mirror of
https://github.com/Ralim/IronOS.git
synced 2025-02-26 07:53:55 +00:00
removed some more redundant entries (#1312)
This commit is contained in:
discip
GitHub
@@ -1,236 +1,208 @@
|
||||
#ifndef CONFIGURATION_H_
|
||||
#define CONFIGURATION_H_
|
||||
#include "Settings.h"
|
||||
#include <stdint.h>
|
||||
/**
|
||||
* Configuration.h
|
||||
* Define here your default pre settings for TS80(P) or TS100
|
||||
*
|
||||
*/
|
||||
#define CONFIGURATION_H_
|
||||
#include "Settings.h"
|
||||
#include <stdint.h>
|
||||
/**
|
||||
* Configuration.h
|
||||
* Define here your default pre settings for TS80(P) or TS100
|
||||
*
|
||||
*/
|
||||
|
||||
//===========================================================================
|
||||
//============================= Default Settings ============================
|
||||
//===========================================================================
|
||||
/**
|
||||
* Default soldering temp is 320.0 C
|
||||
* Temperature the iron sleeps at - default 150.0 C
|
||||
*/
|
||||
//===========================================================================
|
||||
//============================= Default Settings ============================
|
||||
//===========================================================================
|
||||
/**
|
||||
* Default soldering temp is 320.0 C
|
||||
* Temperature the iron sleeps at - default 150.0 C
|
||||
*/
|
||||
|
||||
#define SLEEP_TEMP 150 // Default sleep temperature
|
||||
#define BOOST_TEMP 420 // Default boost temp.
|
||||
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
|
||||
#define SLEEP_TEMP 150 // Default sleep temperature
|
||||
#define BOOST_TEMP 420 // Default boost temp.
|
||||
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
|
||||
|
||||
/**
|
||||
* Blink the temperature on the cooling screen when its > 50C
|
||||
*/
|
||||
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
|
||||
/**
|
||||
* Blink the temperature on the cooling screen when its > 50C
|
||||
*/
|
||||
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
|
||||
|
||||
/**
|
||||
* How many seconds/minutes we wait until going to sleep/shutdown.
|
||||
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
|
||||
*/
|
||||
#define SLEEP_TIME 5 // x10 Seconds
|
||||
#define SHUTDOWN_TIME 10 // Minutes
|
||||
/**
|
||||
* How many seconds/minutes we wait until going to sleep/shutdown.
|
||||
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
|
||||
*/
|
||||
#define SLEEP_TIME 5 // x10 Seconds
|
||||
#define SHUTDOWN_TIME 10 // Minutes
|
||||
|
||||
/**
|
||||
* Auto start off for safety.
|
||||
* Pissible values are:
|
||||
* 0 - none
|
||||
* 1 - Soldering Temperature
|
||||
* 2 - Sleep Temperature
|
||||
* 3 - Sleep Off Temperature
|
||||
*/
|
||||
#define AUTO_START_MODE 0 // Default to none
|
||||
/**
|
||||
* Auto start off for safety.
|
||||
* Pissible values are:
|
||||
* 0 - none
|
||||
* 1 - Soldering Temperature
|
||||
* 2 - Sleep Temperature
|
||||
* 3 - Sleep Off Temperature
|
||||
*/
|
||||
#define AUTO_START_MODE 0 // Default to none
|
||||
|
||||
/**
|
||||
* Locking Mode
|
||||
* When in soldering mode a long press on both keys toggle the lock of the buttons
|
||||
* Possible values are:
|
||||
* 0 - Desactivated
|
||||
* 1 - Lock except boost
|
||||
* 2 - Full lock
|
||||
*/
|
||||
#define LOCKING_MODE 0 // Default to desactivated for safety
|
||||
/**
|
||||
* Locking Mode
|
||||
* When in soldering mode a long press on both keys toggle the lock of the buttons
|
||||
* Possible values are:
|
||||
* 0 - Desactivated
|
||||
* 1 - Lock except boost
|
||||
* 2 - Full lock
|
||||
*/
|
||||
#define LOCKING_MODE 0 // Default to desactivated for safety
|
||||
|
||||
/**
|
||||
* OLED Orientation
|
||||
*
|
||||
*/
|
||||
#define ORIENTATION_MODE 2 // 0: Right 1:Left 2:Automatic - Default Automatic
|
||||
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
|
||||
/**
|
||||
* OLED Orientation
|
||||
*
|
||||
*/
|
||||
#define ORIENTATION_MODE 2 // 0: Right 1:Left 2:Automatic - Default Automatic
|
||||
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
|
||||
|
||||
/**
|
||||
* Temp change settings
|
||||
*/
|
||||
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
|
||||
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
|
||||
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
|
||||
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
