :         Celery
- Data:            2015/07/07
- History:
- 2016/8/11	Updates by Ben V. Brown <ralim@ralimtek.com> - Cleanup and english comments
- 2015/07/07   ͳһ<CDB3><D2BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
- *******************************************************************************/
-#include <string.h>
-#include <stdio.h>
-#include "APP_Version.h"
+/*
+ * Created by Ben V. Brown
+ */
+
 #include "Modes.h"
 #include "Bios.h"
-#include "I2C.h"
 #include "MMA8652FC.h"
 #include "PID.h"
 #include "Oled.h"
-#include "Interrupt.h"
+#include "Settings.h"
+#include "I2C.h"
+void setup();

 int main(void) {
-	RCC_Config(); //setup system clock
-	//NVIC_Config(0x4000);//this shifts the NVIC table to be offset
-	NVIC_Config(0x0000);
-	GPIO_Config(); //setup all the GPIO pins
-	Init_EXTI();
-	//Init_Timer2(); //init the timers
-
-	Init_Timer3();
-	I2C_Configuration(); //init the i2c bus
-
-	Adc_Init(); //init adc and dma
-	StartUp_Acceleromter(); //start the accelerometer
-
-	Init_Oled(); //init the OLED display
-	Clear_Screen(); //clear the display buffer to black
-	systemSettings.SleepTemp = 900;
-	systemSettings.SleepTime = 1;
-	systemSettings.SolderingTemp = 1000;
-	systemSettings.movementEnabled = 1; //we use movement detection
-	readIronTemp(239, 0); //load the default calibration value
-	setupPID(); //init the PID values
-
-	Start_Watchdog(3000); //start the system watchdog as 3 seconds
+	setup();/*Setup the system*/
 	while (1) {
-		Clear_Watchdog(); //reset the Watchdog
+		Clear_Watchdog(); //reset the Watch dog timer
 		ProcessUI();
 		DrawUI();
-		delayMs(50);
+		delayMs(50); //Slow the system down a little bit
 	}
 }
-/******************************** END OF FILE *********************************/
+void setup() {
+	RCC_Config(); 										//setup system clock
+	NVIC_Config(0x4000); 								//this shifts the NVIC table to be offset, for the usb bootloader's size
+	GPIO_Config(); 										//setup all the GPIO pins
+	Init_EXTI(); 										//Init the EXTI inputs
+	Init_Timer3(); 										//Used for the soldering iron tip
+	Adc_Init(); 										//Init adc and DMA
+	I2C_Configuration();								//Start the I2C hardware
+	GPIO_Init_OLED();									//Init the GPIO ports for the OLED
+	restoreSettings();									//Load settings
+
+	StartUp_Accelerometer(systemSettings.sensitivity); 	//start the accelerometer
+
+	setupPID(); 										//Init the PID values
+	readIronTemp(systemSettings.tempCalibration, 0,0); 	//load the default calibration value
+	Init_Oled(systemSettings.flipDisplay); 				//Init the OLED display
+
+	OLED_DrawString("VER 1.11", 8); 					//Version Number
+	delayMs(500);										//Pause to show version number
+	Start_Watchdog(1000); 								//start the system watch dog as 1 second timeout
+}
--- a/workspace/ts100/src/Modes.c
+++ b/workspace/ts100/src/Modes.c
@@ -5,46 +5,82 @@
 *      Author: Ralim <ralim@ralimtek.com>
 */
 #include "Modes.h"
+const char *SettingsLongNames[] = { "      Undervoltage Cutout <V>",
+		"      Sleep Temperature <C>", "      Sleep Timeout <Minutes>",
+		"      Shutdown Timeout <Minutes>", "      Motion Detection",
+		"      Motion Sensitivity", "      Temperature Unit",
+		"      Temperature Rounding Amount",
+		"      Temperature Display Update Rate",
+		"      Flip Display for Left Hand",
+		"      Enable front key boost 450C mode when soldering",
+		"      Temperature when in boost mode" };
+const uint8_t SettingsLongNamesLengths[] = { 29, 27, 29, 32, 22, 24, 22, 33, 37,
+		32, 53, 36 };
+uint8_t StatusFlags = 0;
+uint32_t temporaryTempStorage = 0;
 //This does the required processing and state changes
 void ProcessUI() {
 	uint8_t Buttons = getButtons(); //read the buttons status
-
-	if (millis() - getLastButtonPress() < 200)
+	static uint32_t lastModeChange = 0;
+	if (millis() - getLastButtonPress() < 30)
 		Buttons = 0;
-	//rough prevention for debouncing and allocates settling time
-	//OLED_DrawThreeNumber(Buttons, 0);
+	else if (Buttons != 0) {
+		resetLastButtonPress();
+		resetButtons();
+	}
+	//rough prevention for de-bouncing and allocates settling time
+
 	switch (operatingMode) {
 	case STARTUP:
-		if ((millis() - getLastButtonPress() > 1000)) {
-			if (Buttons & BUT_A) {
-				//A key pressed so we are moving to soldering mode
-				operatingMode = SOLDERING;
-				delayMs(500);
-				resetLastButtonPress();
-				resetButtons();
-			} else if (Buttons & BUT_B) {
-				//B Button was pressed so we are moving to the Settings menu
-				operatingMode = SETTINGS;
-				delayMs(500);
-				resetLastButtonPress();
-				resetButtons();
-			}
+		if (Buttons == (BUT_A | BUT_B)) {
+			operatingMode = THERMOMETER;
+		} else if (Buttons == BUT_A) {
+			//A key pressed so we are moving to soldering mode
+			operatingMode = SOLDERING;
+		} else if (Buttons == BUT_B) {
+			//B Button was pressed so we are moving to the Settings menu
+			operatingMode = SETTINGS;
 		}
-		//Nothing else to check here
 		break;
 	case SOLDERING:
 		//We need to check the buttons if we need to jump out
-		if (Buttons & BUT_A) {
-			//A key pressed so we are moving to temp set
+		if ((Buttons == BUT_A && !systemSettings.boostModeEnabled)
+				|| Buttons == BUT_B) {
+			//A or B key pressed so we are moving to temp set
 			operatingMode = TEMP_ADJ;
-			resetLastButtonPress();
-			resetButtons();
-		} else if (Buttons & BUT_B) {
-			//B Button was pressed so we are moving back to idle
-			operatingMode = STARTUP;
-			resetLastButtonPress();
-			resetButtons();
+			if (StatusFlags == 8) {
+				//Boost mode was enabled before
+				//We need to cancel the temp
+				systemSettings.SolderingTemp = temporaryTempStorage;
+				StatusFlags = 0;
+			}
+		} else if (Buttons == (BUT_A | BUT_B)) {
+
+			//Both buttons were pressed, exit back to the cooling screen
+			operatingMode = COOLING;
+			if (StatusFlags == 8) {
+				//Boost mode was enabled before
+				//We need to cancel the temp
+				systemSettings.SolderingTemp = temporaryTempStorage;
+				StatusFlags = 0;
+			}
+
+		} else if ((getRawButtons() == BUT_A && systemSettings.boostModeEnabled)) {
+			if (StatusFlags != 8) {
+				StatusFlags = 8;
+				temporaryTempStorage = systemSettings.SolderingTemp;
+				systemSettings.SolderingTemp = systemSettings.BoostTemp;
+			}
+			//Update the PID Loop
+			int32_t newOutput = computePID(systemSettings.SolderingTemp);
+			setIronTimer(newOutput);
 		} else {
+			if (StatusFlags == 8) {
+				//Boost mode was enabled before
+				//We need to cancel the temp
+				systemSettings.SolderingTemp = temporaryTempStorage;
+				StatusFlags = 0;
+			}
 			//We need to check the timer for movement in case we need to goto idle
 			if (systemSettings.movementEnabled)
 				if (millis() - getLastMovement()
@@ -55,73 +91,117 @@ void ProcessUI() {
 						return;
 					}
 				}
-
-			//If no buttons pushed we need to perform the PID loop for the iron temp
-			int32_t newOutput = computePID(systemSettings.SolderingTemp);
-			if (newOutput >= 0) {
-				setIronTimer(newOutput);
+			uint16_t voltage = readDCVoltage(systemSettings.voltageDiv); //get X10 voltage
+			if ((voltage / 10) < systemSettings.cutoutVoltage) {
+				operatingMode = UVLOWARN;
+				lastModeChange = millis();
 			}
+			//Update the PID Loop
+			int32_t newOutput = computePID(systemSettings.SolderingTemp);
+			setIronTimer(newOutput);
 		}
 		break;
 	case TEMP_ADJ:
-		if (Buttons & BUT_A) {
+		if (Buttons == BUT_A) {
 			//A key pressed so we are moving down in temp
-			resetLastButtonPress();
+
 			if (systemSettings.SolderingTemp > 1000)
 				systemSettings.SolderingTemp -= 100;
-		} else if (Buttons & BUT_B) {
+		} else if (Buttons == BUT_B) {
 			//B key pressed so we are moving up in temp
-			resetLastButtonPress();
 			if (systemSettings.SolderingTemp < 4500)
 				systemSettings.SolderingTemp += 100;
 		} else {
 			//we check the timeout for how long the buttons have not been pushed
 			//if idle for > 3 seconds then we return to soldering
-			if (millis() - getLastButtonPress() > 3000)
+			//Or if both buttons pressed
+			if ((millis() - getLastButtonPress() > 2000)
+					|| Buttons == (BUT_A | BUT_B)) {
 				operatingMode = SOLDERING;
+				saveSettings();
+			}
 		}
 		break;
 	case SETTINGS:
 		//Settings is the mode with the most logic
 		//Here we are in the menu so we need to increment through the sub menus / increase the value
-		if (millis() - getLastButtonPress() < 400)
-			return;
+		if (StatusFlags == 4 && Buttons != 0) {
+			//The user pressed the button to breakout of the settings help prompt
+			StatusFlags = 0;
+		} else {
+			if (Buttons & BUT_A) {
+				//A key iterates through the menu
+				if (settingsPage == SETTINGSOPTIONSCOUNT) {
+					//Roll off the end
+					settingsPage = 0;				//reset
+					operatingMode = STARTUP;		//reset back to the startup
+					saveSettings();					//Save the settings
+				} else {
+					++settingsPage;					//move to the next option
+				}
+			} else if (Buttons & BUT_B) {
+				//B changes the value selected
+				switch (settingsPage) {
+				case UVCO:
+					//we are incrementing the cutout voltage
+					systemSettings.cutoutVoltage += 1;		//Go up 1V at a jump
+					if (systemSettings.cutoutVoltage > 24)
+						systemSettings.cutoutVoltage = 10;
+					break;
+				case SLEEP_TEMP:
+					systemSettings.SleepTemp += 100;	//Go up 10C at a time
+					if (systemSettings.SleepTemp > 3000)
+						systemSettings.SleepTemp = 1000;//cant sleep higher than 300
+					break;
+				case SLEEP_TIME:
+					++systemSettings.SleepTime;		//Go up 1 minute at a time
+					if (systemSettings.SleepTime > 30)
+						systemSettings.SleepTime = 1;//cant set time over 30 mins
+					//Remember that ^ is the time of no movement
+					break;
+				case SHUTDOWN_TIME:
+					++systemSettings.ShutdownTime;
+					if (systemSettings.ShutdownTime > 60)
+						systemSettings.ShutdownTime = 0;		//wrap to off
+					break;
+				case MOTIONDETECT:
+					systemSettings.movementEnabled =
+							!systemSettings.movementEnabled;
+					break;
+				case TEMPDISPLAY:
+					systemSettings.displayTempInF =
+							!systemSettings.displayTempInF;
+					break;
+				case LEFTY:
+					systemSettings.flipDisplay = !systemSettings.flipDisplay;
+					break;
+				case MOTIONSENSITIVITY:
+					systemSettings.sensitivity++;
+					systemSettings.sensitivity = systemSettings.sensitivity % 3;

