sv/Marlin
1
1
Fork 0
Code Issues Pull Requests Wiki Activity

tweaks

Browse Source
This commit is contained in:
efflicto
2023-12-26 22:59:12 +01:00
committed by Sven Soost
parent 1b742e6e01
commit 1ea8481194
2 changed files with 21 additions and 21 deletions
Download Patch File Download Diff File Expand all files Collapse all files

30
Marlin/Configuration.h
View File

@@ -536,7 +536,7 @@
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
*
*/
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_0 5
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
@@ -619,7 +619,7 @@
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
// (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275
#define HEATER_0_MAXTEMP 300
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
@@ -627,7 +627,7 @@
#define HEATER_5_MAXTEMP 275
#define HEATER_6_MAXTEMP 275
#define HEATER_7_MAXTEMP 275
#define BED_MAXTEMP 80
#define BED_MAXTEMP 100
#define CHAMBER_MAXTEMP 60
/**
@@ -667,9 +667,9 @@
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
#else
#define DEFAULT_Kp 29.19
#define DEFAULT_Ki 3.15
#define DEFAULT_Kd 67.73
#define DEFAULT_Kp 31.47
#define DEFAULT_Ki 3.33
#define DEFAULT_Kd 74.26
#endif
#endif
@@ -752,9 +752,9 @@
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 53.46
#define DEFAULT_bedKi 7.77
#define DEFAULT_bedKd 245.18
#define DEFAULT_bedKp 81.28
#define DEFAULT_bedKi 15.88
#define DEFAULT_bedKd 277.45
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#endif // PIDTEMPBED
@@ -1175,7 +1175,7 @@
* Override with M203
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
#define DEFAULT_MAX_FEEDRATE { 500, 500, 20, 25 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -1483,17 +1483,17 @@
* | [-] |
* O-- FRONT --+
*/
#define NOZZLE_TO_PROBE_OFFSET { -38.00, -10.00, -0.9 }
#define NOZZLE_TO_PROBE_OFFSET { -33.50, -7.50, -2.035 }
// Most probes should stay away from the edges of the bed, but
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define PROBING_MARGIN 15
// X and Y axis travel speed (mm/min) between probes
#define XY_PROBE_FEEDRATE (133*60)
#define XY_PROBE_FEEDRATE (150*60)
// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
#define Z_PROBE_FEEDRATE_FAST (4*60)
#define Z_PROBE_FEEDRATE_FAST (20*60)
// Feedrate (mm/min) for the "accurate" probe of each point
#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
@@ -1561,7 +1561,7 @@
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
*/
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
//#define Z_AFTER_PROBING 5 // Z position after probing is done
@@ -2098,7 +2098,7 @@
#endif
// Homing speeds (linear=mm/min, rotational=°/min)
#define HOMING_FEEDRATE_MM_M { (40*60), (40*60), (4*60) }
#define HOMING_FEEDRATE_MM_M { (150*60), (150*60), (10*60) }
// Validate that endstops are triggered on homing moves
#define VALIDATE_HOMING_ENDSTOPS

12
Marlin/Configuration_adv.h
View File

@@ -561,7 +561,7 @@
* gets it spinning reliably for a short time before setting the requested speed.
* (Does not work on Sanguinololu with FAN_SOFT_PWM.)
*/
#define FAN_KICKSTART_TIME 1000 // (ms)
#define FAN_KICKSTART_TIME 3000 // (ms)
#define FAN_KICKSTART_POWER 255 // 64-255
// Some coolers may require a non-zero "off" state.
@@ -579,8 +579,8 @@
*
* Define one or both of these to override the default 0-255 range.
*/
//#define FAN_MIN_PWM 50
//#define FAN_MAX_PWM 128
#define FAN_MIN_PWM 64
#define FAN_MAX_PWM 255
/**
* Fan Fast PWM
@@ -607,7 +607,7 @@
* PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
* USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
*/
#define FAST_PWM_FAN // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
//#define FAST_PWM_FAN // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
#if ENABLED(FAST_PWM_FAN)
//#define FAST_PWM_FAN_FREQUENCY 31400 // Define here to override the defaults below
//#define USE_OCR2A_AS_TOP
@@ -908,7 +908,7 @@
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
#define BLTOUCH_DELAY 300
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
@@ -2079,7 +2079,7 @@
#endif
#endif
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)