diff --git a/Documentation/Settings.md b/Documentation/Settings.md index ebcdaa6a..9faaf675 100644 --- a/Documentation/Settings.md +++ b/Documentation/Settings.md @@ -109,7 +109,7 @@ On device help text: Temperature used in "boost mode" -### Setting: Heat on power up +### Setting: Start-up behavior When the device powers up, should it enter into a special mode. These settings set it to either start into soldering mode, sleeping mode or auto mode (Enters into soldering mode on the first movement). @@ -117,7 +117,7 @@ On device help text: O=off | S=soldering temp | Z=standby at sleep temp until moved | R=standby without heating until moved -### Setting: Cooldown blink +### Setting: Cooldown flashing If the idle screen should blink the tip temperature for attention while the tip is over 50°C. Intended as a 'tip is still hot' warning. @@ -133,13 +133,13 @@ On device help text: Start tip temperature offset calibration -### Setting: Factory reset? +### Setting: Restore factory settings? Resets all settings and calibrations to factory defaults. Does NOT erase custom user boot up logo's. On device help text: -Reset settings to default +Reset all settings to default ### Setting: Calibrate input voltage? @@ -189,7 +189,7 @@ On device help text: Maximum power the iron can use (W=watt) -### Setting: Reverse + - keys +### Setting: Swap + - keys Swaps which button increments and decrements on temperature change screens. @@ -285,7 +285,7 @@ On device help text: Current firmware language -### Setting: Screen contrast +### Setting: Screen brightness Display brightness. Higher values age the OLED faster due to burn-in. (However, it is notable that most of these screens die from other causes first.) @@ -300,3 +300,15 @@ Inverts the entire OLED. On device help text: Invert the colours of the OLED screen + +### Setting: Boot logo duration + +Sets the duration of the boot logo from 1 second to 4 seconds. +- For static images this sets the time the logo is displayed for. +- For animations this sets the time the last frame is displayed for after the animation has been played. + +The infinity icon sets a logo or the last frame of an animation to be displayed until a button is pressed. + +On device help text: + +Sets the duration for the boot logo (S=seconds) diff --git a/Translations/translation_BE.json b/Translations/translation_BE.json index 87de0dee..1217b99b 100644 --- a/Translations/translation_BE.json +++ b/Translations/translation_BE.json @@ -2,26 +2,17 @@ "languageCode": "BE", "languageLocalName": "Беларуская", "fonts": ["ascii_basic", "latin_extended", "cyrillic"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Каліброўка закончана!", "SettingsCalibrationWarning": "Перад тым, як працягнуць, каліласка, упэўнецеся, што джала мае комнатную тэмпературу!", "SettingsResetWarning": "Вы ўпэннены, што жадаеце зкінуць налады да першапачатковых значэнняў?", "UVLOWarningString": "НАПРУГА--", "UndervoltageString": "Нізкая напруга", "InputVoltageString": "Сілкаванне В: ", - "WarningTipTempString": "Тэмп. джала: ", - "BadTipString": "ДЖАЛА--", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Чаканне...", - "WarningSimpleString": "ГОРАЧА!", - "WarningAdvancedString": "!!! ГАРАЧАЕ !!!\n!!! ДЖАЛА !!!", "SleepingTipAdvancedString": "Джала:", - "IdleTipString": "Джала:", - "IdleSetString": " ->", - "TipDisconnectedString": "ДЖАЛА АДЛУЧАНА", - "SolderingAdvancedPowerPrompt": "Сілкаванне: ", - "OffString": "Выкл.", - "YourGainMessage": "Прырост:" + "OffString": "Выкл." }, "messagesWarn": { "ResetOKMessage": "Скід OK", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "В", "SettingLockDisableChar": "А", "SettingLockBoostChar": "Т", - "SettingLockFullChar": "П", - "SettingNAChar": "Н/Д" + "SettingLockFullChar": "П" }, "menuGroups": { "PowerMenu": { @@ -208,6 +198,10 @@ "ColourInversion": { "text2": ["Экран", "Інвертаваць"], "desc": "Інвертаваць колеры OLED-экрана" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_BG.json b/Translations/translation_BG.json index d4f5d9fc..501c3aca 100644 --- a/Translations/translation_BG.json +++ b/Translations/translation_BG.json @@ -2,33 +2,24 @@ "languageCode": "BG", "languageLocalName": "Български", "fonts": ["ascii_basic", "cyrillic"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Калибрацията