Patch to fix left handed screen

README.md

@@ -31,8 +31,15 @@ This is completely safe, if it goes wrong just put the .hex file from the offici
 6. If it ends with .RDY your done! Otherwise something went wrong.
 7. If it went wrong try on a windows computer, some Mac / Linux machines do not play well with their boot loader.
 
+There is also a complete device flash backup included in this repository. (Note this includes the bootloader, so will need a SWD programmer to load onto the unit).
 
 # New Menu System
 This new firmware uses a new menu system to allow access to the settings on the device.
 This menu can be accessed as shown in following flow chart, in the settings numbers roll over from top to bottom.
-![TS100: Software Menu](http://ralimtek.com/images/TS100.png "Fairly easy to learn")
+![TS100: Software Menu](TS100.png "Fairly easy to learn")
+
+
+# Version Changes:
+V1.02
+	- Adds hold both buttons on IDLE to access the therometer mode.
+	- Changes the exit soldering mode to be holding both buttons (Like original firmware).

workspace/ts100/inc/Oled.h

@@ -18,7 +18,7 @@ u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high, u8* ptr);
 void Set_ShowPos(u8 x, u8 y);
 void Oled_DisplayFlip();
 void GPIO_Init_OLED(void);
-void Init_Oled(void);
+void Init_Oled(uint8_t leftHanded);
 u8* Data_Command(u8 len, u8* ptr);
 void Clear_Screen(void);//Clear the screen
 /*Functions for writing to the screen*/

workspace/ts100/src/Main.c

@@ -30,13 +30,13 @@ void setup() {
 	I2C_Configuration();				//Start the I2C hardware
 	GPIO_Init_OLED();					//Init the GPIO ports for the OLED
 	StartUp_Accelerometer(); 			//start the accelerometer
-	Init_Oled(); 						//init the OLED display
+
 	setupPID(); 						//init the PID values
 	readIronTemp(239, 0); 				//load the default calibration value
 	restoreSettings();					//Load settings
-	if (systemSettings.flipDisplay)
+	Init_Oled(systemSettings.flipDisplay);//init the OLED display
-		Oled_DisplayFlip();
+
-	OLED_DrawString("VER 1.02",8);
+	OLED_DrawString("VER 1.03",8);
 	delayMs(800);
 	Start_Watchdog(1000); 		//start the system watchdog as 1 seconds timeout
 }

workspace/ts100/src/Oled.c

@@ -19,9 +19,9 @@ int8_t displayOffset = 32;
 /*All commands are prefixed with 0x80*/
 u8 OLED_Setup_Array[46] = { 0x80, 0xAE,/*Display off*/
 0x80, 0xD5,/*Set display clock divide ratio / osc freq*/
-0x80, 0b01010001,/**/
+0x80, 0x52,/**/
 0x80, 0xA8,/*Set Multiplex Ratio*/
-0x80, 16,  /*16 == max brightness,39==dimmest*/
+0x80, 0x0F, /*16 == max brightness,39==dimmest*/
 0x80, 0xC0,/*Set COM Scan direction*/
 0x80, 0xD3,/*Set Display offset*/
 0x80, 0x00,/*0 Offset*/
@@ -69,7 +69,7 @@ void Oled_DisplayFlip() {
 	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
 	data[1] = 0xA1;
 	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
-	displayOffset=0;
+	displayOffset = 0;
 
 }
 /*
@@ -79,10 +79,10 @@ void Oled_DisplayFlip() {
  */
 u8* Data_Command(u8 length, u8* data) {
 	int i;
-	u8 tx_data[128];
+	u8 tx_data[129];
 	//here are are inserting the data write command at the beginning
 	tx_data[0] = 0x40;
-	length += 1;
+	length++;
 	for (i = 1; i < length; i++) //Loop through the array of data
 		tx_data[i] = *data++;
 	I2C_PageWrite(tx_data, length, DEVICEADDR_OLED); //write out the buffer
@@ -144,14 +144,19 @@ void GPIO_Init_OLED(void) {
  Function: Init_Oled
  Description: Initalizes the Oled screen
  *******************************************************************************/
-void Init_Oled(void) {
+void Init_Oled(uint8_t leftHanded) {
 	u8 param_len;
 
 	OLED_RST();
-	delayMs(2);
+	delayMs(5);
 	OLED_ACT(); //Toggling reset to reset the oled
-	delayMs(2);
+	delayMs(5);
 	param_len = 46;
+	if (leftHanded) {
+		OLED_Setup_Array[11] = 0xC8;
+		OLED_Setup_Array[19] = 0xA1;
+		displayOffset = 0;
+	}
 	I2C_PageWrite((u8 *) OLED_Setup_Array, param_len, DEVICEADDR_OLED);
 }
 
@@ -196,8 +201,7 @@ void OLED_DrawChar(char c, uint8_t x) {
 		ptr += (37) * (FONT_WIDTH * 2);
 	} else if (c == '>') {
 		ptr += (38) * (FONT_WIDTH * 2);
-	}else if (c=='.')
+	} else if (c == '.') {
-	{
 		ptr += (39) * (FONT_WIDTH * 2);
 	}