-		if (Buttons & BUT_A) {
-			resetLastButtonPress();
-			//A key iterates through the menu
-			if (settingsPage == 2) {
-				//Roll off the end
-				settingsPage = 0;		//reset
-				operatingMode = STARTUP;
-				//TODO Save settings
-			} else
-				++settingsPage;		//move to the next option
-		} else if (Buttons & BUT_B) {
-			resetLastButtonPress();
-			//B changes the value selected
-			switch (settingsPage) {
-			case UVLO:
-				//we are incrementing the cutout voltage
-				systemSettings.cutoutVoltage += 1;		//Go up 1V at a jump
-				if (systemSettings.cutoutVoltage > 24)
-					systemSettings.cutoutVoltage = 9;
-				else if (systemSettings.cutoutVoltage < 9)
-					systemSettings.cutoutVoltage = 9;	//cant set UVLO below 9V
-				break;
-			case SLEEP_TEMP:
-				systemSettings.SleepTemp += 100;		//Go up 10c at a time
-				if (systemSettings.SleepTemp > 3000)
-					systemSettings.SleepTemp = 1000;//cant sleep higher than 300
-				break;
-			case SLEEP_TIME:
-				++systemSettings.SleepTime;		//Go up 1 minute at a time
-				if (systemSettings.SleepTime > 60)
-					systemSettings.SleepTime = 2;	//cant set time over an hour
-				//Remember that ^ is the time of no movement
-				break;
-			default:
-				break;
+					break;
+				case TEMPROUNDING:
+					systemSettings.temperatureRounding++;
+					systemSettings.temperatureRounding =
+							systemSettings.temperatureRounding % 3;
+					break;
+				case DISPUPDATERATE:
+					systemSettings.displayUpdateSpeed++;
+					systemSettings.displayUpdateSpeed =
+							systemSettings.displayUpdateSpeed % 3;
+					break;
+				case BOOSTMODE:
+					systemSettings.boostModeEnabled =
+							!systemSettings.boostModeEnabled;
+					break;
+				case BOOSTTEMP:
+					systemSettings.BoostTemp += 100;	//Go up 10C at a time
+					if (systemSettings.BoostTemp > 4500)
+						systemSettings.BoostTemp = 2500;	//loop back at 250
+					break;
+				default:
+					break;
+				}
 			}
 		}
 		break;
@@ -130,32 +210,164 @@ void ProcessUI() {
 		if (Buttons & BUT_A) {
 			//A Button was pressed so we are moving back to soldering
 			operatingMode = SOLDERING;
-			resetLastButtonPress();
-			resetButtons();
+			Oled_DisplayOn();
 			return;
 		} else if (Buttons & BUT_B) {
 			//B Button was pressed so we are moving back to soldering
 			operatingMode = SOLDERING;
-			resetLastButtonPress();
-			resetButtons();
+			Oled_DisplayOn();
 			return;
 		} else if (systemSettings.movementEnabled)
 			if (millis() - getLastMovement() < 1000) {//moved in the last second
 				operatingMode = SOLDERING; //Goto active mode again
+				Oled_DisplayOn();
 				return;
 			}
+		if (systemSettings.movementEnabled) {
+			//Check if we should shutdown
+			if ((millis() - getLastMovement()
+					> (systemSettings.ShutdownTime * 60000))
+					|| (millis() - getLastButtonPress()
+							> systemSettings.ShutdownTime * 60000)) {
+				operatingMode = COOLING; //shutdown the tip
+				Oled_DisplayOn();
+			}
+		}
 		//else if nothing has been pushed we need to compute the PID to keep the iron at the sleep temp
 		int32_t newOutput = computePID(systemSettings.SleepTemp);
-		if (newOutput >= 0) {
-			setIronTimer(newOutput);
+		setIronTimer(newOutput);
+		break;
+	case COOLING: {
+		setIronTimer(0); //turn off heating
+		//This mode warns the user the iron is still cooling down
+		uint16_t temp = readIronTemp(0, 1, 0xFFFF); //take a new reading as the heater code is not taking new readings
+		if (temp < 400) { //if the temp is < 40C then we can go back to IDLE
+			operatingMode = STARTUP;
+		} else if (Buttons & (BUT_A | BUT_B)) { //we check if the user has pushed a button to ack
+			//Either button was pushed
+			operatingMode = STARTUP;
 		}
+	}
+		break;
+	case UVLOWARN:
+		//We are here if the DC voltage went too low
+		//We want to jump back to IDLE after a bit
+		if (millis() - lastModeChange > 3000) {		//its been 3 seconds
+			operatingMode = STARTUP;		//jump back to idle mode
+		}
+		break;
+	case THERMOMETER: {
+		//This lets the user check the tip temp without heating the iron.. And eventually calibration will be added here
+
+		if (Buttons == BUT_A) {
+			//Single button press, cycle over to the DC display
+			StatusFlags = 0;
+			operatingMode = DCINDISP;
+		} else if (Buttons == BUT_B) {
+			StatusFlags = 0;
+			operatingMode = TEMPCAL;
+		} else if (Buttons == (BUT_A | BUT_B)) {
+			//If the user is holding both button, exit the  screen
+			operatingMode = STARTUP;
+		}
+
+	}
+		break;
+	case DCINDISP: {
+		//This lets the user check the input voltage
+		if (StatusFlags == 0) {
+			if (Buttons == BUT_A) {
+				//Single button press, cycle over to the temp display
+				operatingMode = THERMOMETER;
+			} else if (Buttons == BUT_B) {
+				//dc cal mode
+				StatusFlags = 1;
+			} else if (Buttons == (BUT_A | BUT_B)) {
+				//If the user is holding both button, exit the  screen
+				operatingMode = STARTUP;
+			}
+		} else {
+			//User is calibrating the dc input
+			if (Buttons == BUT_A) {
+				if (!systemSettings.flipDisplay)
+					systemSettings.voltageDiv++;
+				else
+					systemSettings.voltageDiv--;
+			} else if (Buttons == BUT_B) {
+				if (!systemSettings.flipDisplay)
+					systemSettings.voltageDiv--;
+				else
+					systemSettings.voltageDiv++;
+			} else if (Buttons == (BUT_A | BUT_B)) {
+				StatusFlags = 0;
+				saveSettings();
+			}
+			if (systemSettings.voltageDiv < 120)
+				systemSettings.voltageDiv = 160;
+			else if (systemSettings.voltageDiv > 160)
+				systemSettings.voltageDiv = 120;
+		}
+
+	}
+		break;
+	case TEMPCAL: {
+		if (Buttons == BUT_B) {
+			//Single button press, cycle over to the DC IN
+			operatingMode = THERMOMETER;
+		} else if (Buttons == BUT_A) {
+			//Try and calibrate
+			if (StatusFlags == 0) {
+				if ((readTipTemp() < 300) && (readSensorTemp() < 300)) {
+					StatusFlags = 1;
+					systemSettings.tempCalibration = readTipTemp();
+					saveSettings();
+				} else {
+					StatusFlags = 2;
+				}
+			}
+		} else if (Buttons == (BUT_A | BUT_B)) {
+			//If the user is holding both button, exit the  screen
+			operatingMode = STARTUP;
+		}
+
+	}
 		break;
 	default:
 		break;
 	}
 }
+/*
+ * Draws the temp with temp conversion if needed
+ */
+void drawTemp(uint16_t temp, uint8_t x, uint8_t roundingMode) {
+	if (systemSettings.displayTempInF)
+		temp = (temp * 9 + 1600) / 5;/*Convert to F -> T*(9/5)+32*/
+	if (temp % 10 > 5)
+		temp += 10;		//round up
+	temp /= 10;
+	//handle rounding modes
+	if (roundingMode == ROUNDING_FIVE) {
+		if (temp % 10 < 5)
+			temp = (temp / 10) * 10;
+		else
+			temp = ((temp / 10) * 10) + 5;
+	} else if (roundingMode == ROUNDING_TEN) {
+		temp = (temp / 10) * 10;
+	}

