286afad919
* Mock S60 * cleanup * Start refactor of OLED init * Setup timers roughly * Set Vector table offset correctly Update system_stm32f1xx.c * Update OLED.cpp * Update stm32f1xx_hal_msp.c * Update configuration.h * I2C init before GPIO From Errata Update stm32f1xx_hal_msp.c Update Software_I2C.h Allow no hardware I2C * I2C BB run bus unlock at init * cleanups * Software I2C for now * Mildly more graceful Interpolate * Handle is powered by DC Update Power.cpp Update drawPowerSourceIcon.cpp Update configuration.h Update Setup.cpp * Cleanup HomeScreen * Segment remap oled at init * Cleanup * Update MOVThread.cpp * Fix PWM Init * Fix adc2 trigger * Update configs * Fixup warning * Saner default config * Update ThermoModel.cpp * Util for current@voltage * Hub238 warning * Add hub238 handling in power mode * Update USBPDDebug_FUSB.cpp * HUSB238 debug * Hook PSU Limit * Use wrapping section of GRAM for scroll Update OLED.hpp * Update NTC table * Fix HUB voltage picker * Cleanup * Larger tip filter * Calibrate in a bunch closer Update ThermoModel.cpp * Update configuration.h * Update HUB238.cpp * Update configuration.h * Movement Pin * Update BSP.cpp * tim2 irq * Rough timer conversion (adc broken) but movement working * Fix tim2 start * Faster base PWM * Ensure utils grabs config * Add wattage limiter tolerance for device * Speed up PWM and enable PWM current limiting * tune for 12v * Prevent start until PD done * Update configuration.h * Add HUB238 check for have re-negotiated * Adjust timer to avoid noise when its possible
43 lines
1.7 KiB
C++
43 lines
1.7 KiB
C++
#include "OperatingModeUtilities.h"
|
|
|
|
void gui_drawBatteryIcon(void) {
|
|
#if defined(POW_PD) || defined(POW_QC) || defined(POW_PD_EXT)
|
|
if (!getIsPoweredByDCIN()) {
|
|
// On non-DC inputs we replace this symbol with the voltage we are operating on
|
|
// If <9V then show single digit, if not show dual small ones vertically stacked
|
|
uint16_t V = getInputVoltageX10(getSettingValue(SettingsOptions::VoltageDiv), 0);
|
|
if (V % 10 >= 5)
|
|
V = (V / 10) + 1; // round up
|
|
else
|
|
V = V / 10;
|
|
if (V > 9) {
|
|
int16_t xPos = OLED::getCursorX();
|
|
OLED::printNumber(V / 10, 1, FontStyle::SMALL);
|
|
OLED::setCursor(xPos, 8);
|
|
OLED::printNumber(V % 10, 1, FontStyle::SMALL);
|
|
OLED::setCursor(xPos + 12, 0); // need to reset this as if we drew a wide char
|
|
} else {
|
|
OLED::printNumber(V, 1, FontStyle::LARGE);
|
|
}
|
|
return;
|
|
}
|
|
#endif
|
|
#ifdef POW_DC
|
|
if (getSettingValue(SettingsOptions::MinDCVoltageCells)) {
|
|
// User is on a lithium battery
|
|
// we need to calculate which of the 10 levels they are on
|
|
uint8_t cellCount = getSettingValue(SettingsOptions::MinDCVoltageCells) + 2;
|
|
uint32_t cellV = getInputVoltageX10(getSettingValue(SettingsOptions::VoltageDiv), 0) / cellCount;
|
|
// Should give us approx cell voltage X10
|
|
// Range is 42 -> Minimum voltage setting (systemSettings.minVoltageCells) = 9 steps therefore we will use battery 0-9
|
|
if (cellV < getSettingValue(SettingsOptions::MinVoltageCells))
|
|
cellV = getSettingValue(SettingsOptions::MinVoltageCells);
|
|
cellV -= getSettingValue(SettingsOptions::MinVoltageCells); // Should leave us a number of 0-9
|
|
if (cellV > 9)
|
|
cellV = 9;
|
|
OLED::drawBattery(cellV + 1);
|
|
} else {
|
|
OLED::drawSymbol(15); // Draw the DC Logo
|
|
}
|
|
#endif
|
|
} |