chagnes and tweaks, enabled BL
This commit is contained in:
efflicto
@@ -78,7 +78,7 @@
|
||||
#define SHOW_BOOTSCREEN
|
||||
|
||||
// Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
//#define SHOW_CUSTOM_BOOTSCREEN
|
||||
#define SHOW_CUSTOM_BOOTSCREEN
|
||||
|
||||
// Show the bitmap in Marlin/_Statusscreen.h on the status screen.
|
||||
//#define CUSTOM_STATUS_SCREEN_IMAGE
|
||||
@@ -1073,7 +1073,7 @@
|
||||
//#define ENDSTOPPULLUP_UMAX
|
||||
//#define ENDSTOPPULLUP_VMAX
|
||||
//#define ENDSTOPPULLUP_WMAX
|
||||
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
#endif
|
||||
|
||||
// Enable pulldown for all endstops to prevent a floating state
|
||||
@@ -1274,7 +1274,7 @@
|
||||
* The probe replaces the Z-MIN endstop and is used for Z homing.
|
||||
* (Automatically enables USE_PROBE_FOR_Z_HOMING.)
|
||||
*/
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
// Force the use of the probe for Z-axis homing
|
||||
//#define USE_PROBE_FOR_Z_HOMING
|
||||
@@ -1294,7 +1294,7 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*/
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
#define Z_MIN_PROBE_PIN PC14 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
@@ -1331,7 +1331,7 @@
|
||||
/**
|
||||
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
|
||||
*/
|
||||
//#define BLTOUCH
|
||||
#define BLTOUCH
|
||||
|
||||
/**
|
||||
* MagLev V4 probe by MDD
|
||||
@@ -1483,7 +1483,7 @@
|
||||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -37.00, -12.00, 0 }
|
||||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
@@ -1694,8 +1694,8 @@
|
||||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 220
|
||||
#define Y_BED_SIZE 220
|
||||
#define X_BED_SIZE 230
|
||||
#define Y_BED_SIZE 230
|
||||
|
||||
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
@@ -1873,22 +1873,22 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define MESH_BED_LEVELING
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable one of
|
||||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define ENABLE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
* Auto-leveling needs preheating
|
||||
*/
|
||||
//#define PREHEAT_BEFORE_LEVELING
|
||||
#define PREHEAT_BEFORE_LEVELING
|
||||
#if ENABLED(PREHEAT_BEFORE_LEVELING)
|
||||
#define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
|
||||
#define LEVELING_BED_TEMP 50
|
||||
@@ -1937,7 +1937,7 @@
|
||||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
|
||||
@@ -1953,7 +1953,7 @@
|
||||
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_X 6
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Probe along the Y axis, advancing X after each column
|
||||
@@ -1963,7 +1963,7 @@
|
||||
|
||||
// Beyond the probed grid, continue the implied tilt?
|
||||
// Default is to maintain the height of the nearest edge.
|
||||
//#define EXTRAPOLATE_BEYOND_GRID
|
||||
#define EXTRAPOLATE_BEYOND_GRID
|
||||
|
||||
//
|
||||
// Experimental Subdivision of the grid by Catmull-Rom method.
|
||||
@@ -1983,10 +1983,10 @@
|
||||
//========================= Unified Bed Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 6 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define MESH_INSET 35 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
|
||||
@@ -1997,7 +1997,7 @@
|
||||
//#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
|
||||
// as the Z-Height correction value.
|
||||
|
||||
//#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
|
||||
#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
|
||||
|
||||
#elif ENABLED(MESH_BED_LEVELING)
|
||||
|
||||
|
||||
@@ -908,7 +908,7 @@
|
||||
|
||||
// Safety: The probe needs time to recognize the command.
|
||||
// Minimum command delay (ms). Enable and increase if needed.
|
||||
//#define BLTOUCH_DELAY 500
|
||||
#define BLTOUCH_DELAY 500
|
||||
|
||||
/**
|
||||
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
|
||||
@@ -934,7 +934,7 @@
|
||||
* differs, a mode set eeprom write will be completed at initialization.
|
||||
* Use the option below to force an eeprom write to a V3.1 probe regardless.
|
||||
*/
|
||||
//#define BLTOUCH_SET_5V_MODE
|
||||
#define BLTOUCH_SET_5V_MODE
|
||||
|
||||
/**
|
||||
* Safety: Activate if connecting a probe with an unknown voltage mode.
|
||||
@@ -952,10 +952,10 @@
|
||||
*
|
||||
* Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
|
||||
*/
|
||||
//#define BLTOUCH_HS_MODE true
|
||||
#define BLTOUCH_HS_MODE true
|
||||
|
||||
// Safety: Enable voltage mode settings in the LCD menu.
|
||||
//#define BLTOUCH_LCD_VOLTAGE_MENU
|
||||
#define BLTOUCH_LCD_VOLTAGE_MENU
|
||||
|
||||
#endif // BLTOUCH
|
||||
|
||||
@@ -1719,11 +1719,11 @@
|
||||
//#define CONFIGURATION_EMBEDDING
|
||||
|
||||
// Add an optimized binary file transfer mode, initiated with 'M28 B1'
|
||||
//#define BINARY_FILE_TRANSFER
|
||||
#define BINARY_FILE_TRANSFER
|
||||
|
||||
#if ENABLED(BINARY_FILE_TRANSFER)
|
||||
// Include extra facilities (e.g., 'M20 F') supporting firmware upload via BINARY_FILE_TRANSFER
|
||||
//#define CUSTOM_FIRMWARE_UPLOAD
|
||||
#define CUSTOM_FIRMWARE_UPLOAD
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -2633,7 +2633,7 @@
|
||||
*
|
||||
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
@@ -3661,7 +3661,7 @@
|
||||
//#define M114_REALTIME // Real current position based on forward kinematics
|
||||
//#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
|
||||
|
||||
//#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
|
||||
#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
|
||||
|
||||
// @section gcode
|
||||
|
||||
|
||||
Reference in New Issue
Block a user