завършена!", "SettingsCalibrationWarning": "Уверете се, че върха на поялника е със стайна температура преди да продължите!", "SettingsResetWarning": "Сигурни ли сте, че искате да върнете фабричните настройки?", "UVLOWarningString": "Ниско DC Напрежение", "UndervoltageString": "Ниско Напрежение", "InputVoltageString": "Входно V: ", - "WarningTipTempString": "Темп.: ", - "BadTipString": "ЛОШ ВРЪХ", "SleepingSimpleString": "Сън", "SleepingAdvancedString": "Хър Хър Хър...", - "WarningSimpleString": "ОХ!", - "WarningAdvancedString": "ВНИМАНИЕ! ТОПЛО!", "SleepingTipAdvancedString": "Връх:", - "IdleTipString": "Връх:", - "IdleSetString": " Настройка:", - "TipDisconnectedString": "ПРЕКЪСНАТ ВРЪХ", - "SolderingAdvancedPowerPrompt": "Захранване: ", - "OffString": "Изкл.", - "YourGainMessage": "Усилване:" + "OffString": "Изкл." }, "messagesWarn": { "ResetOKMessage": "Нулиране", "SettingsResetMessage": ["Настройките бяха", "нулирани!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -45,15 +36,13 @@ "SettingStartSolderingChar": "Р", "SettingStartSleepChar": "С", "SettingStartSleepOffChar": "П", - "SettingStartNoneChar": "F", "SettingSensitivityOff": "O", "SettingSensitivityLow": "L", "SettingSensitivityMedium": "M", "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -148,7 +137,7 @@ }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { "text2": ["Лимит на", "мощност"], @@ -171,12 +160,12 @@ "desc": "Поддържане на интензивност на захранващия импулс" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Изключено | 1=Слабо | ... | 9=Силно)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Изключено | 1=Слабо | ... | 9=Силно)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -184,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2,5с)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2,5с)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -203,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_CS.json b/Translations/translation_CS.json index e2ecb384..087cd479 100644 --- a/Translations/translation_CS.json +++ b/Translations/translation_CS.json @@ -2,33 +2,24 @@ "languageCode": "CS", "languageLocalName": "Český", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibrace dokončena!", "SettingsCalibrationWarning": "Ujistěte se, že hrot má pokojovou teplotu!", "SettingsResetWarning": "Opravdu chcete resetovat zařízení do továrního nastavení?", "UVLOWarningString": "Nízké DC", "UndervoltageString": "! Nízké napětí !", "InputVoltageString": "Napětí: ", - "WarningTipTempString": "Teplota: ", - "BadTipString": "ŠP. HROT", "SleepingSimpleString": "Zzz ", "SleepingAdvancedString": "Režim spánku...", - "WarningSimpleString": "PÁLÍ", - "WarningAdvancedString": "!! HORKÝ HROT !!", "SleepingTipAdvancedString": "Hrot:", - "IdleTipString": "Hrot:", - "IdleSetString": " Cíl:", - "TipDisconnectedString": "HROT NEPŘIPOJEN", - "SolderingAdvancedPowerPrompt": "Ohřev: ", - "OffString": "Vyp", - "YourGainMessage": "Zisk:" + "OffString": "Vyp" }, "messagesWarn": { "ResetOKMessage": "Reset OK", "SettingsResetMessage": ["Tov. nas. obnov.", ""], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -170,12 +160,12 @@ "desc": "Puls pro udržení zařízení v chodu (kvůli power bankám)." }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Vyp | 1=Min | ... | 9=Max)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Vyp | 1=Min | ... | 9=Max)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | P=slow | M=medium | R=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2,5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2,5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_DA.json b/Translations/translation_DA.json index b16e3f01..7f1b8c5c 100644 --- a/Translations/translation_DA.json +++ b/Translations/translation_DA.json @@ -2,33 +2,24 @@ "languageCode": "DA", "languageLocalName": "Dansk", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Calibration done!", "SettingsCalibrationWarning": "Sørg for at loddespidsen er ved stuetemperatur, inden du fortsætter!", "SettingsResetWarning": "Are you sure to reset settings to default values?", "UVLOWarningString": "Lav Volt", "UndervoltageString": "Undervoltage", "InputVoltageString": "Input V: ", - "WarningTipTempString": "Tip Temp: ", - "BadTipString": "BAD