Ben V. Brown
d3d8e3d2d5
TS101 ( #1695 )
...
* Refactor I2C_SOFT to new #define
* Stitch in some of TS101
Update ShowStartupWarnings.cpp
Update OLED.hpp
Update stm32f1xx_hal_msp.c
Update Setup.cpp
Update Power.cpp
Update Pins.h
Update configuration.h
Power Muxing
Working dual input Voltage handler
Scan mode required for differing injected channels
Inject both dc readings
Update configuration.h
Update configuration.h
Use htim4 for adc control on TS101
Refactor htim names
Add ADC_TRIGGER
Speed up BB I2C a lil
Update configuration.h
Update startup_stm32f103t8ux.S
Update configuration.h
Add LIS2DH clone
LIS2DH gains another clone
Create tooling to allow mapping accelerometers onto different buses
Update startup_stm32f103t8ux.S
Ensure PD IRQ is pulled up
* Stitch in some of TS101
Update ShowStartupWarnings.cpp
Update OLED.hpp
Update stm32f1xx_hal_msp.c
Update Setup.cpp
Update Power.cpp
Update Pins.h
Update configuration.h
Power Muxing
Working dual input Voltage handler
Scan mode required for differing injected channels
Inject both dc readings
Update configuration.h
Update configuration.h
Use htim4 for adc control on TS101
Refactor htim names
Add ADC_TRIGGER
Speed up BB I2C a lil
Update configuration.h
Update startup_stm32f103t8ux.S
Update configuration.h
Add LIS2DH clone
LIS2DH gains another clone
Create tooling to allow mapping accelerometers onto different buses
Update startup_stm32f103t8ux.S
Ensure PD IRQ is pulled up
Allow toggle which button enters PD debug
* Update Pins.h
* Fix hard coded IRQ Pin
Update stm32f1xx_it.c
* Enable EPR
* Tip resistance measurement
* TS101 is a direct drive tip
Update BSP.cpp
* Add S60 and TS101 to builds
Update push.yml
* Update MOVThread.cpp
* Refactor power menu handler
* Correct prescaler
Forgot to update since I changed the period
* Tune in the timer divider for tip control to make PWM less audible
---------
Co-authored-by: discip <53649486+discip@users.noreply.github.com >
2023-06-18 21:58:20 +10:00
Ivan Zorin
a1b9e40f67
Show power source type on detailed screen in soldering mode ( #1708 ) ( #1709 )
...
* Show power source type on detailed screen in soldering mode (#1708 )
* Update according to code review
2023-06-18 21:38:26 +10:00
Ben V. Brown
313336b61f
Swap OLED offset write to reduce glitching
...
@discip
2023-06-18 14:22:08 +10:00
Ben V. Brown
286afad919
S60 Support ( #1692 )
...
* Mock S60
* cleanup
* Start refactor of OLED init
* Setup timers roughly
* Set Vector table offset correctly
Update system_stm32f1xx.c
* Update OLED.cpp
* Update stm32f1xx_hal_msp.c
* Update configuration.h
* I2C init before GPIO
From Errata
Update stm32f1xx_hal_msp.c
Update Software_I2C.h
Allow no hardware I2C
* I2C BB run bus unlock at init
* cleanups
* Software I2C for now
* Mildly more graceful Interpolate
* Handle is powered by DC
Update Power.cpp
Update drawPowerSourceIcon.cpp
Update configuration.h
Update Setup.cpp
* Cleanup HomeScreen
* Segment remap oled at init
* Cleanup
* Update MOVThread.cpp
* Fix PWM Init
* Fix adc2 trigger
* Update configs
* Fixup warning
* Saner default config
* Update ThermoModel.cpp
* Util for current@voltage
* Hub238 warning
* Add hub238 handling in power mode
* Update USBPDDebug_FUSB.cpp
* HUSB238 debug
* Hook PSU Limit
* Use wrapping section of GRAM for scroll
Update OLED.hpp
* Update NTC table
* Fix HUB voltage picker
* Cleanup
* Larger tip filter
* Calibrate in a bunch closer
Update ThermoModel.cpp
* Update configuration.h
* Update HUB238.cpp
* Update configuration.h
* Movement Pin
* Update BSP.cpp
* tim2 irq
* Rough timer conversion (adc broken) but movement working
* Fix tim2 start
* Faster base PWM
* Ensure utils grabs config
* Add wattage limiter tolerance for device
* Speed up PWM and enable PWM current limiting
* tune for 12v
* Prevent start until PD done
* Update configuration.h
* Add HUB238 check for have re-negotiated
* Adjust timer to avoid noise when its possible
2023-06-03 20:05:31 +10:00
discip
422b5b7563
unifying ( #1657 )
2023-04-07 23:42:14 +00:00
Samuel Hedrick
9892dd0423
Added VPDO option for disabling PPS/EPR PDOs.
