e3bad2adae
* MHP30 move to I2C Bit Banging * Fixup Accelerometer drivers so all can use I2CBB * No STM32 I2C driver anymore * TS100 on I2CBB * Miniware on BB * Fixup S60 build * format format
172 lines
5.9 KiB
C
172 lines
5.9 KiB
C
#ifndef CONFIGURATION_H_
|
|
#define CONFIGURATION_H_
|
|
#include "Settings.h"
|
|
#include <stdint.h>
|
|
/**
|
|
* Configuration.h
|
|
* Define here your default pre settings for S60
|
|
*
|
|
*/
|
|
|
|
//===========================================================================
|
|
//============================= Default Settings ============================
|
|
//===========================================================================
|
|
/**
|
|
* Default soldering temp is 320.0 C
|
|
* Temperature the iron sleeps at - default 150.0 C
|
|
*/
|
|
|
|
#define SLEEP_TEMP 150 // Default sleep temperature
|
|
#define BOOST_TEMP 420 // Default boost temp.
|
|
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* OLED Brightness
|
|
*
|
|
*/
|
|
#define MIN_BRIGHTNESS 0 // Min OLED brightness selectable
|
|
#define MAX_BRIGHTNESS 100 // Max OLED brightness selectable
|
|
#define BRIGHTNESS_STEP 25 // OLED brightness increment
|
|
#define DEFAULT_BRIGHTNESS 25 // default OLED brightness
|
|
|
|
/**
|
|
* Blink the temperature on the cooling screen when its > 50C
|
|
*/
|
|
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* How many seconds/minutes we wait until going to sleep/shutdown.
|
|
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
|
|
*/
|
|
#define SLEEP_TIME 5 // x10 Seconds
|
|
#define SHUTDOWN_TIME 10 // Minutes
|
|
|
|
/**
|
|
* Auto start off for safety.
|
|
* Pissible values are:
|
|
* 0 - none
|
|
* 1 - Soldering Temperature
|
|
* 2 - Sleep Temperature
|
|
* 3 - Sleep Off Temperature
|
|
*/
|
|
#define AUTO_START_MODE 0 // Default to none
|
|
|
|
/**
|
|
* Locking Mode
|
|
* When in soldering mode a long press on both keys toggle the lock of the buttons
|
|
* Possible values are:
|
|
* 0 - Desactivated
|
|
* 1 - Lock except boost
|
|
* 2 - Full lock
|
|
*/
|
|
#define LOCKING_MODE 0 // Default to desactivated for safety
|
|
|
|
/**
|
|
* OLED Orientation
|
|
*
|
|
*/
|
|
#define ORIENTATION_MODE 0 // 0: Right 1:Left 2:Automatic - Default Automatic
|
|
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
|
|
|
|
/**
|
|
* Temp change settings
|
|
*/
|
|
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
|
|
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
|
|
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
|
|
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
|
|
|
|
/* Power pulse for keeping power banks awake*/
|
|
#define POWER_PULSE_INCREMENT 1
|
|
#define POWER_PULSE_MAX 100 // x10 max watts
|
|
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
|
|
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
|
|
|
|
#define POWER_PULSE_DEFAULT 0
|
|
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
|
|
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
|
|
|
|
/**
|
|
* OLED Orientation Sensitivity on Automatic mode!
|
|
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
|
|
*/
|
|
#define SENSITIVITY 7 // Default 7
|
|
|
|
/**
|
|
* Detailed soldering screen
|
|
* Detailed idle screen (off for first time users)
|
|
*/
|
|
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
|
|
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
|
|
|
|
#define THERMAL_RUNAWAY_TIME_SEC 20
|
|
#define THERMAL_RUNAWAY_TEMP_C 10
|
|
|
|
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
|
|
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
|
|
#define TEMPERATURE_INF 0 // default to 0
|
|
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
|
|
#define ANIMATION_LOOP 1 // 0: off 1: on
|
|
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
|
|
|
|
// Op-amp gain
|
|
// First stage has a gain of 10.31, followed by gain of 52; so total gain is 536
|
|
|
|
#define ADC_MAX_READING (4096 * 8) // Maximum reading of the adc
|
|
#define ADC_VDD_MV 3300 // ADC max reading millivolts
|
|
|
|
// Deriving the Voltage div:
|
|
// Vin_max = (3.3*(r1+r2))/(r2)
|
|
// vdiv = (32768*4)/(vin_max*10)
|
|
|
|
#if defined(MODEL_S60) == 0
|
|
#error "No model defined!"
|
|
#endif
|
|
|
|
#define NEEDS_VBUS_PROBE 0
|
|
|
|
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
|
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
|
#define PID_TIM_HZ (8) // Tick rate of the PID loop
|
|
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
|
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
|
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
|
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
|
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
|
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
|
|
|
#ifdef MODEL_S60
|
|
#define VOLTAGE_DIV 460 // Default divider scaler
|
|
#define CALIBRATION_OFFSET 200 // Default adc offset in uV
|
|
#define PID_POWER_LIMIT 70 // Sets the max pwm power limit
|
|
#define POWER_LIMIT 0 // 0 watts default limit
|
|
#define MAX_POWER_LIMIT 70
|
|
#define POWER_LIMIT_STEPS 5
|
|
#define OP_AMP_GAIN_STAGE 536
|
|
#define TEMP_uV_LOOKUP_S60
|
|
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate
|
|
|
|
#define HARDWARE_MAX_WATTAGE_X10 600
|
|
|
|
#define TIP_THERMAL_MASS 8 // X10 watts to raise 1 deg C in 1 second
|
|
#define TIP_THERMAL_INERTIA 128 // We use a large inertia value to smooth out the drive to the tip since its stupidly sensitive
|
|
|
|
#define TIP_RESISTANCE 20 //(actually 2.5 ish but we need to be more conservative on pwm'ing watt limit) x10 ohms
|
|
|
|
#define OLED_128x32
|
|
#define GPIO_VIBRATION
|
|
#define POW_PD_EXT 1
|
|
#define DEBUG_POWER_MENU_BUTTON_B 1
|
|
#define HAS_POWER_DEBUG_MENU
|
|
#define TEMP_NTC
|
|
#define I2C_SOFT_BUS_2 // For now we are doing software I2C to get around hardware chip issues
|
|
#define OLED_I2CBB2
|
|
|
|
#define MODEL_HAS_DCDC // We dont have DC/DC but have reallly fast PWM that gets us roughly the same place
|
|
#endif /* S60 */
|
|
|
|
#define FLASH_LOGOADDR (0x08000000 + (62 * 1024))
|
|
#define SETTINGS_START_PAGE (0x08000000 + (63 * 1024))
|
|
|
|
#endif /* CONFIGURATION_H_ */
|