S60 Support (#1692)

* Mock S60

* cleanup

* Start refactor of OLED init

* Setup timers roughly

* Set Vector table offset correctly

Update system_stm32f1xx.c

* Update OLED.cpp

* Update stm32f1xx_hal_msp.c

* Update configuration.h

* I2C init before GPIO

From Errata

Update stm32f1xx_hal_msp.c

Update Software_I2C.h

Allow no hardware I2C

* I2C BB run bus unlock at init

* cleanups

* Software I2C for now

* Mildly more graceful Interpolate

* Handle is powered by DC

Update Power.cpp

Update drawPowerSourceIcon.cpp

Update configuration.h

Update Setup.cpp

* Cleanup HomeScreen

* Segment remap oled at init

* Cleanup

* Update MOVThread.cpp

* Fix PWM Init

* Fix adc2 trigger

* Update configs

* Fixup warning

* Saner default config

* Update ThermoModel.cpp

* Util for current@voltage

* Hub238 warning

* Add hub238 handling in power mode

* Update USBPDDebug_FUSB.cpp

* HUSB238 debug

* Hook PSU Limit

* Use wrapping section of GRAM for scroll

Update OLED.hpp

* Update NTC table

* Fix HUB voltage picker

* Cleanup

* Larger tip filter

* Calibrate in a bunch closer

Update ThermoModel.cpp

* Update configuration.h

* Update HUB238.cpp

* Update configuration.h

* Movement Pin

* Update BSP.cpp

* tim2 irq

* Rough timer conversion (adc broken) but movement working

* Fix tim2 start

* Faster base PWM

* Ensure utils grabs config

* Add wattage limiter tolerance for device

* Speed up PWM and enable PWM current limiting

* tune for 12v

* Prevent start until PD done

* Update configuration.h

* Add HUB238 check for have re-negotiated

* Adjust timer to avoid noise when its possible

source/Core/BSP/Sequre_S60/Pins.h

@@ -0,0 +1,43 @@
+/*
+ * Pins.h
+ *
+ *  Created on: 29 May 2020
+ *      Author: Ralim
+ */
+
+#ifndef BSP_MINIWARE_PINS_H_
+#define BSP_MINIWARE_PINS_H_
+#include "configuration.h"
+
+#ifdef MODEL_S60
+
+#define KEY_B_Pin             GPIO_PIN_1
+#define KEY_B_GPIO_Port       GPIOB
+#define TMP36_INPUT_Pin       GPIO_PIN_5
+#define TMP36_INPUT_GPIO_Port GPIOA
+#define TMP36_ADC1_CHANNEL    ADC_CHANNEL_5
+#define TMP36_ADC2_CHANNEL    ADC_CHANNEL_5
+#define TIP_TEMP_Pin          GPIO_PIN_0
+#define TIP_TEMP_GPIO_Port    GPIOA
+#define TIP_TEMP_ADC1_CHANNEL ADC_CHANNEL_0
+#define TIP_TEMP_ADC2_CHANNEL ADC_CHANNEL_0
+#define VIN_Pin               GPIO_PIN_4
+#define VIN_GPIO_Port         GPIOA
+#define VIN_ADC1_CHANNEL      ADC_CHANNEL_4
+#define VIN_ADC2_CHANNEL      ADC_CHANNEL_4
+#define KEY_A_Pin             GPIO_PIN_0
+#define KEY_A_GPIO_Port       GPIOB
+#define PWM_Out_Pin           GPIO_PIN_8
+#define PWM_Out_GPIO_Port     GPIOB
+#define PWM_Out_CHANNEL       TIM_CHANNEL_3 // Timer 4; channel 3
+#define SCL2_Pin              GPIO_PIN_6
+#define SCL2_GPIO_Port        GPIOB
+#define SDA2_Pin              GPIO_PIN_7
+#define SDA2_GPIO_Port        GPIOB
+// Pin gets pulled high on movement
+#define MOVEMENT_Pin       GPIO_PIN_3
+#define MOVEMENT_GPIO_Port GPIOA
+
+#endif
+
+#endif /* BSP_MINIWARE_PINS_H_ */