2023-02-19 14:13:50 -06:00
Samuel Hedrick
5265d7b1ac
Fixed USB-PD policy bug.
...
Some PPS chargers that advertise 7 PDOs are affected.
This includes the Samsung EP-TA845 - likely others as well.
2023-02-15 20:50:23 -06:00
Ben V. Brown
4e37c7bea7
Merge branch 'dev' into BLE
2023-01-23 17:22:06 +11:00
Ben V. Brown
05628daba2
Merge branch 'dev' into new-translations-format
2023-01-22 22:05:13 +11:00
Ben V. Brown
7c8664fb22
Merge branch 'dev' into BLE
2022-12-28 14:24:49 +11:00
Ben V. Brown
afb7628983
FIXUP! Bugfix auto fontstyle
2022-12-11 13:52:43 +11:00
discip
e8cac79923
removed some redundant lines
2022-12-08 00:47:31 +01:00
Ben V. Brown
e9a28c3671
Unify more of the font generation logic between both paths and coalesce all fonts
2022-12-05 22:26:03 +11:00
Ben V. Brown
fdc31467aa
Use size encoded symbols
...
Update make_translation.py
2022-12-05 22:26:03 +11:00
Ben V. Brown
6ca5f5c08d
Merge branch 'dev' into refactor-gui-files
2022-11-25 21:24:49 +11:00
Ben V. Brown
6cbb01db41
References
2022-11-22 18:26:16 +11:00
Ben V. Brown
d0ed30ecb6
Split display checksum out
2022-11-20 21:16:38 +11:00
Ben V. Brown
3e66648768
Force full redraw on rotate
2022-11-20 18:43:43 +11:00
Ben V. Brown
80e7ab3161
Force delay after display state change
...
So that we backoff if OLED is busy
Update OLED.hpp
2022-11-06 22:53:43 +11:00
Ben V. Brown
7eb9f3f10d
Only send on display change
2022-11-06 22:10:09 +11:00
Ben V. Brown
19a6e169a7
Update PD for better EPR compatibility
2022-09-07 18:22:52 +10:00
Ben V. Brown
1fbcdcdf98
Pinecil V2 ( #1341 )
...