|
||||
/**
|
||||
* Temp change settings
|
||||
*/
|
||||
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
|
||||
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
|
||||
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
|
||||
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
|
||||
|
||||
/* Power pulse for keeping power banks awake*/
|
||||
#define POWER_PULSE_INCREMENT 1
|
||||
#define POWER_PULSE_MAX 100 // x10 max watts
|
||||
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
|
||||
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
|
||||
/* Power pulse for keeping power banks awake*/
|
||||
#define POWER_PULSE_INCREMENT 1
|
||||
#define POWER_PULSE_MAX 100 // x10 max watts
|
||||
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
|
||||
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
|
||||
|
||||
#ifdef MODEL_TS100
|
||||
#define POWER_PULSE_DEFAULT 0
|
||||
#else
|
||||
#define POWER_PULSE_DEFAULT 5
|
||||
#endif
|
||||
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
|
||||
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
|
||||
#ifdef MODEL_TS100
|
||||
#define POWER_PULSE_DEFAULT 0
|
||||
#else
|
||||
#define POWER_PULSE_DEFAULT 5
|
||||
#endif
|
||||
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
|
||||
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
|
||||
|
||||
/**
|
||||
* OLED Orientation Sensitivity on Automatic mode!
|
||||
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
|
||||
*/
|
||||
#define SENSITIVITY 7 // Default 7
|
||||
/**
|
||||
* OLED Orientation Sensitivity on Automatic mode!
|
||||
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
|
||||
*/
|
||||
#define SENSITIVITY 7 // Default 7
|
||||
|
||||
/**
|
||||
* Detailed soldering screen
|
||||
* Detailed idle screen (off for first time users)
|
||||
*/
|
||||
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
|
||||
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
|
||||
/**
|
||||
* Detailed soldering screen
|
||||
* Detailed idle screen (off for first time users)
|
||||
*/
|
||||
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
|
||||
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
|
||||
|
||||
#define THERMAL_RUNAWAY_TIME_SEC 20
|
||||
#define THERMAL_RUNAWAY_TEMP_C 10
|
||||
#define THERMAL_RUNAWAY_TIME_SEC 20
|
||||
#define THERMAL_RUNAWAY_TEMP_C 10
|
||||
|
||||
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
|
||||
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
|
||||
#define TEMPERATURE_INF 0 // default to 0
|
||||
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
|
||||
#define ANIMATION_LOOP 1 // 0: off 1: on
|
||||
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
|
||||
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
|
||||
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
|
||||
#define TEMPERATURE_INF 0 // default to 0
|
||||
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
|
||||
#define ANIMATION_LOOP 1 // 0: off 1: on
|
||||
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
|
||||
|
||||
#define OP_AMP_Rf_TS100 750 * 1000 // 750 Kilo-ohms -> From schematic, R1
|
||||
#define OP_AMP_Rin_TS100 2370 // 2.37 Kilo-ohms -> From schematic, R2
|
||||
#define OP_AMP_Rf_TS100 750 * 1000 // 750 Kilo-ohms -> From schematic, R1
|
||||
#define OP_AMP_Rin_TS100 2370 // 2.37 Kilo-ohms -> From schematic, R2
|
||||
|
||||
#define OP_AMP_GAIN_STAGE_TS100 (1 + (OP_AMP_Rf_TS100 / OP_AMP_Rin_TS100))
|
||||
#define OP_AMP_GAIN_STAGE_TS100 (1 + (OP_AMP_Rf_TS100 / OP_AMP_Rin_TS100))
|
||||
|
||||
#define OP_AMP_Rf_TS80 180 * 1000 // 180 Kilo-ohms -> From schematic, R6
|
||||
#define OP_AMP_Rin_TS80 2000 // 2.0 Kilo-ohms -> From schematic, R3
|
||||
#define OP_AMP_Rf_TS80 180 * 1000 // 180 Kilo-ohms -> From schematic, R6
|
||||
#define OP_AMP_Rin_TS80 2000 // 2.0 Kilo-ohms -> From schematic, R3
|
||||
|
||||
#define OP_AMP_GAIN_STAGE_TS80 (1 + (OP_AMP_Rf_TS80 / OP_AMP_Rin_TS80))
|
||||
#define OP_AMP_GAIN_STAGE_TS80 (1 + (OP_AMP_Rf_TS80 / OP_AMP_Rin_TS80))
|
||||
|
||||
// Deriving the Voltage div:
|
||||
// Vin_max = (3.3*(r1+r2))/(r2)
|
||||
// vdiv = (32768*4)/(vin_max*10)
|
||||
// Deriving the Voltage div:
|
||||
// Vin_max = (3.3*(r1+r2))/(r2)
|
||||
// vdiv = (32768*4)/(vin_max*10)
|
||||
|
||||
#if defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) > 1
|
||||
#error "Multiple models defined!"