+	OLED_DrawThreeNumber(temp, x);
+}
+
+/*
+ * Performs all the OLED drawing for the current operating mode
+ */
 void DrawUI() {
+	static uint32_t lastOLEDDrawTime = 0;
+	static uint16_t lastSolderingDrawnTemp1 = 0;
+	static uint16_t lastSolderingDrawnTemp2 = 0;
+
+	static uint8_t settingsLongTestScrollPos = 0;
+	uint16_t temp = readIronTemp(0, 0, 0xFFFF);
 	switch (operatingMode) {
 	case STARTUP:
 		//We are chilling in the idle mode
@@ -166,27 +378,54 @@ void DrawUI() {
 			Oled_DisplayOff();
 		} else {
 			Oled_DisplayOn();
-			OLED_DrawString("IDLE   ", 7);		//write the word IDLE
+			OLED_DrawIDLELogo();		//Draw the icons for prompting the user
 		}
 		break;
 	case SOLDERING:
 		//The user is soldering
 	{
-		uint16_t temp = readIronTemp(0, 0);
-		if (systemSettings.SolderingTemp + 2 < temp) {
-			OLED_DrawChar('C', 14 * 4);
-		} else {
-			if (getIronTimer() < 500) {
-				OLED_DrawChar(' ', 14 * 4);
-			} else {		//we are heating
-				OLED_DrawChar('H', 14 * 4);
-			}
+		if (systemSettings.displayUpdateSpeed == DISPLAYMODE_SLOW
+				&& (millis() - lastOLEDDrawTime < 200))
+			return;
+		else if (systemSettings.displayUpdateSpeed == DISPLAYMODE_MEDIUM
+				&& (millis() - lastOLEDDrawTime < 100))
+			return;
+		else if (systemSettings.displayUpdateSpeed == DISPLAYMODE_FAST
+				&& (millis() - lastOLEDDrawTime < 50))
+			return;