* Add SDK
* fork
* massaging makefile
* Drop git module
* Bring in sdk as its broken
Far, Far to much crap to fix with regex now
* Remove bl706
* rf_para_flash_t is missing defs
* Remove crapton of junk
* Remove yet more
* Poking I2C
* Update peripheral_config.h
* Update pinmux_config.h
* Update preRTOS.cpp
* Update main.hpp
* Setup template
* Verbose boot
* I2C ish
* Update I2C_Wrapper.cpp
* Update main.cpp
* Turn off I2C reading for now
* Display running
* Roughing out scheduling timer0
* Starting ADC setup
* Working scheduling of ADC 🎉
* Format adc headers
* Update IRQ.cpp
* Buttons working
* Slow down I2C
* Poking IRQ
* Larger stack required
* Accel on
* Trying to chase down why __libc_init_array isnt working yet
* Working c++
* Cleanup
* Bump stacks
* I2C wake part workaround
* Cleanup
* Working PWM init
* qc draft
* Hookup PWM
* Stable enough ADC
* ADC timing faster + timer without HAL
* Silence
* Remove boot banner
* Tuning in ADC
* Wake PID after ADC
* Remove unused hal
* Draft flash settings
* Working settings save & restore
* Update to prod model
* Cleanup
* NTC thermistor
* Correct adc gain
* Rough tip resistance progress
* Scratch out resistance awareness of the tip
* better adc settings
* Tweaking ADC
* ADC tweaking
* Make adc range scalable
* Update Dockerfile
* Update configuration.h
* Can read same ADC twice in a row
* ADC Setup
* Update PIDThread.cpp
* Lesser adc backoff
* Update USBPD.h
* Add device ID
* Update BSP_Power.h
* Update BSP.cpp
* DrawHex dynamicLength
* Shorter ID padding
* Show validation code
* tip measurement
* Create access for w0w1
* Expose w0 w1
* Enable debug
* crc32
* Device validation
* wip starting epr
* Logic refactor
* Safer PWM Init
* PD cleanups
* Update bl702_pwm.c
* Update power.cpp
* Update usb-pd
* io
* EPR decode
* Better gui for showing pd specs
* Rough handler for capabilities
* EPR
* Fix > 25V input
* Perform pow step after PPS
* Update BSP.cpp
* Fix timer output
* QC3
* Add tip resistance view
* Hold PD negotiation until detection is done for tip res
* Get Thermal mass
* Tip res =0 protection
* Update PIDThread.cpp
* Update GUIThread.cpp
* Rewrite tip resistance measurement
* Update GUIThread.cpp
* Fix fallback
* Far better tip resistance measurement
* Fix QC 0.6V D-
* Convert the interpolator to int32
* Correct the NTC lookup
* Update BSP.cpp
* Update Setup.cpp
* .
Update configuration #defines
More backported functions
* Update usb-pd
* More missed updates
* Refactor BSP
Magic BSP -> PinecilV2
Pine64 BSP -> Pinecil
Update Makefile
* Add Pinecilv2 to CI
* Pinecil v2 multi-lang
Update push.yml
* Update HallSensor.md
* Update README.md
* Fix wrong prestartcheck default
* Fix logo mapping
* Update Makefile
* Remove unused font block
* Style
* Style
* Remove unused timer funcs
* More culling TS80P
* Revert "More culling TS80P"
This reverts commit 2078b89be70c693a89cc
2022-08-19 15:39:37 +10:00
Ben V. Brown
7fcd2b7c5b
Animation non block ( #1347 )
...
* Buttons cancel animation
* Button cancels transition
* Update OLED.cpp
2022-08-12 10:36:10 +10:00
discip
e43449011e
solves artifacts issue if .gif is exactly 1024 B ( #1362 )
...
* solves artifacts issue if .gif is exactly 1024 B
solves https://github.com/Ralim/IronOS-Meta/issues/18
* increased animation speed a tad
2022-08-10 10:16:05 +10:00
Ben V. Brown
f1ceb0ec62
Merge branch 'dev' into pd-epr
2022-07-25 17:34:13 +10:00
Ben V. Brown
081290d6be
Merge branch 'dev' into ticktype
2022-07-25 17:00:34 +10:00
Ben V. Brown
dd239375b1
All Ticks as the right TickType
...
