Initial Setup
This commit is contained in:
efflicto
@@ -1258,7 +1258,7 @@
|
||||
*
|
||||
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
|
||||
*/
|
||||
//#define S_CURVE_ACCELERATION
|
||||
#define S_CURVE_ACCELERATION
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
@@ -1640,7 +1640,7 @@
|
||||
// @section motion
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
//#define INVERT_I_DIR false
|
||||
@@ -1653,7 +1653,7 @@
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E0_DIR true
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
@@ -1694,8 +1694,8 @@
|
||||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 220
|
||||
#define Y_BED_SIZE 220
|
||||
|
||||
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
@@ -1703,7 +1703,7 @@
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 250
|
||||
//#define I_MIN_POS 0
|
||||
//#define I_MAX_POS 50
|
||||
//#define J_MIN_POS 0
|
||||
@@ -1731,7 +1731,7 @@
|
||||
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
|
||||
#define MIN_SOFTWARE_ENDSTOP_X
|
||||
#define MIN_SOFTWARE_ENDSTOP_Y
|
||||
#define MIN_SOFTWARE_ENDSTOP_Z
|
||||
//#define MIN_SOFTWARE_ENDSTOP_Z
|
||||
#define MIN_SOFTWARE_ENDSTOP_I
|
||||
#define MIN_SOFTWARE_ENDSTOP_J
|
||||
#define MIN_SOFTWARE_ENDSTOP_K
|
||||
@@ -1875,14 +1875,14 @@
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable one of
|
||||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
@@ -1985,8 +1985,8 @@
|
||||
|
||||
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
|
||||
#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 6 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
|
||||
@@ -2006,7 +2006,7 @@
|
||||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 6 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
@@ -2090,7 +2090,7 @@
|
||||
* - Allows Z homing only when XY positions are known and trusted.
|
||||
* - If stepper drivers sleep, XY homing may be required again before Z homing.
|
||||
*/
|
||||
//#define Z_SAFE_HOMING
|
||||
#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
|
||||
@@ -2176,7 +2176,7 @@
|
||||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
@@ -2215,16 +2215,16 @@
|
||||
// Preheat Constants - Up to 10 are supported without changes
|
||||
//
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_HOTEND 185
|
||||
#define PREHEAT_1_TEMP_BED 45
|
||||
#define PREHEAT_1_TEMP_CHAMBER 35
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_TEMP_BED 70
|
||||
#define PREHEAT_2_TEMP_CHAMBER 35
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
|
||||
|
||||
// @section motion
|
||||
|
||||
@@ -2239,7 +2239,7 @@
|
||||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
@@ -2422,7 +2422,7 @@
|
||||
*
|
||||
* :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek (Greece)', 'el_CY':'Greek (Cyprus)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' }
|
||||
*/
|
||||
#define LCD_LANGUAGE en
|
||||
#define LCD_LANGUAGE de
|
||||
|
||||
/**
|
||||
* LCD Character Set
|
||||
@@ -2461,7 +2461,7 @@
|
||||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
@@ -2839,7 +2839,7 @@
|
||||
// This is RAMPS-compatible using a single 10-pin connector.
|
||||
// (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
|
||||
//
|
||||
//#define CR10_STOCKDISPLAY
|
||||
#define CR10_STOCKDISPLAY
|
||||
|
||||
//
|
||||
// Ender-2 OEM display, a variant of the MKS_MINI_12864
|
||||
|
||||
Reference in New Issue
Block a user