|
||||
#elif defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) == 0
|
||||
#error "No model defined!"
|
||||
#if defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) > 1
|
||||
#error "Multiple models defined!"
|
||||
#elif defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) == 0
|
||||
#error "No model defined!"
|
||||
#endif
|
||||
|
||||
// Miniware is swapping IMU's around a bit now, so we turn them all on
|
||||
|
||||
#define ACCEL_MMA
|
||||
#define ACCEL_LIS
|
||||
#define ACCEL_SC7
|
||||
#define ACCEL_MSA
|
||||
#define ACCEL_BMA
|
||||
|
||||
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
||||
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
||||
#define PID_TIM_HZ (8) // Tick rate of the PID loop
|
||||
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
||||
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
||||
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
||||
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
||||
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
||||
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
||||
|
||||
#ifdef MODEL_TS100
|
||||
#define VOLTAGE_DIV 467 // 467 - Default divider from schematic
|
||||
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
|
||||
#define PID_POWER_LIMIT 70 // Sets the max pwm power limit
|
||||
#define POWER_LIMIT 0 // 0 watts default limit
|
||||
#define MAX_POWER_LIMIT 70
|
||||
#define POWER_LIMIT_STEPS 5
|
||||
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS100
|
||||
#define TEMP_uV_LOOKUP_HAKKO
|
||||
#define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate
|
||||
|
||||
#define HARDWARE_MAX_WATTAGE_X10 750
|
||||
#define TIP_THERMAL_MASS 65 // X10 watts to raise 1 deg C in 1 second
|
||||
#define TIP_RESISTANCE 75 // x10 ohms, 7.5 typical for ts100 tips
|
||||
|
||||
#define POW_DC
|
||||
#define POW_PD 0
|
||||
#define TEMP_TMP36
|
||||
#endif
|
||||
|
||||
#if defined(MODEL_TS80) + defined(MODEL_TS80P) > 0
|
||||
#define MAX_POWER_LIMIT 40
|
||||
#define POWER_LIMIT_STEPS 2
|
||||
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS80
|
||||
#define TEMP_uV_LOOKUP_TS80
|
||||
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate
|
||||
|
||||
#define TIP_THERMAL_MASS 40
|
||||
#define TIP_RESISTANCE 45 // x10 ohms, 4.5 typical for ts80 tips
|
||||
|
||||
#define LIS_ORI_FLIP
|
||||
#define OLED_FLIP
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80
|
||||
#define VOLTAGE_DIV 780 // Default divider from schematic
|
||||
#define CALIBRATION_OFFSET 900 // the adc offset in uV
|
||||
#define PID_POWER_LIMIT 24 // Sets the max pwm power limit
|
||||
#define POWER_LIMIT 24 // 24 watts default power limit
|
||||
|
||||
#define HARDWARE_MAX_WATTAGE_X10 180
|
||||
|
||||
#define POW_QC
|
||||
#define POW_PD 0
|
||||
#define TEMP_TMP36
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80P
|
||||
#define VOLTAGE_DIV 650 // Default for TS80P with slightly different resistors
|
||||
#define CALIBRATION_OFFSET 1500 // the adc offset in uV
|
||||
#define PID_POWER_LIMIT 35 // Sets the max pwm power limit
|
||||
#define POWER_LIMIT 30 // 30 watts default power limit
|
||||
|
||||
#define HARDWARE_MAX_WATTAGE_X10 300
|
||||
|
||||
#define POW_PD 1
|
||||
#define POW_QC 1
|
||||
#define TEMP_NTC
|
||||
#define I2C_SOFT
|
||||
#define SC7_ORI_FLIP
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// Miniware is swapping IMU's around a bit now, so we turn them all on
|
||||
|
||||
#define ACCEL_MMA
|
||||
#define ACCEL_LIS
|
||||
#define ACCEL_SC7
|
||||
#define ACCEL_MSA
|
||||
#define ACCEL_BMA
|
||||
|
||||
#ifdef MODEL_TS100
|
||||
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
||||
#define VOLTAGE_DIV 467 // 467 - Default divider from schematic
|
||||
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
|
||||
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
||||
#define PID_POWER_LIMIT 70 // Sets the max pwm power limit
|
||||
#define POWER_LIMIT 0 // 0 watts default limit
|
||||
#define MAX_POWER_LIMIT 70 //
|
||||
