Ben V. Brown
c308fe8cc2
Pinecil v2 tune via PID ( #1827 )
...
* Start PWM after adc irq fully done
* Filter len 4
* Use comparitor 2 on timer for wrap around
* Update IRQ.cpp
* Tip measurements are uint16_t
Update BSP.cpp
Update BSP.cpp
* WiP PID
move pid tuning to config
Update PIDThread.cpp
* Handle PWM Timer gitchy comparitor
* Tuning
* Dampen with Kd
* Cleaning up
* Use TemperatureType_t for getTipTemp()
* Add small rolling average to user GUI temp to reduce flicker
* Trigger PID when adc is skipped (will use old values)
2023-10-21 08:21:08 +11:00
Ben V. Brown
c120af398a
Merge branch 'dev' into Short-Detection
2023-08-02 15:52:49 +10:00
Ben V. Brown
80c4b58976
Abstract out showing bootlogo
...
To improve support on PinecilV2
2023-08-01 21:18:27 +10:00
Ben V. Brown
6d18e860f8
Merge branch 'dev' into Short-Detection
2023-07-28 20:04:16 +10:00
Ben V. Brown
344068d480
Add isTipShorted() to warnings
2023-07-28 19:59:54 +10:00
Ben V. Brown
9a3fef92c3
Allow S60 fallback to head if PD times out after 3 seconds
2023-07-28 18:40:16 +10:00
Ben V. Brown
e7bcf920ba
Refactor PinecilV2 Tuning
...
Closes #1688
2023-06-04 12:13:26 +10:00
Ben V. Brown
286afad919
S60 Support ( #1692 )
...
* Mock S60
* cleanup
* Start refactor of OLED init
* Setup timers roughly
* Set Vector table offset correctly
Update system_stm32f1xx.c
* Update OLED.cpp
* Update stm32f1xx_hal_msp.c
* Update configuration.h
* I2C init before GPIO
From Errata
Update stm32f1xx_hal_msp.c
Update Software_I2C.h
Allow no hardware I2C
* I2C BB run bus unlock at init
* cleanups
* Software I2C for now
* Mildly more graceful Interpolate
* Handle is powered by DC
Update Power.cpp
Update drawPowerSourceIcon.cpp
Update configuration.h
Update Setup.cpp
* Cleanup HomeScreen
* Segment remap oled at init
* Cleanup
* Update MOVThread.cpp
* Fix PWM Init
* Fix adc2 trigger
* Update configs
* Fixup warning
* Saner default config
* Update ThermoModel.cpp
* Util for current@voltage
* Hub238 warning
* Add hub238 handling in power mode
* Update USBPDDebug_FUSB.cpp
* HUSB238 debug
* Hook PSU Limit
* Use wrapping section of GRAM for scroll
Update OLED.hpp
* Update NTC table
* Fix HUB voltage picker
* Cleanup
* Larger tip filter
* Calibrate in a bunch closer
Update ThermoModel.cpp
* Update configuration.h
* Update HUB238.cpp
* Update configuration.h
* Movement Pin
* Update BSP.cpp
* tim2 irq
* Rough timer conversion (adc broken) but movement working
* Fix tim2 start
* Faster base PWM
* Ensure utils grabs config
* Add wattage limiter tolerance for device
* Speed up PWM and enable PWM current limiting
* tune for 12v
* Prevent start until PD done
* Update configuration.h
* Add HUB238 check for have re-negotiated
* Adjust timer to avoid noise when its possible
2023-06-03 20:05:31 +10:00