+		uint32_t tempavg = (temp + lastSolderingDrawnTemp1
+				+ lastSolderingDrawnTemp2);
+		tempavg /= 3;
+		drawTemp(tempavg, 0, systemSettings.temperatureRounding);
+		lastSolderingDrawnTemp1 = temp;
+		lastSolderingDrawnTemp2 = lastSolderingDrawnTemp1;
+		lastOLEDDrawTime = millis();
+		//Now draw symbols
+		if (StatusFlags == 8)
+			OLED_DrawChar('B', 3);
+		else
+			OLED_DrawChar(' ', 3);
+
+		OLED_BlankSlot(6 * 12 + 16, 24 - 16);//blank out the tail after the arrows
+		OLED_BlankSlot(4 * 12 + 16, 24 - 16);//blank out the tail after the temp
+		if (getIronTimer() == 0
+				&& (temp / 10) > (systemSettings.SolderingTemp / 10)) {
+			//Cooling
+			OLED_DrawSymbol(6, 5);
+		} else {
+			if (getIronTimer() < 1500) {
+				//Maintaining
+				OLED_DrawSymbol(6, 7);
+			} else {		//we are heating
+				OLED_DrawSymbol(6, 6);
+			}
+		}
+		if (systemSettings.displayTempInF) {
+			OLED_DrawSymbol(4, 1);
+		} else {
+			OLED_DrawSymbol(4, 0);
 		}
-		OLED_DrawThreeNumber(temp / 10, 0);
-		OLED_DrawChar(' ', 14 * 3);
-		OLED_DrawChar(' ', 14 * 5);
-		OLED_DrawChar(' ', 14 * 6);

 	}
 		break;
@@ -194,44 +433,208 @@ void DrawUI() {
 		//We are prompting the user to change the temp so we draw the current setpoint temp
 		//With the nifty arrows
 		OLED_DrawChar(' ', 0);
-		OLED_DrawThreeNumber(systemSettings.SolderingTemp / 10, 14 * 1);
-		OLED_DrawChar(' ', 14 * 4);
-		OLED_DrawChar(' ', 14 * 5);
-
+		OLED_DrawChar('<', 1);
+		drawTemp(systemSettings.SolderingTemp, 2, 0);
+		OLED_DrawChar(' ', 5);
+		OLED_DrawChar(' ', 7);
+		OLED_DrawChar('>', 6);
 		break;
 	case SETTINGS:
 		//We are prompting the user the setting name
+		if (millis() - getLastButtonPress() > 3000) {
+			StatusFlags = 4;
+			//If the user has idled for > 3 seconds, show the long name for the selected setting instead
+			//draw from settingsLongTestScrollPos through to end of screen
+			uint8_t lengthLeft = SettingsLongNamesLengths[settingsPage]
+					- settingsLongTestScrollPos;
+			if (lengthLeft < 1)
+				settingsLongTestScrollPos = 0;
+			//^ Reset once not much left
+			if (lengthLeft > 8)
+				lengthLeft = 8;
+			OLED_DrawString(
+					SettingsLongNames[(uint8_t) settingsPage]
+							+ settingsLongTestScrollPos, lengthLeft);
+			if (lengthLeft < 8)
+				for (uint8_t i = lengthLeft; i < 8; i++)
+					OLED_DrawChar(' ', i);
+			if (millis() - lastOLEDDrawTime > 120) {
+				settingsLongTestScrollPos++;
+				lastOLEDDrawTime = millis();
+			}
+		} else {
+			settingsLongTestScrollPos = 0;
+			switch (settingsPage) {
+			case UVCO:
+				OLED_DrawString("UVCO ", 5);
+				OLED_DrawTwoNumber(systemSettings.cutoutVoltage, 5);
+				OLED_DrawChar('V', 7);
+				break;
+			case SLEEP_TEMP:
+				OLED_DrawString("STMP ", 5);
+				OLED_DrawThreeNumber(systemSettings.SleepTemp / 10, 5);
+				break;
+			case SLEEP_TIME:
+				OLED_DrawString("SLTME ", 6);
+				OLED_DrawTwoNumber(systemSettings.SleepTime, 6);
+				break;
+			case SHUTDOWN_TIME:
+				OLED_DrawString("SHTME ", 6);
+				OLED_DrawTwoNumber(systemSettings.ShutdownTime, 6);
+				break;
+			case MOTIONDETECT:/*Toggle the mode*/
+				if (systemSettings.movementEnabled)
+					OLED_DrawString("MOTION T", 8);
+				else
+					OLED_DrawString("MOTION F", 8);
+				break;
+			case TEMPDISPLAY:/*Are we showing in C or F ?*/
+				if (systemSettings.displayTempInF)
+					OLED_DrawString("TMPUNT F", 8);
+				else
+					OLED_DrawString("TMPUNT C", 8);
+				break;

-		switch (settingsPage) {
-		case UVLO:
-			OLED_DrawString("UVLO", 4);
-			OLED_DrawTwoNumber(systemSettings.cutoutVoltage, 14 * 4);
-			//OLED_DrawChar('V', 14 * 5);
+			case LEFTY:

-			break;
-		case SLEEP_TEMP:
-			OLED_DrawString("STMP", 4);
-			OLED_DrawThreeNumber(systemSettings.SleepTemp / 10, 14 * 4);
-			//OLED_DrawChar('V', 14 * 5);
+				if (systemSettings.flipDisplay)
+					OLED_DrawString("FLPDSP T", 8);
+				else
+					OLED_DrawString("FLPDSP F", 8);
+				break;
+			case MOTIONSENSITIVITY:
+				switch (systemSettings.sensitivity) {
+				case MOTION_HIGH:
+					OLED_DrawString("SENSE H ", 8);
+					break;
+				case MOTION_MED:
+					OLED_DrawString("SENSE M ", 8);
+					break;
+				case MOTION_LOW:
+					OLED_DrawString("SENSE L ", 8);
+					break;
+				default:
+					OLED_DrawString("SENSE   ", 8);
+					break;
+				}