#define POWER_LIMIT_STEPS 5 //
|
||||
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS100 //
|
||||
#define TEMP_uV_LOOKUP_HAKKO //
|
||||
#define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate
|
||||
#define PID_TIM_HZ (8) // Tick rate of the PID loop
|
||||
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
||||
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
||||
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
||||
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
||||
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
||||
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
||||
#define POW_DC
|
||||
|
||||
#define POW_PD 0
|
||||
|
||||
#define TEMP_TMP36
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80
|
||||
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
||||
#define VOLTAGE_DIV 780 // Default divider from schematic
|
||||
#define PID_POWER_LIMIT 24 // Sets the max pwm power limit
|
||||
#define CALIBRATION_OFFSET 900 // the adc offset in uV
|
||||
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
||||
#define POWER_LIMIT 24 // 24 watts default power limit
|
||||
#define MAX_POWER_LIMIT 40 //
|
||||
#define POWER_LIMIT_STEPS 2 //
|
||||
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS80 //
|
||||
#define TEMP_uV_LOOKUP_TS80 //
|
||||
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate
|
||||
#define PID_TIM_HZ (8) // Tick rate of the PID loop
|
||||
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
||||
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
||||
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
||||
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
||||
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
||||
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
||||
|
||||
#define POW_QC
|
||||
#define POW_PD 0
|
||||
#define TEMP_TMP36
|
||||
#define LIS_ORI_FLIP
|
||||
#define OLED_FLIP
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80P
|
||||
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
||||
#define VOLTAGE_DIV 650 // Default for TS80P with slightly different resistors
|
||||
#define PID_POWER_LIMIT 35 // Sets the max pwm power limit
|
||||
#define CALIBRATION_OFFSET 1500 // the adc offset in uV
|
||||
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
||||
#define POWER_LIMIT 30 // 30 watts default power limit
|
||||
#define MAX_POWER_LIMIT 40 //
|
||||
#define POWER_LIMIT_STEPS 2 //
|
||||
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS80 //
|
||||
#define TEMP_uV_LOOKUP_TS80 //
|
||||
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate
|
||||
#define PID_TIM_HZ (8) // Tick rate of the PID loop
|
||||
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
||||
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
||||
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
||||
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
||||
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
||||
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
||||
|
||||
#define POW_PD 1
|
||||
#define POW_QC 1
|
||||
#define TEMP_NTC
|
||||
#define I2C_SOFT
|
||||
#define LIS_ORI_FLIP
|
||||
#define SC7_ORI_FLIP
|
||||
#define OLED_FLIP
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS100
|
||||
#define HARDWARE_MAX_WATTAGE_X10 750
|
||||
#define TIP_THERMAL_MASS 65 // X10 watts to raise 1 deg C in 1 second
|
||||
#define TIP_RESISTANCE 75 // x10 ohms, 7.5 typical for ts100 tips
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80
|
||||
#define HARDWARE_MAX_WATTAGE_X10 180
|
||||
#define TIP_THERMAL_MASS 40
|
||||
#define TIP_RESISTANCE 45 // x10 ohms, 4.5 typical for ts80 tips
|
||||
#endif
|
||||
|
||||
#ifdef MODEL_TS80P
|
||||
#define HARDWARE_MAX_WATTAGE_X10 300
|
||||
#define TIP_THERMAL_MASS 40
|
||||
#define TIP_RESISTANCE 45 // x10 ohms, 4.5 typical for ts80 tips
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define FLASH_LOGOADDR (0x08000000 + (62 * 1024))
|
||||
#define FLASH_LOGOADDR (0x08000000 + (62 * 1024))
|
||||
|
||||
Reference in New Issue
Block a user