diff --git a/Translations/translation_EN.json b/Translations/translation_EN.json
index a17d886c..cd662efe 100644
--- a/Translations/translation_EN.json
+++ b/Translations/translation_EN.json
@@ -97,9 +97,9 @@
 		"AdvancedMenu": {
 			"text2": [
 				"Advanced",
-				"options"
+				"settings"
 			],
-			"desc": "Advanced options"
+			"desc": "Advanced settings"
 		}
 	},
 	"menuOptions": {
@@ -108,7 +108,7 @@
 				"Power",
 				"source"
 			],
-			"desc": "Power source. Sets cutoff voltage. <DC 10V> <S 3.3V per cell, disable power limit>"
+			"desc": "Power source. Sets cutoff voltage. (DC 10V) (S 3.3V per cell, disable power limit)"
 		},
 		"SleepTemperature": {
 			"text2": [
@@ -122,14 +122,14 @@
 				"Sleep",
 				"timeout"
 			],
-			"desc": "Interval before \"sleep mode\" kicks in <S=seconds | M=minutes>"
+			"desc": "Interval before \"sleep mode\" kicks in (S=seconds | M=minutes)"
 		},
 		"ShutdownTimeout": {
 			"text2": [
 				"Shutdown",
 				"timeout"
 			],
-			"desc": "Interval before the iron shuts down <M=minutes>"
+			"desc": "Interval before the iron shuts down (M=minutes)"
 		},
 		"MotionSensitivity": {
 			"text2": [
@@ -168,17 +168,17 @@
 		},
 		"AutoStart": {
 			"text2": [
-				"Auto",
-				"start"
+				"Heat",
+				"on power up"
 			],
-			"desc": "Starts the iron into soldering mode on power up <O=off | S=soldering | Z=sleep | R=sleep at room temperature>"
+			"desc": "O=off | S=soldering temp | Z=standby at sleep temp until moved | R=standby without heating until moved"
 		},
 		"CooldownBlink": {
 			"text2": [
 				"Cooldown",
 				"blink"
 			],
-			"desc": "Flash the temperature after heating was halted, while the tip is still hot"
+			"desc": "Flash the temperature reading after heating was halted while the tip is still hot"
 		},
 		"TemperatureCalibration": {
 			"text2": [
@@ -199,7 +199,7 @@
 				"Calibrate",
 				"input voltage?"
 			],
-			"desc": "Start VIN calibration <long press to exit>"
+			"desc": "Start VIN calibration (long press to exit)"
 		},
 		"AdvancedSoldering": {
 			"text2": [
@@ -213,21 +213,21 @@
 				"Scrolling",
 				"speed"
 			],
-			"desc": "Speed info text scrolls past at <S=slow | F=fast>"
+			"desc": "Speed info text scrolls past at (S=slow | F=fast)"
 		},
 		"QCMaxVoltage": {
 			"text2": [
 				"QC",
 				"voltage"
 			],
-			"desc": "Desired max QC voltage the iron negotiates for"
+			"desc": "Max QC voltage the iron should negotiate for"
 		},
 		"PowerLimit": {
 			"text2": [
 				"Power",
 				"limit"
 			],
-			"desc": "Maximum power the iron can use <W=watt>"
+			"desc": "Maximum power the iron can use (W=watt)"
 		},
 		"ReverseButtonTempChange": {
 			"text2": [
@@ -255,28 +255,28 @@
 				"Power",
 				"pulse"
 			],
-			"desc": "Intensity of power of keep-awake-pulse <watt>"
+			"desc": "Intensity of power of keep-awake-pulse (watt)"
 		},
 		"HallEffSensitivity": {
 			"text2": [
 				"Hall sensor",
 				"sensitivity"
 			],
-			"desc": "Sensitivity of the Hall effect sensor to detect sleep <O=off | L=low | M=medium | H=high>"
+			"desc": "Sensitivity of the Hall effect sensor to detect sleep (O=off | L=low | M=medium | H=high)"
 		},
 		"LockingMode": {
 			"text2": [
 				"Allow locking",
 				"buttons"
 			],
-			"desc": "When soldering, long press both buttons, to lock them <D=disable | B=\"boost mode\" only | F=full locking>"
+			"desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)"
 		},
 		"MinVolCell": {
 			"text2": [
 				"Minimum",
 				"voltage"
 			],
-			"desc": "Minimum allowed voltage per cell <Volts> <3S: 3.0V - 3.7V, 4/5/6S: 2.4V - 3.7V>"
+			"desc": "Minimum allowed voltage per cell (3S: 3 - 3.7V | 4-6S: 2.4 - 3.7V)"
 		},
 		"AnimLoop": {
 			"text2": [
@@ -290,7 +290,7 @@
 				"Anim.",
 				"speed"
 			],
-			"desc": "Pace of icon animations in menu <O=off | S=slow | M=medium | F=fast>"
+			"desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)"
 		},
 		"PowerPulseWait": {
 			"text2": [