-			break;
-		case SLEEP_TIME:
-			OLED_DrawString("STME ", 5);
-			OLED_DrawTwoNumber(systemSettings.SleepTime, 14 * 5);
-			break;
-		default:
-			break;
+				break;
+			case TEMPROUNDING:
+				//We are prompting the user about their display mode preferences
+			{
+				switch (systemSettings.temperatureRounding) {
+				case ROUNDING_NONE:
+					OLED_DrawString("TMPRND 1", 8);
+					break;
+				case ROUNDING_FIVE:
+					OLED_DrawString("TMPRND 5", 8);
+					break;
+				case ROUNDING_TEN:
+					OLED_DrawString("TMPRND10", 8);
+					break;
+				default:
+					OLED_DrawString("TMPRND 1", 8);
+					break;
+				}
+			}
+				break;
+			case DISPUPDATERATE:
+				//We are prompting the user about their display mode preferences
+			{
+				switch (systemSettings.displayUpdateSpeed) {
+				case DISPLAYMODE_FAST:
+					OLED_DrawString("TMPSPD F", 8);
+					break;
+				case DISPLAYMODE_SLOW:
+					OLED_DrawString("TMPSPD S", 8);
+					break;
+				case DISPLAYMODE_MEDIUM:
+					OLED_DrawString("TMPSPD M", 8);
+					break;
+
+				}
+			}
+				break;
+			case BOOSTMODE:
+				switch (systemSettings.boostModeEnabled) {
+				case 1:
+					OLED_DrawString("BOOST  T", 8);
+					break;
+				case 0:
+					OLED_DrawString("BOOST  F", 8);
+					break;
+				}
+				break;
+			case BOOSTTEMP:
+				OLED_DrawString("BTMP ", 5);
+				OLED_DrawThreeNumber(systemSettings.BoostTemp / 10, 5);
+				break;
+			default:
+				break;
+			}
 		}
 		break;
 	case SLEEP:
 		//The iron is in sleep temp mode
 		//Draw in temp and sleep
 		OLED_DrawString("SLP", 3);
-		uint16_t temp = readIronTemp(0, 0);
-		OLED_DrawThreeNumber(temp / 10, 14 * 3);
+		drawTemp(temp, 4, systemSettings.temperatureRounding);
+		OLED_BlankSlot(84, 96 - 85);		//blank out after the temp
+
+		if (millis() - getLastMovement() > (10 * 60 * 1000)
+				&& (millis() - getLastButtonPress() > (10 * 60 * 1000))) {
+			//OLED off
+			Oled_DisplayOff();
+		} else {
+			Oled_DisplayOn();
+		}
+
+		break;
+	case COOLING:
+		//We are warning the user the tip is cooling
+		OLED_DrawString("COOL ", 5);
+		drawTemp(temp, 5, systemSettings.temperatureRounding);
+		break;
+	case UVLOWARN:
+		OLED_DrawString("LOW VOLT", 8);
+		break;
+	case THERMOMETER:
+		temp = readIronTemp(0, 1, 0xFFFF);	//Force a reading as heater is off
+		OLED_DrawString("TEMP ", 5);//extra one to it clears the leftover 'L' from IDLE
+		drawTemp(temp, 5, 0);
+		break;
+	case DCINDISP: {
+		uint16_t voltage = readDCVoltage(systemSettings.voltageDiv); //get X10 voltage
+
+		if (StatusFlags == 0 || ((millis() % 1000) > 500)) {
+			OLED_DrawString("IN", 2);
+			OLED_DrawChar((voltage / 100) % 10, 2);
+			voltage -= (voltage / 100) * 100;
+			OLED_DrawChar((voltage / 10) % 10, 3);
+			voltage -= (voltage / 10) * 10;
+			OLED_DrawChar('.', 4);
+			OLED_DrawChar(voltage % 10, 5);
+			OLED_DrawChar('V', 6);
+			OLED_DrawChar(' ', 7);
+		} else {
+			OLED_DrawString("IN      ", 8);
+		}
+	}
+		break;
+	case TEMPCAL: {
+
+		if (StatusFlags == 0) {
+			OLED_DrawString("CAL TEMP", 8);
+		} else if (StatusFlags == 1) {
+			OLED_DrawString("CAL OK  ", 8);
+		} else if (StatusFlags == 2) {
+			OLED_DrawString("CAL FAIL", 8);
+		}
+	}

 		break;
 	default:
 		break;
 	}
+
 }
--- a/workspace/ts100/src/Oled.c
+++ b/workspace/ts100/src/Oled.c
@@ -1,71 +1,92 @@
-/********************* (C) COPYRIGHT 2015 e-Design Co.,Ltd. **********************
- File Name :      Oled.c
- Version :        S100 APP Ver 2.11
- Description:
- Author :         Celery
- Data:            2015/07/07
- History:
- 2015/07/07   ͳһ<CDB3><D2BB><EFBFBD><EFBFBD><EFBFBD><EFBFBD>
- *******************************************************************************/
+/*
+ *
+ * OLED.c
+ * Functions for working with the oled screen.
+ * Writes to the screen using I2C
+ */

 #include <stdio.h>
 #include <string.h>
-#include "APP_Version.h"
+
 #include "Oled.h"
 #include "Bios.h"
 #include "I2C.h"

 #include "Font.h"
+int8_t displayOffset = 32;
+/*Setup params for the OLED screen*/
+/*http://www.displayfuture.com/Display/datasheet/controller/SSD1307.pdf*/
+/*All commands are prefixed with 0x80*/
+u8 OLED_Setup_Array[46] = { 0x80, 0xAE,/*Display off*/
+0x80, 0xD5,/*Set display clock divide ratio / osc freq*/
+0x80, 0x52,/*Unknown*/
+0x80, 0xA8,/*Set Multiplex Ratio*/
+0x80, 0x0F, /*16 == max brightness,39==dimmest*/
+0x80, 0xC0,/*Set COM Scan direction*/
+0x80, 0xD3,/*Set Display offset*/
+0x80, 0x00,/*0 Offset*/
+0x80, 0x40,/*Set Display start line to 0*/
+0x80, 0xA0,/*Set Segment remap to normal*/
+0x80, 0x8D,/*Unknown*/
+0x80, 0x14,/*Unknown*/
+0x80, 0xDA,/*Set VCOM Pins hardware config*/
+0x80, 0x02,/*Combination 2*/
+0x80, 0x81,/*Contrast*/
+0x80, 0x33,/*51*/
+0x80, 0xD9,/*Set pre-charge period*/
+0x80, 0xF1,/**/
+0x80, 0xDB,/*Adjust VCOMH regulator ouput*/
+0x80, 0x30,/*Unknown*/
+0x80, 0xA4,/*Enable the display GDDR*/
+0x80, 0XA6,/*Normal display*/
+0x80, 0xAF /*Dispaly on*/
+};

-u8 gOled_param[46] = { 0x80, 0xAE, 0x80, 0xD5, 0x80, 0x52, 0x80, 0xA8, 0x80,
-		0x0f, 0x80, 0xC0, 0x80, 0xD3, 0x80, 0x00, 0x80, 0x40, 0x80, 0xA0, 0x80,
-		0x8D, 0x80, 0x14, 0x80, 0xDA, 0x80, 0x02, 0x80, 0x81, 0x80, 0x33, 0x80,
-		0xD9, 0x80, 0xF1, 0x80, 0xDB, 0x80, 0x30, 0x80, 0xA4, 0x80, 0XA6, 0x80,
-		0xAF };
-
-/*******************************************************************************
-
- *******************************************************************************/
-void Sc_Pt(u8 Co) {
-	u8 pt[4] = { 0x80, 0x81, 0x80, Co };
-
-	I2C_PageWrite(pt, 4, DEVICEADDR_OLED);
-}
-/*******************************************************************************
+/*
 Function: Oled_DisplayOn
 Description:Turn on the Oled display
- *******************************************************************************/
+ */
 void Oled_DisplayOn(void) {
 	u8 data[6] = { 0x80, 0X8D, 0x80, 0X14, 0x80, 0XAF };

 	I2C_PageWrite(data, 6, DEVICEADDR_OLED);
 }
-/*******************************************************************************
+/*
 Function: Oled_DisplayOff
 Description:Turn off the Oled display
- *******************************************************************************/
+ */
 void Oled_DisplayOff(void) {
 	u8 data[6] = { 0x80, 0X8D, 0x80, 0X10, 0x80, 0XAE };

 	I2C_PageWrite(data, 6, DEVICEADDR_OLED);
 }
+/*
+ * This sets the OLED screen to invert the screen (flip it vertically)
+ * This is used if the unit is set to left hand mode
+ */
+void Oled_DisplayFlip() {
+	u8 data[2] = { 0x80, 0XC8 };
+	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
+	data[1] = 0xA1;
+	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
+	displayOffset = 0;

