157 lines
5.7 KiB
C
157 lines
5.7 KiB
C
#ifndef CONFIGURATION_H_
|
|
#define CONFIGURATION_H_
|
|
#include "Settings.h"
|
|
#include "configuration.h"
|
|
#include <stdint.h>
|
|
/**
|
|
* Configuration.h
|
|
* Define here your default pre settings for TS80 or TS100
|
|
*
|
|
*/
|
|
|
|
//===========================================================================
|
|
//============================= Default Settings ============================
|
|
//===========================================================================
|
|
/**
|
|
* Default soldering temp is 320.0 C
|
|
* Temperature the iron sleeps at - default 150.0 C
|
|
*/
|
|
|
|
#define SLEEP_TEMP 150 // Default sleep temperature
|
|
#define BOOST_TEMP 420 // Default boost temp.
|
|
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* Blink the temperature on the cooling screen when its > 50C
|
|
*/
|
|
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* How many seconds/minutes we wait until going to sleep/shutdown.
|
|
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
|
|
*/
|
|
#define SLEEP_TIME 5 // x10 Seconds
|
|
#define SHUTDOWN_TIME 10 // Minutes
|
|
|
|
/**
|
|
* Auto start off for safety.
|
|
* Pissible values are:
|
|
* 0 - none
|
|
* 1 - Soldering Temperature
|
|
* 2 - Sleep Temperature
|
|
* 3 - Sleep Off Temperature
|
|
*/
|
|
#define AUTO_START_MODE 0 // Default to none
|
|
|
|
/**
|
|
* Locking Mode
|
|
* When in soldering mode a long press on both keys toggle the lock of the buttons
|
|
* Possible values are:
|
|
* 0 - Desactivated
|
|
* 1 - Lock except boost
|
|
* 2 - Full lock
|
|
*/
|
|
#define LOCKING_MODE 0 // Default to desactivated for safety
|
|
|
|
/**
|
|
* OLED Orientation
|
|
*
|
|
*/
|
|
#define ORIENTATION_MODE 0 // 0: Right 1:Left 2:Automatic - Default right
|
|
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
|
|
|
|
/**
|
|
* Temp change settings
|
|
*/
|
|
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
|
|
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
|
|
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
|
|
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
|
|
|
|
/* Power pulse for keeping power banks awake*/
|
|
#define POWER_PULSE_INCREMENT 1
|
|
#define POWER_PULSE_MAX 100 // x10 max watts
|
|
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
|
|
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
|
|
|
|
#ifdef MODEL_TS100
|
|
#define POWER_PULSE_DEFAULT 0
|
|
#else
|
|
#define POWER_PULSE_DEFAULT 5
|
|
#endif
|
|
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
|
|
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
|
|
|
|
/**
|
|
* OLED Orientation Sensitivity on Automatic mode!
|
|
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
|
|
*/
|
|
#define SENSITIVITY 7 // Default 7
|
|
|
|
/**
|
|
* Detailed soldering screen
|
|
* Detailed idle screen (off for first time users)
|
|
*/
|
|
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
|
|
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
|
|
// Due to large thermal mass of the PCB being heated we need to pull this back a bit
|
|
#define THERMAL_RUNAWAY_TIME_SEC 30
|
|
#define THERMAL_RUNAWAY_TEMP_C 3
|
|
|
|
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
|
|
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
|
|
#define TEMPERATURE_INF 0 // default to 0
|
|
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
|
|
#define ANIMATION_LOOP 1 // 0: off 1: on
|
|
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
|
|
|
|
#define OP_AMP_Rf_MHP30 268500 // 268.5 Kilo-ohms -> Measured
|
|
#define OP_AMP_Rin_MHP30 1600 // 1.6 Kilo-ohms -> Measured
|
|
|
|
#define OP_AMP_GAIN_STAGE_MHP30 (1 + (OP_AMP_Rf_MHP30 / OP_AMP_Rin_MHP30))
|
|
// Deriving the Voltage div:
|
|
// Vin_max = (3.3*(r1+r2))/(r2)
|
|
// vdiv = (32768*4)/(vin_max*10)
|
|
|
|
#ifndef MODEL_MHP30
|
|
#error "No model defined!"
|
|
#endif
|
|
|
|
#ifdef MODEL_MHP30
|
|
#define SOLDERING_TEMP 200 // Default soldering temp is 200.0 °C
|
|
#define VOLTAGE_DIV 360 // Default for MHP30
|
|
#define PID_POWER_LIMIT 65 // Sets the max pwm power limit
|
|
#define CALIBRATION_OFFSET 0 // the adc offset in uV - MHP compensates automagically
|
|
#define POWER_LIMIT 65 // 65 watts default power limit
|
|
#define MAX_POWER_LIMIT 65 //
|
|
#define POWER_LIMIT_STEPS 1 //
|
|
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_MHP30 //
|
|
#define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate
|
|
#define MODEL_HAS_DCDC // Has inductor to current filter
|
|
#define PID_TIM_HZ (16) //
|
|
#define MAX_TEMP_C 300 // Max soldering temp selectable °C
|
|
#define MAX_TEMP_F 570 // Max soldering temp selectable °F
|
|
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
|
#define MIN_TEMP_F 60 // Min soldering temp selectable °F
|
|
#define MIN_BOOST_TEMP_C 150 // The min settable temp for boost mode °C
|
|
#define MIN_BOOST_TEMP_F 300 // The min settable temp for boost mode °F
|
|
#define NO_DISPLAY_ROTATE // Disable OLED rotation by accel
|
|
#define SLEW_LIMIT 50 // Limit to 3.0 Watts per 64ms pid loop update rate slew rate
|
|
#define ACCEL_MSA
|
|
#define POW_PD 1
|
|
#define TEMP_NTC
|
|
#define I2C_SOFT
|
|
#define BATTFILTERDEPTH 8
|
|
#define OLED_I2CBB
|
|
#define ACCEL_EXITS_ON_MOVEMENT
|
|
|
|
#define HARDWARE_MAX_WATTAGE_X10 650
|
|
#define TIP_THERMAL_MASS 65 // TODO, needs refinement
|
|
#define TIP_RESISTANCE 60 // x10 ohms, ~6 typical
|
|
#endif
|
|
|
|
#ifdef ACCEL_EXITS_ON_MOVEMENT
|
|
#define NO_SLEEP_MODE
|
|
#endif
|
|
#endif
|