124 lines
4.0 KiB
C++
124 lines
4.0 KiB
C++
/*
|
||
* TipThermoModel.cpp
|
||
*
|
||
* Created on: 7 Oct 2019
|
||
* Author: ralim
|
||
*/
|
||
|
||
#include "TipThermoModel.h"
|
||
#include "Settings.h"
|
||
#include "BSP.h"
|
||
#include "../../configuration.h"
|
||
|
||
/*
|
||
* The hardware is laid out as a non-inverting op-amp
|
||
* There is a pullup of 39k(TS100) from the +ve input to 3.9V (1M pulup on TS100)
|
||
*
|
||
* The simplest case to model this, is to ignore the pullup resistors influence, and assume that its influence is mostly constant
|
||
* -> Tip resistance *does* change with temp, but this should be much less than the rest of the system.
|
||
*
|
||
* When a thermocouple is equal temperature at both sides (hot and cold junction), then the output should be 0uV
|
||
* Therefore, by measuring the uV when both are equal, the measured reading is the offset value.
|
||
* This is a mix of the pull-up resistor, combined with tip manufacturing differences.
|
||
*
|
||
* All of the thermocouple readings are based on this expired patent
|
||
* - > https://patents.google.com/patent/US6087631A/en
|
||
*
|
||
* This was bought to my attention by <Kuba Sztandera>
|
||
*/
|
||
|
||
uint32_t TipThermoModel::convertTipRawADCTouV(uint16_t rawADC) {
|
||
// This takes the raw ADC samples, converts these to uV
|
||
// Then divides this down by the gain to convert to the uV on the input to the op-amp (A+B terminals)
|
||
// Then remove the calibration value that is stored as a tip offset
|
||
uint32_t vddRailmVX10 = 33000;//The vreg is +-2%, but we have no higher accuracy available
|
||
// 4096 * 8 readings for full scale
|
||
// Convert the input ADC reading back into mV times 10 format.
|
||
uint32_t rawInputmVX10 = (rawADC * vddRailmVX10) / (4096 * 8);
|
||
|
||
uint32_t valueuV = rawInputmVX10 * 100; // shift into uV
|
||
//Now to divide this down by the gain
|
||
valueuV = (valueuV) / OP_AMP_GAIN_STAGE;
|
||
//Remove uV tipOffset
|
||
if (valueuV >= systemSettings.CalibrationOffset)
|
||
valueuV -= systemSettings.CalibrationOffset;
|
||
else
|
||
valueuV = 0;
|
||
|
||
return valueuV;
|
||
}
|
||
|
||
uint32_t TipThermoModel::convertTipRawADCToDegC(uint16_t rawADC) {
|
||
return convertuVToDegC(convertTipRawADCTouV(rawADC));
|
||
}
|
||
#ifdef ENABLED_FAHRENHEIT_SUPPORT
|
||
uint32_t TipThermoModel::convertTipRawADCToDegF(uint16_t rawADC) {
|
||
return convertuVToDegF(convertTipRawADCTouV(rawADC));
|
||
}
|
||
#endif
|
||
|
||
//Table that is designed to be walked to find the best sample for the lookup
|
||
|
||
//Extrapolate between two points
|
||
// [x1, y1] = point 1
|
||
// [x2, y2] = point 2
|
||
// x = input value
|
||
// output is x's extrapolated y value
|
||
int32_t LinearInterpolate(int32_t x1, int32_t y1, int32_t x2, int32_t y2,
|
||
int32_t x) {
|
||
return y1 + (((((x - x1) * 1000) / (x2 - x1)) * (y2 - y1))) / 1000;
|
||
}
|
||
|
||
uint32_t TipThermoModel::convertuVToDegC(uint32_t tipuVDelta) {
|
||
//based on new measurements, tip is quite linear
|
||
//
|
||
tipuVDelta *= 10;
|
||
tipuVDelta /= systemSettings.TipGain;
|
||
|
||
#if defined( MODEL_TS80)+defined( MODEL_TS80P)>0
|
||
tipuVDelta /= OP_AMP_GAIN_STAGE_TS100 / OP_AMP_GAIN_STAGE_TS80;
|
||
#endif
|
||
|
||
return tipuVDelta;
|
||
}
|
||
|
||
#ifdef ENABLED_FAHRENHEIT_SUPPORT
|
||
uint32_t TipThermoModel::convertuVToDegF(uint32_t tipuVDelta) {
|
||
return convertCtoF(convertuVToDegC(tipuVDelta));
|
||
}
|
||
|
||
uint32_t TipThermoModel::convertCtoF(uint32_t degC) {
|
||
//(Y °C × 9/5) + 32 =Y°F
|
||
return 32 + ((degC * 9) / 5);
|
||
}
|
||
|
||
uint32_t TipThermoModel::convertFtoC(uint32_t degF) {
|
||
//(Y°F − 32) × 5/9 = Y°C
|
||
if (degF < 32)
|
||
return 0;
|
||
return ((degF - 32) * 5) / 9;
|
||
}
|
||
#endif
|
||
|
||
uint32_t TipThermoModel::getTipInC(bool sampleNow) {
|
||
uint32_t currentTipTempInC = TipThermoModel::convertTipRawADCToDegC(
|
||
getTipRawTemp(sampleNow));
|
||
currentTipTempInC += getHandleTemperature() / 10; //Add handle offset
|
||
return currentTipTempInC;
|
||
}
|
||
#ifdef ENABLED_FAHRENHEIT_SUPPORT
|
||
uint32_t TipThermoModel::getTipInF(bool sampleNow) {
|
||
uint32_t currentTipTempInF = TipThermoModel::convertTipRawADCToDegF(
|
||
getTipRawTemp(sampleNow));
|
||
currentTipTempInF += convertCtoF(getHandleTemperature() / 10); //Add handle offset
|
||
return currentTipTempInF;
|
||
}
|
||
#endif
|
||
|
||
uint32_t TipThermoModel::getTipMaxInC() {
|
||
uint32_t maximumTipTemp = TipThermoModel::convertTipRawADCToDegC(
|
||
0x7FFF - (80 * 5)); //back off approx 5 deg c from ADC max
|
||
maximumTipTemp += getHandleTemperature() / 10; //Add handle offset
|
||
return maximumTipTemp - 1;
|
||
}
|