-/*******************************************************************************
- Function: Data_Command
+}
+/*
 Description: write a command to the Oled display
 Input: number of bytes to write, array to write
 Output:
- *******************************************************************************/
-u8* Data_Command(u8 wide, u8* ptr) {
+ */
+u8* Data_Command(u8 length, u8* data) {
 	int i;
-	u8 tx_data[128];
+	u8 tx_data[129];
 	//here are are inserting the data write command at the beginning
 	tx_data[0] = 0x40;
-	wide += 1;
-	for (i = 1; i < wide; i++) //Loop through the array of data
-		tx_data[i] = *ptr++;
-	I2C_PageWrite(tx_data, wide, DEVICEADDR_OLED); //write out the buffer
-	return ptr;
+	length++;
+	for (i = 1; i < length; i++) //Loop through the array of data
+		tx_data[i] = *data++;
+	I2C_PageWrite(tx_data, length, DEVICEADDR_OLED); //write out the buffer
+	return data;
 }
 /*******************************************************************************
 Function:Set_ShowPos
@@ -73,11 +94,10 @@ u8* Data_Command(u8 wide, u8* ptr) {
 Input:x,y co-ordinates
 *******************************************************************************/
 void Set_ShowPos(u8 x, u8 y) {
-	u8 pos_param[8] = { 0x80, 0xB0, 0x80, 0x21, 0x80, 0x20, 0x80, 0x7F };
-
-	pos_param[5] = x + 32;
+	u8 pos_param[8] = { 0x80, 0xB0, 0x80, 0x21, 0x80, 0x00, 0x80, 0x7F };
+	//page 0, start add = x(below) through to 0x7F (aka 127)
+	pos_param[5] = x + displayOffset;/*Display offset ==0 for Lefty, == 32 for righty*/
 	pos_param[1] += y;
-
 	I2C_PageWrite(pos_param, 8, DEVICEADDR_OLED);
 }

@@ -85,7 +105,7 @@ void Set_ShowPos(u8 x, u8 y) {
 Function:Oled_DrawArea
 Description:
 Inputs:(x,y) start point, (width,height) of enclosing rect, pointer to data
- Output: last byte written out
+ Output: pointer to the last byte written out
 *******************************************************************************/
 u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high, u8* ptr) {
 	u8 m, n, y;
@@ -108,20 +128,6 @@ u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high, u8* ptr) {
 	return ptr;
 }

-/*******************************************************************************
- Function:Clean_Char
- Description:Overwries a square to off, used to overwrite a char
- Inputs:(k) input X position char starts at, (wide) how many pixels wide the char is
- *******************************************************************************/
-void Clean_Char(int k, u8 wide) {
-	int i;
-	u8 tx_data[128];
-
-	memset(&tx_data[0], 0, wide);
-	for (i = 0; i < 2; i++) {
-		Oled_DrawArea(k, i * 8, wide, 8, tx_data);
-	}
-}
 /*******************************************************************************
 Function:GPIO_Init_OLED
 Description:Init the outputs as needed for the OLED (in this case the RST line)
@@ -136,17 +142,22 @@ void GPIO_Init_OLED(void) {
 }
 /*******************************************************************************
 Function: Init_Oled
- Description: Initalizes the Oled screen
+ Description: Initializes the Oled screen
 *******************************************************************************/
-void Init_Oled(void) {
+void Init_Oled(uint8_t leftHanded) {
 	u8 param_len;

 	OLED_RST();
-	delayMs(2); //reset the oled
-	OLED_ACT();
-	delayMs(2);
+	delayMs(5);
+	OLED_ACT(); //Toggling reset to reset the oled
+	delayMs(5);
 	param_len = 46;
-	I2C_PageWrite((u8 *) gOled_param, param_len, DEVICEADDR_OLED);
+	if (leftHanded) {
+		OLED_Setup_Array[11] = 0xC8;
+		OLED_Setup_Array[19] = 0xA1;
+		displayOffset = 0;
+	}
+	I2C_PageWrite((u8 *) OLED_Setup_Array, param_len, DEVICEADDR_OLED);
 }

 /*******************************************************************************
@@ -155,54 +166,105 @@ void Init_Oled(void) {
 *******************************************************************************/
 void Clear_Screen(void) {
 	u8 tx_data[128];
-	memset(&tx_data[0], 0, 128);
+	memset(tx_data, 0, 128);
 	for (u8 i = 0; i < 2; i++) {
 		Oled_DrawArea(0, i * 8, 128, 8, tx_data);
 	}
 }
+/*
+ * Draws a string onto the screen starting at the left
+ */
 void OLED_DrawString(char* string, uint8_t length) {
 	for (uint8_t i = 0; i < length; i++) {
-		OLED_DrawChar(string[i], i * 14);
+		OLED_DrawChar(string[i], i);
 	}
 }
-void OLED_DrawChar(char c, uint8_t x) {
-	if ((x) > (128 - 14))
-		return; //Rudimentary clipping to not draw off screen
-	u8* ptr;
-	ptr = (u8*) FONT;
-	if (c >= 'A' && c <= 'Z') {
-		ptr += (c - 'A' + 10) * (14 * 2); //alpha is ofset 10 chars into the array
-	} else if (c >= '0' && c <= '9')
-		ptr += (c - '0') * (14 * 2);
-	else if (c < 10)
-		ptr += (c) * (14 * 2);
-	else if (c == ' ') {
-		//blank on space bar
-		ptr += (36) * (14 * 2);
-	}
-
-	Oled_DrawArea(x, 0, 14, 16, (u8*) ptr);
-}
 /*
- * Draw a 2 digit number to the display
- * */
-void OLED_DrawTwoNumber(uint8_t in, uint8_t x) {
-	OLED_DrawChar((in / 10)%10, x);
-	OLED_DrawChar(in % 10, x + 14);
+ * Draw a char onscreen at letter index x
+ */
+void OLED_DrawChar(char c, uint8_t x) {
+	if (x > 7)
+		return; //clipping
+	x *= FONT_WIDTH; //convert to a x coordinate
+
+	u8* ptr = (u8*) FONT;
+	if (c >= 'a' && c <= 'z') {
+		ptr += (c - 'a' + 10) * (FONT_WIDTH * 2); //alpha is ofset 10 chars into the array
+	} else if (c >= 'A' && c <= 'Z') {
+		ptr += (c - 'A' + 10) * (FONT_WIDTH * 2); //alpha is ofset 10 chars into the array
+	} else if (c >= '0' && c <= '9')
+		ptr += (c - '0') * (FONT_WIDTH * 2);
+	else if (c < 10)
+		ptr += (c) * (FONT_WIDTH * 2);
+	else if (c == ' ') {
+		//blank on space bar
+		ptr += (36) * (FONT_WIDTH * 2);
+	} else if (c == '<') {
+		ptr += (37) * (FONT_WIDTH * 2);
+	} else if (c == '>') {
+		ptr += (38) * (FONT_WIDTH * 2);
+	} else if (c == '.') {
+		ptr += (39) * (FONT_WIDTH * 2);
+	}
+
+	Oled_DrawArea(x, 0, FONT_WIDTH, 16, (u8*) ptr);
 }
+
+void OLED_BlankSlot(uint8_t xStart, uint8_t width) {
+	u8* ptr = (u8*) FONT;
+	ptr += (36) * (FONT_WIDTH * 2);
+
+	Oled_DrawArea(xStart, 0, width, 16, (u8*) ptr);
+}
+
+/*
+ * Draw a 2 digit number to the display at letter slot x
+ */
+void OLED_DrawTwoNumber(uint8_t in, uint8_t x) {
+
+	OLED_DrawChar((in / 10) % 10, x);
+	OLED_DrawChar(in % 10, x + 1);
+}
+/*
+ * Draw a 3 digit number to the display at letter slot x
+ */
 void OLED_DrawThreeNumber(uint16_t in, uint8_t x) {

