#ifndef CONFIGURATION_H_ #define CONFIGURATION_H_ #include "Settings.h" #include "configuration.h" #include /** * Configuration.h * Define here your default pre settings for TS80 or TS100 * */ //=========================================================================== //============================= Default Settings ============================ //=========================================================================== /** * Default soldering temp is 320.0 C * Temperature the iron sleeps at - default 150.0 C */ #define SLEEP_TEMP 150 // Default sleep temperature #define BOOST_TEMP 420 // Default boost temp. #define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable /** * Blink the temperature on the cooling screen when its > 50C */ #define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable /** * How many seconds/minutes we wait until going to sleep/shutdown. * Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds! */ #define SLEEP_TIME 5 // x10 Seconds #define SHUTDOWN_TIME 10 // Minutes /** * Auto start off for safety. * Pissible values are: * 0 - none * 1 - Soldering Temperature * 2 - Sleep Temperature * 3 - Sleep Off Temperature */ #define AUTO_START_MODE 0 // Default to none /** * Locking Mode * When in soldering mode a long press on both keys toggle the lock of the buttons * Possible values are: * 0 - Desactivated * 1 - Lock except boost * 2 - Full lock */ #define LOCKING_MODE 0 // Default to desactivated for safety /** * OLED Orientation * */ #define ORIENTATION_MODE 0 // 0: Right 1:Left 2:Automatic - Default right #define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change /** * Temp change settings */ #define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1 #define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10 #define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value #define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value /* Power pulse for keeping power banks awake*/ #define POWER_PULSE_INCREMENT 1 #define POWER_PULSE_MAX 100 // x10 max watts #define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds #define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds #ifdef MODEL_TS100 #define POWER_PULSE_DEFAULT 0 #else #define POWER_PULSE_DEFAULT 5 #endif #define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s #define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms /** * OLED Orientation Sensitivity on Automatic mode! * Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive> */ #define SENSITIVITY 7 // Default 7 /** * Detailed soldering screen * Detailed idle screen (off for first time users) */ #define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0 #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 #define THERMAL_RUNAWAY_TIME_SEC 20 #define THERMAL_RUNAWAY_TEMP_C 20 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) #define TEMPERATURE_INF 0 // default to 0 #define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow #define ANIMATION_LOOP 1 // 0: off 1: on #define ANIMATION_SPEED settingOffSpeed_t::MEDIUM #define OP_AMP_Rf_MHP30 268500 // 268.5 Kilo-ohms -> Measured #define OP_AMP_Rin_MHP30 1600 // 1.6 Kilo-ohms -> Measured #define OP_AMP_GAIN_STAGE_MHP30 (1 + (OP_AMP_Rf_MHP30 / OP_AMP_Rin_MHP30)) // Deriving the Voltage div: // Vin_max = (3.3*(r1+r2))/(r2) // vdiv = (32768*4)/(vin_max*10) #ifndef MODEL_MHP30 #error "No model defined!" #endif #ifdef MODEL_MHP30 #define SOLDERING_TEMP 200 // Default soldering temp is 200.0 °C #define VOLTAGE_DIV 360 // Default for MHP30 #define PID_POWER_LIMIT 65 // Sets the max pwm power limit #define CALIBRATION_OFFSET 0 // the adc offset in uV - MHP compensates automagically #define POWER_LIMIT 65 // 65 watts default power limit #define MAX_POWER_LIMIT 65 // #define POWER_LIMIT_STEPS 1 // #define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_MHP30 // #define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate #define MODEL_HAS_DCDC // Has inductor to current filter #define PID_TIM_HZ (16) // #define MAX_TEMP_C 300 // Max soldering temp selectable °C #define MAX_TEMP_F 570 // Max soldering temp selectable °F #define MIN_TEMP_C 10 // Min soldering temp selectable °C #define MIN_TEMP_F 60 // Min soldering temp selectable °F #define MIN_BOOST_TEMP_C 150 // The min settable temp for boost mode °C #define MIN_BOOST_TEMP_F 300 // The min settable temp for boost mode °F #define NO_DISPLAY_ROTATE // Disable OLED rotation by accel #define SLEW_LIMIT 50 // Limit to 3.0 Watts per 64ms pid loop update rate slew rate #define ACCEL_MSA #define POW_PD 1 #define TEMP_NTC #define I2C_SOFT #define BATTFILTERDEPTH 8 #define OLED_I2CBB #define ACCEL_EXITS_ON_MOVEMENT #define HARDWARE_MAX_WATTAGE_X10 650 #define TIP_THERMAL_MASS 65 // TODO, needs refinement #define TIP_RESISTANCE 60 // x10 ohms, ~6 typical #endif #ifdef ACCEL_EXITS_ON_MOVEMENT #define NO_SLEEP_MODE #endif #endif