Update usb-pd
2022-07-25 16:45:29 +10:00
nyanpasu64
06e3ca59ea
Fix button presses between short and long being ignored entirely
2022-07-24 15:34:39 -07:00
nyanpasu64
c855f4cffe
Don't send short-presses after releasing long-presses
2022-07-24 15:16:11 -07:00
nyanpasu64
6d6f42d242
Cleanup getButtonState()
2022-07-24 15:12:27 -07:00
Ben V. Brown
c89a6d855c
Update usb-pd
2022-07-19 20:58:47 +10:00
Ben V. Brown
77af6223a4
Merge in draft EPR
2022-07-18 22:58:01 +10:00
Ben V. Brown
0590f9b3f8
Update usb-pd
2022-07-18 22:55:01 +10:00
Ben V. Brown
078b8f5626
DeviceID ( #1314 )
...
* Ability to print hex
* Add device ID getter
* Refactor debug menu
* No longer need patch
* Update make_translation.py
* Fix typo
* Fix hex drawing
2022-06-16 21:39:53 +10:00
Ben V. Brown
f5cb42c9d7
Infinite logo ( #1309 )
...
* Check for button timeout of infinite
* Dedupe
* Alpine bump
2022-06-16 20:21:30 +10:00
discip
9ec92298f3
Update Font.h
2022-05-04 00:17:34 +02:00
Ben V. Brown
a73f634cff
Pinecil pd tweaking ( #1272 )
...
* Raise PD max to 21V
* gui -> settingsGUI
* VBus probe cache
* Rough pass PD capabilities display
* Cleanup build errors
* PD Debug menu working
* Update make_translation.py
* settingsGUI
* Update GUIThread.cpp
* Nicer debug prints
* Show VBus in PD debug
* Update GUIThread.cpp
* Update make_translation.py
* Add docs
* Build tweaks for TS80P 😢
* Show PPS ranges
2022-04-03 12:58:07 +10:00
Ben V. Brown
787bc46bdc
SC7A20 tweaks ( #1251 )
...
* Clean up handling of addresses
* Update SC7A20.hpp
* Try remapped Accel readings
* Fake LIS setup?
* Refining build options
2022-04-03 12:37:27 +10:00
discip
0b8192b690
Bootup logo settings ( #1241 )
...
Adds ability to adjust the time shown for the bootup logo.
2022-04-02 12:39:14 +11:00
Ben V. Brown
232009bf54
Logo rework ( #1232 )
...
!Allows for new logo format that supports animation!
Also moves logos out of repo into their own repo for ease of management.
Changes:
* Remove deprecated logos
* Draft new Bootloader decoder
* Use new logo handler
* Simplify logo code further
* Fix time bug on static images
* Fix exit at end of animation
* Docs
* Interframe delay in 5ms increments
* Quick pass handling empty updates
* Exit at the end _after_ the frame delay
* One final delay
* Fix for overrun of logo data
* Fixes https://github.com/Ralim/IronOS-Meta/issues/7
2022-03-14 09:08:05 +11:00
Ben V. Brown
3747d22773
Flip SC7
2022-02-12 11:30:03 +11:00
Ben V. Brown
730f7cf415
SC7A20 handle address
2022-02-12 11:13:41 +11:00
Ben V. Brown
ba119007ff
Step 1: make LIS2DH12 driver stricter
2022-02-12 11:04:28 +11:00
Ben V. Brown
1969d860c7
Update USBPD.cpp
2022-02-06 14:41:52 +11:00
Ben V. Brown
a2918ae8a4
Update usb-pd
2022-02-06 14:41:49 +11:00
Ben V. Brown
3c83b59b53
Expose Vbus
2022-02-06 13:14:53 +11:00
Ben V. Brown
49c80d2d3f
Update OLED.hpp
2022-02-05 12:39:40 +11:00
Ben V. Brown
80acf58b43
Update OLED.hpp
2022-02-05 12:37:41 +11:00
Ben V. Brown
15763dd55b
Cleanup OLED_FLIP logic
...
Update OLED.hpp
Update OLED.hpp
Update OLED.hpp
2022-02-05 12:23:51 +11:00
discip
c02628f5bf
Update Font.h
2022-01-19 23:51:46 +01:00