-	OLED_DrawChar((in / 100)%10, x);
-	OLED_DrawChar((in / 10)%10, x + 14);
-	OLED_DrawChar(in % 10, x + 28);
+	OLED_DrawChar((in / 100) % 10, x);
+	OLED_DrawChar((in / 10) % 10, x + 1);
+	OLED_DrawChar(in % 10, x + 2);
 }
+/*
+ * Draw a 4 digit number to the display at letter slot x
+ */
 void OLED_DrawFourNumber(uint16_t in, uint8_t x) {

-	OLED_DrawChar((in / 1000)%10, x);
-	OLED_DrawChar((in / 100)%10, x+14);
-	OLED_DrawChar((in / 10)%10, x + 28);
-	OLED_DrawChar(in % 10, x + 32);
+	OLED_DrawChar((in / 1000) % 10, x);
+	OLED_DrawChar((in / 100) % 10, x + 1);
+	OLED_DrawChar((in / 10) % 10, x + 2);
+	OLED_DrawChar(in % 10, x + 3);
 }

-/******************************** END OF FILE *********************************/
+void OLED_DrawIDLELogo() {
+	static uint8_t drawAttempt = 0;
+	drawAttempt++;
+	if (drawAttempt & 0x80) {
+		if (drawAttempt & 0x08)
+			Oled_DrawArea(0, 0, 96, 8, (u8*) Iron_RightArrow_UP);
+		else
+			Oled_DrawArea(0, 0, 96, 8, (u8*) Iron_RightArrow_DOWN);

+		Oled_DrawArea(0, 8, 96, 8, (u8*) Iron_Base);
+	} else {
+		if (drawAttempt & 0x08)
+			Oled_DrawArea(0, 0, 96, 8, (u8*) Iron_LeftArrow_UP);
+		else
+			Oled_DrawArea(0, 0, 96, 8, (u8*) Iron_LeftArrow_DOWN);
+		Oled_DrawArea(0, 8, 96, 8, (u8*) Iron_Base);
+	}
+
+}
+
+void OLED_DrawSymbol(uint8_t x, uint8_t symbol) {
+	Oled_DrawArea(x * FONT_WIDTH, 0, 16, 16, SymbolTable + (symbol * 32));
+}
--- a/workspace/ts100/src/PID.c
+++ b/workspace/ts100/src/PID.c
@@ -6,40 +6,36 @@
 */

 #include "PID.h"
-#define MAXPIDOUTPUT 500000
-//This funtion computes the new value for the ON time of the system
+#define MAXPIDOUTPUT 50000
+//This function computes the new value for the ON time of the system
 //This is the return value from this function
 int32_t computePID(uint16_t setpoint) {
-	static uint32_t lastSample = 0;
-	 int32_t ITerm = 0;
+	int32_t ITerm = 0;
 	static int16_t lastReading = 0;
-	if (millis() - lastSample > 25) {
-		//only sample every 50 milliseconds
-		uint16_t currentReading = readIronTemp(0,1); //get the current temp of the iron
-		int16_t error = (int16_t)setpoint - (int16_t)currentReading; //calculate the error term
-		ITerm += (pidSettings.ki * error);
-		if (ITerm > MAXPIDOUTPUT)
-			ITerm = MAXPIDOUTPUT;
-		else if (ITerm < 0)
-			ITerm = 0; //cap at 0 since we cant force the iron to cool itself :)
+	uint16_t currentReading = readIronTemp(0, 1,setpoint); //get the current temp of the iron
+	int16_t error = (int16_t) setpoint - (int16_t) currentReading; //calculate the error term
+	ITerm += (pidSettings.ki * error);
+	if (ITerm > MAXPIDOUTPUT/2)
+		ITerm = MAXPIDOUTPUT/2;
+	else if (ITerm < 0)
+		ITerm = 0; //cap at 0 since we cant force the iron to cool itself :)
+
+	int16_t DInput = (currentReading - lastReading); //compute the input to the D term
+	int32_t output = (pidSettings.kp * error) + (ITerm)
+			- (pidSettings.kd * DInput);
+	if (output > MAXPIDOUTPUT)
+		output = MAXPIDOUTPUT;
+	else if (output < 0)
+		output = 0;
+
+	lastReading = currentReading; //storing values for next iteration of the loop
+	return output;

-		int16_t DInput = (currentReading - lastReading); //compute the input to the D term
-		int32_t output = (pidSettings.kp * error) + (ITerm)
-				- (pidSettings.kd * DInput);
-		if (output > MAXPIDOUTPUT)
-			output = MAXPIDOUTPUT;
-		else if (output < 0)
-			output = 0;
-		lastSample = millis();
-		lastReading = currentReading; //storing values for next iteration of the loop
-		return output;
-	}
-	return -1; //called too fast
 }
-
+/*Sets up the pid values*/
 void setupPID(void) {
-	pidSettings.kp = 22;
-	pidSettings.ki = 7;
-	pidSettings.kd = 2;
+	pidSettings.kp = 15;
+	pidSettings.ki = 2;
+	pidSettings.kd = 3;

