286afad919
* Mock S60 * cleanup * Start refactor of OLED init * Setup timers roughly * Set Vector table offset correctly Update system_stm32f1xx.c * Update OLED.cpp * Update stm32f1xx_hal_msp.c * Update configuration.h * I2C init before GPIO From Errata Update stm32f1xx_hal_msp.c Update Software_I2C.h Allow no hardware I2C * I2C BB run bus unlock at init * cleanups * Software I2C for now * Mildly more graceful Interpolate * Handle is powered by DC Update Power.cpp Update drawPowerSourceIcon.cpp Update configuration.h Update Setup.cpp * Cleanup HomeScreen * Segment remap oled at init * Cleanup * Update MOVThread.cpp * Fix PWM Init * Fix adc2 trigger * Update configs * Fixup warning * Saner default config * Update ThermoModel.cpp * Util for current@voltage * Hub238 warning * Add hub238 handling in power mode * Update USBPDDebug_FUSB.cpp * HUSB238 debug * Hook PSU Limit * Use wrapping section of GRAM for scroll Update OLED.hpp * Update NTC table * Fix HUB voltage picker * Cleanup * Larger tip filter * Calibrate in a bunch closer Update ThermoModel.cpp * Update configuration.h * Update HUB238.cpp * Update configuration.h * Movement Pin * Update BSP.cpp * tim2 irq * Rough timer conversion (adc broken) but movement working * Fix tim2 start * Faster base PWM * Ensure utils grabs config * Add wattage limiter tolerance for device * Speed up PWM and enable PWM current limiting * tune for 12v * Prevent start until PD done * Update configuration.h * Add HUB238 check for have re-negotiated * Adjust timer to avoid noise when its possible
44 lines
1.3 KiB
C
44 lines
1.3 KiB
C
/*
|
|
* Pins.h
|
|
*
|
|
* Created on: 29 May 2020
|
|
* Author: Ralim
|
|
*/
|
|
|
|
#ifndef BSP_MINIWARE_PINS_H_
|
|
#define BSP_MINIWARE_PINS_H_
|
|
#include "configuration.h"
|
|
|
|
#ifdef MODEL_S60
|
|
|
|
#define KEY_B_Pin GPIO_PIN_1
|
|
#define KEY_B_GPIO_Port GPIOB
|
|
#define TMP36_INPUT_Pin GPIO_PIN_5
|
|
#define TMP36_INPUT_GPIO_Port GPIOA
|
|
#define TMP36_ADC1_CHANNEL ADC_CHANNEL_5
|
|
#define TMP36_ADC2_CHANNEL ADC_CHANNEL_5
|
|
#define TIP_TEMP_Pin GPIO_PIN_0
|
|
#define TIP_TEMP_GPIO_Port GPIOA
|
|
#define TIP_TEMP_ADC1_CHANNEL ADC_CHANNEL_0
|
|
#define TIP_TEMP_ADC2_CHANNEL ADC_CHANNEL_0
|
|
#define VIN_Pin GPIO_PIN_4
|
|
#define VIN_GPIO_Port GPIOA
|
|
#define VIN_ADC1_CHANNEL ADC_CHANNEL_4
|
|
#define VIN_ADC2_CHANNEL ADC_CHANNEL_4
|
|
#define KEY_A_Pin GPIO_PIN_0
|
|
#define KEY_A_GPIO_Port GPIOB
|
|
#define PWM_Out_Pin GPIO_PIN_8
|
|
#define PWM_Out_GPIO_Port GPIOB
|
|
#define PWM_Out_CHANNEL TIM_CHANNEL_3 // Timer 4; channel 3
|
|
#define SCL2_Pin GPIO_PIN_6
|
|
#define SCL2_GPIO_Port GPIOB
|
|
#define SDA2_Pin GPIO_PIN_7
|
|
#define SDA2_GPIO_Port GPIOB
|
|
// Pin gets pulled high on movement
|
|
#define MOVEMENT_Pin GPIO_PIN_3
|
|
#define MOVEMENT_GPIO_Port GPIOA
|
|
|
|
#endif
|
|
|
|
#endif /* BSP_MINIWARE_PINS_H_ */
|