286afad919
* Mock S60 * cleanup * Start refactor of OLED init * Setup timers roughly * Set Vector table offset correctly Update system_stm32f1xx.c * Update OLED.cpp * Update stm32f1xx_hal_msp.c * Update configuration.h * I2C init before GPIO From Errata Update stm32f1xx_hal_msp.c Update Software_I2C.h Allow no hardware I2C * I2C BB run bus unlock at init * cleanups * Software I2C for now * Mildly more graceful Interpolate * Handle is powered by DC Update Power.cpp Update drawPowerSourceIcon.cpp Update configuration.h Update Setup.cpp * Cleanup HomeScreen * Segment remap oled at init * Cleanup * Update MOVThread.cpp * Fix PWM Init * Fix adc2 trigger * Update configs * Fixup warning * Saner default config * Update ThermoModel.cpp * Util for current@voltage * Hub238 warning * Add hub238 handling in power mode * Update USBPDDebug_FUSB.cpp * HUSB238 debug * Hook PSU Limit * Use wrapping section of GRAM for scroll Update OLED.hpp * Update NTC table * Fix HUB voltage picker * Cleanup * Larger tip filter * Calibrate in a bunch closer Update ThermoModel.cpp * Update configuration.h * Update HUB238.cpp * Update configuration.h * Movement Pin * Update BSP.cpp * tim2 irq * Rough timer conversion (adc broken) but movement working * Fix tim2 start * Faster base PWM * Ensure utils grabs config * Add wattage limiter tolerance for device * Speed up PWM and enable PWM current limiting * tune for 12v * Prevent start until PD done * Update configuration.h * Add HUB238 check for have re-negotiated * Adjust timer to avoid noise when its possible
56 lines
1.9 KiB
C++
56 lines
1.9 KiB
C++
#include "HUB238.hpp"
|
|
#include "OperatingModes.h"
|
|
#if POW_PD_EXT == 1
|
|
#ifdef HAS_POWER_DEBUG_MENU
|
|
void showPDDebug(void) {
|
|
// Print out the USB-PD state
|
|
// Basically this is like the Debug menu, but instead we want to print out the PD status
|
|
uint8_t screen = 0;
|
|
ButtonState b;
|
|
for (;;) {
|
|
OLED::clearScreen(); // Ensure the buffer starts clean
|
|
OLED::setCursor(0, 0); // Position the cursor at the 0,0 (top left)
|
|
OLED::print(SmallSymbolPDDebug, FontStyle::SMALL); // Print Title
|
|
OLED::setCursor(0, 8); // second line
|
|
if (screen > 6) {
|
|
screen = 0;
|
|
}
|
|
if (screen == 0) {
|
|
// Print the PD Debug state
|
|
OLED::print(SmallSymbolState, FontStyle::SMALL);
|
|
OLED::print(SmallSymbolSpace, FontStyle::SMALL);
|
|
uint16_t temp = hub238_debug_state();
|
|
OLED::drawHex(temp, FontStyle::SMALL, 4);
|
|
OLED::print(SmallSymbolSpace, FontStyle::SMALL);
|
|
// Print current selected specs
|
|
temp = hub238_source_voltage();
|
|
OLED::printNumber(temp, 2, FontStyle::SMALL, true);
|
|
OLED::print(SmallSymbolSpace, FontStyle::SMALL);
|
|
|
|
} else {
|
|
|
|
// Print out the Proposed power options one by one
|
|
const uint8_t voltages[] = {5, 9, 12, 15, 18, 20};
|
|
uint16_t voltage = voltages[screen - 1];
|
|
uint16_t currentx100 = hub238_getVoltagePDOCurrent(voltage);
|
|
OLED::printNumber(voltage, 2, FontStyle::SMALL, true);
|
|
OLED::print(SmallSymbolSpace, FontStyle::SMALL);
|
|
|
|
OLED::printNumber(currentx100 / 100, 1, FontStyle::SMALL, true);
|
|
OLED::print(SmallSymbolDot, FontStyle::SMALL);
|
|
OLED::printNumber(currentx100 % 100, 2, FontStyle::SMALL, true);
|
|
}
|
|
|
|
OLED::refresh();
|
|
b = getButtonState();
|
|
if (b == BUTTON_B_SHORT)
|
|
return;
|
|
else if (b == BUTTON_F_SHORT) {
|
|
screen++;
|
|
}
|
|
GUIDelay();
|
|
}
|
|
}
|
|
#endif
|
|
#endif
|