 }
--- a/workspace/ts100/src/Settings.c
+++ b/workspace/ts100/src/Settings.c
@@ -0,0 +1,61 @@
+/*
+ * Settings.c
+ *
+ *  Created on: 29 Sep 2016
+ *      Author: Ralim
+ *
+ *      This file holds the users settings and saves / restores them to the devices flash
+ */
+
+#include "Settings.h"
+#define FLASH_ADDR (0x8000000|48896)/*Flash start OR'ed with the maximum amount of flash - 256 bytes*/
+void saveSettings() {
+	//First we erase the flash
+	FLASH_Unlock(); //unlock flash writing
+	FLASH_ClearFlag(FLASH_FLAG_EOP | FLASH_FLAG_PGERR | FLASH_FLAG_WRPRTERR);
+	while (FLASH_ErasePage(FLASH_ADDR) != FLASH_COMPLETE)
+		; //wait for it
+	//erased the chunk
+	//now we program it
+	uint16_t *data = (uint16_t*) &systemSettings;
+	for (uint8_t i = 0; i < (sizeof(systemSettings) / 2); i++) {
+		FLASH_ProgramHalfWord(FLASH_ADDR + (i * 2), data[i]);
+	}
+}
+
+void restoreSettings() {
+	//We read the flash
+	uint16_t *data = (uint16_t*) &systemSettings;
+	for (uint8_t i = 0; i < (sizeof(systemSettings) / 2); i++) {
+		data[i] = *(uint16_t *) (FLASH_ADDR + (i * 2));
+	}
+	//if the version is correct were done
+	//if not we reset and save
+	if (systemSettings.version != SETTINGSVERSION) {
+		//probably not setup
+		resetSettings();
+		saveSettings();
+	}
+
+}
+
+void resetSettings() {
+
+	systemSettings.SleepTemp = 1500;			//Temperature the iron sleeps at - default 150.0 C
+	systemSettings.SleepTime = 1;				//How many minutes we wait until going to sleep - default 1 min
+	systemSettings.SolderingTemp = 3200;		//Default soldering temp is 320.0 C
+	systemSettings.movementEnabled = 1; 		//we use movement detection by default
+	systemSettings.cutoutVoltage = 10;			//10V is the minium cutout voltage as the unit V measurement is unstable below 9.5V
+	systemSettings.version = SETTINGSVERSION;	//Store the version number to allow for easier upgrades
+	systemSettings.displayTempInF =0;			//default to C
+	systemSettings.flipDisplay=0;				//Default to right handed mode
+	systemSettings.sensitivity=0x00;			//Default high sensitivity
+	systemSettings.tempCalibration=239;			//Default to their calibration value
+	systemSettings.voltageDiv=144;				//Default divider from schematic
+	systemSettings.ShutdownTime=30;				//How many minutes until the unit turns itself off
+	systemSettings.displayUpdateSpeed=1;		//How fast the LCD updates
+	systemSettings.temperatureRounding=0;		//How the temperature is rounded off
+	systemSettings.boostModeEnabled=0;			//Default to safe, with no boost mode
+	systemSettings.BoostTemp=4000;				//default to 400C
+}
+
--- a/workspace/ts100/ts100.xml
+++ b/workspace/ts100/ts100.xml
@@ -1,9 +1,19 @@
-<?xml version="1.0" encoding="UTF-8" standalone="no"?>
-<targetDefinitions xmlns="http://openstm32.org/stm32TargetDefinitions" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://openstm32.org/stm32TargetDefinitions stm32TargetDefinitions.xsd">
+<?xml version="1.0" encoding="UTF-8"?>
+<!DOCTYPE targetDefinitions [ 
+	<!ELEMENT targetDefinitions (board)>
+	<!ELEMENT board (name, dbgIF+, dbgDEV, mcuId)>
+	<!ELEMENT name (#PCDATA)>
+	<!ELEMENT dbgIF (#PCDATA)>
+	<!ELEMENT dbgDEV (#PCDATA)>
+	<!ELEMENT mcuId (#PCDATA)>
+	<!ATTLIST board id CDATA #REQUIRED>
+]>
+
+<targetDefinitions>
  <board id="ts100">
    <name>ts100</name>
-    <mcuId>stm32f103t8ux</mcuId>
    <dbgIF>SWD</dbgIF>
-    <dbgDEV>ST-LinkV2</dbgDEV>
+    <dbgDEV>ST-Link</dbgDEV>
+    <mcuId>stm32f103t8ux</mcuId>
  </board>
 </targetDefinitions>
Author	SHA1	Message	Date
Ben V. Brown	54356d53a9	Update README.md	2017-07-08 23:26:41 +10:00
Ben V. Brown	d536fb33de	V1.11 - Adding a Boost mode Allows users to enable a boost mode. This allows you to hold down the button near the tip while soldering to temporarily boost the soldering temperature. Closes #10	2017-07-08 23:16:02 +10:00
Ben V. Brown	fa717b2741	Inital work on boost mode	2017-07-08 22:36:49 +10:00
Ben V. Brown	0a7b6145af	V1.10.2 Closes #16 Fixes pressing a button to exit the settings prompts	2017-07-08 18:12:28 +10:00
Ben V. Brown	7b4f467eec	Increase pre PID filtering, reducing display flicker Also improve movement sensitivities to be less extreme ramp up	2017-07-07 23:22:20 +10:00
Ben V. Brown	f72fc36427	Update README.md	2017-07-07 22:23:05 +10:00
Ben V. Brown	3c6151385f	Update display speeds and rounding	2017-07-07 21:31:08 +10:00
Ben V. Brown	03f063cbf2	Add short summary messages for settings	2017-07-07 20:48:03 +10:00
Ben V. Brown	a9e9fb63bf	Update README.md	2017-07-07 19:41:37 +10:00
Ben V. Brown	6bbade318d	Fix default settings for displaymode to fast	2017-07-07 19:29:15 +10:00
Ben V. Brown	f3156e88dc	V1.09 - Add display update mode Adds the following modes for display update: Fast (old style) Slow (1Hz) Rounded (Only shows to 10C increments) None (No temp, just symbol)	2017-07-07 19:20:52 +10:00
Ben V. Brown	13603d8db6	Update README.md	2017-06-17 15:47:15 +10:00
Ben V. Brown	551853360c	Tested bugfix for menu count being wrong	2017-06-09 21:15:53 +10:00
Adriano	711a3e9182	Update Settings.h (#8 ) Options are 7 now. Fix options menu not showing last option	2017-06-09 21:08:01 +10:00
Ben V. Brown	7e1e81cc6f	Adds automatic shutdown Closes #7 . Adds shutdown feature with settings entry	2017-05-29 11:07:45 +10:00
Ben V. Brown	a01cb7a4be	Update README.md	2017-05-28 20:16:00 +10:00
Ben V. Brown	cb5d4bc49d	Import up/down indicator from miniware Closes #3 with nicer heating display	2017-05-21 23:50:26 +10:00
Ben V. Brown	67e3c44f54	Update README.md	2017-05-21 17:42:58 +10:00
Ben V. Brown	e47753d5ab	Update README.md	2017-05-19 11:55:18 +10:00
Ben V. Brown	07d9b15ecc	Update README.md Add note on v1.05	2017-05-19 00:02:00 +10:00
Ben V. Brown	1522c419cf	Add ability to calibrate input DC voltage reading, V1.05 Closes #5	2017-05-18 23:58:39 +10:00
Ben V. Brown	ddedd9ad4f	Update README.md	2017-05-18 23:34:01 +10:00
Ben V. Brown	0f3bb4c356	Bump version 1.04	2017-05-18 21:20:57 +10:00
Ben V. Brown	0ebaab5847	Add more intuitive idle screen with prompts	2017-05-18 21:20:26 +10:00
Ben V. Brown	203a7c154b	Add official Schematic	2017-05-18 19:51:55 +10:00
Ben V. Brown	ebfe457f65	Add Temperature calibration, improve temp accuracy	2017-05-18 19:51:47 +10:00
Ben V. Brown	8c73aa0de4	Use set/clear logic on buttons	2017-05-17 23:36:53 +10:00
Ben V. Brown	53a1b9b7f4	Add sensitivity selection menu	2017-05-17 22:53:21 +10:00
Ben V. Brown	c9d0d5bdb3	Update Readme, making windows warning bold	2017-05-17 13:37:22 +10:00
Ben V. Brown	4f9e738501	Update Readme to add link to releases page	2017-05-17 12:33:17 +10:00
Ben V. Brown	fcaf909a54	Improve button response times (100ms filter)	2017-05-15 23:19:56 +10:00
Ben V. Brown	9b51750a1d	Backend work for supporting adjusting movement sensitivity	2017-05-15 23:00:42 +10:00
Ben V. Brown	fceb81287e	Patch to fix left handed screen	2017-01-23 20:52:46 +11:00
Ben V. Brown	c3d8d246dc	Update readme	2017-01-23 19:45:23 +11:00
Ben V. Brown	1f7cdf9694	For temperature mode force reading	2017-01-23 19:39:56 +11:00
Ben V. Brown	b2db129ab8	V1.02 Add Thermometer Mode	2017-01-23 19:33:03 +11:00
Ben V. Brown	b7e4249d2e	Use both buttons to exit soldering instead of B	2017-01-22 21:19:26 +11:00
Ben V. Brown	0bbdda5b55	Add FlipDisplay, Fahrenheit, Better Font	2016-10-03 19:01:57 +11:00
Ben V. Brown	acb97f1d46	Documentation Updates Update documentation to include menu flow diagram from my website. Remove old firmware version as it is no longer relivant. Remove System Design as it is complete.	2016-10-03 01:18:23 +11:00
Ben V. Brown	0b26e669af	Merge Dev into mainline (#1 ) * Removing USB Need to refine the drive to the iron tip * Update README.md * * Rewrite all code from scratch * Only kept settings * New font * New PID * New Menus * Use Hardware I2C * Faster System * Better Heating Time * No USB * Full Menu System	2016-09-30 00:27:55 +10:00