TIP", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Dvale...", - "WarningSimpleString": "Varm", - "WarningAdvancedString": "VARM LODDESPIDS!", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "TIP DISCONNECTED", - "SolderingAdvancedPowerPrompt": "Power: ", - "OffString": "Off", - "YourGainMessage": "Your gain:" + "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -60,20 +50,20 @@ "desc": "Power settings" }, "SolderingMenu": { - "text2": ["Soldering", "Settings"], + "text2": ["Soldering", "settings"], "desc": "Soldering settings" }, "PowerSavingMenu": { - "text2": ["Sleep", "Modes"], - "desc": "Power Saving Settings" + "text2": ["Sleep", "mode"], + "desc": "Power saving settings" }, "UIMenu": { - "text2": ["User", "Interface"], - "desc": "User Interface settings" + "text2": ["User", "interface"], + "desc": "User interface settings" }, "AdvancedMenu": { - "text2": ["Advanced", "Options"], - "desc": "Advanced options" + "text2": ["Advanced", "settings"], + "desc": "Advanced settings" } }, "menuOptions": { @@ -114,11 +104,11 @@ "desc": "Temperatur i \"boost\" mode" }, "AutoStart": { - "text2": ["Auto", "start"], + "text2": ["Start-up", "behavior"], "desc": "Start automatisk med lodning når strøm sættes til. (S=Slukket | L=Lodning | D=Dvale tilstand | R=Dvale tilstand rumtemperatur)" }, "CooldownBlink": { - "text2": ["Cooldown", "blink"], + "text2": ["Cooldown", "flashing"], "desc": "Blink temperaturen på skærmen, mens spidsen stadig er varm." }, "TemperatureCalibration": { @@ -126,7 +116,7 @@ "desc": "kalibrere spids temperatur." }, "SettingsReset": { - "text2": ["Factory", "Reset?"], + "text2": ["Restore factory", "settings?"], "desc": "Gendan alle indstillinger" }, "VoltageCalibration": { @@ -139,43 +129,43 @@ }, "ScrollingSpeed": { "text2": ["Scrolling", "speed"], - "desc": "Speed this text scrolls past at" + "desc": "Speed info text scrolls past at (S=slow | F=fast)" }, "QCMaxVoltage": { - "text2": ["Power", "Wattage"], - "desc": "Power Wattage of the power adapter used" + "text2": ["QC", "voltage"], + "desc": "Max QC voltage the iron should negotiate for" }, "PDNegTimeout": { "text2": ["PD", "timeout"], "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Slukket | 1=Mindst følsom | ... | 9=Mest følsom)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Slukket | 1=Mindst følsom | ... | 9=Mest følsom)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2,5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2,5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_DE.json b/Translations/translation_DE.json index b9d6e675..2aada270 100644 --- a/Translations/translation_DE.json +++ b/Translations/translation_DE.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Ruhemodus...", "SleepingTipAdvancedString": "Temp:", - "IdleTipString": "Ist:", - "IdleSetString": " Soll:", - "TipDisconnectedString": "Spitze fehlt", - "SolderingAdvancedPowerPrompt": "Leistung: ", "OffString": "Aus" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "A", "SettingLockBoostChar": "B", - "SettingLockFullChar": "V", - "SettingNAChar": "-" + "SettingLockFullChar": "V" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": ["Farben", "umkehren"], "desc": "Invertiert die Farben des OLED-Displays" + }, + "LOGOTime": { + "text2": ["Startlogo-", "dauer"], + "desc": "Legt die Dauer der Anzeige des Startlogos fest (S=Sekunden)" } } } diff --git a/Translations/translation_EL.json b/Translations/translation_EL.json index ddbc5f24..66fcb3e6 100644 --- a/Translations/translation_EL.json +++ b/Translations/translation_EL.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Υπνος...", "SleepingTipAdvancedString": "Μύτη:", - "IdleTipString": "Μύτη:", - "IdleSetString": " Set:", - "TipDisconnectedString": "ΧΩΡΙΣ ΜΥΤΗ", - "SolderingAdvancedPowerPrompt": "Ενέργεια: ", "OffString": "Απ." }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "Υ", "SettingLockDisableChar": "Α", "SettingLockBoostChar": "B", - "SettingLockFullChar": "Π", - "SettingNAChar": "Δ/Δ" + "SettingLockFullChar": "Π" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": ["Αντιστροφή", "χρωμάτων"], "desc": "Αντιστροφή χρωμάτων οθόνης OLED" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_EN.json b/Translations/translation_EN.json index 3a1e3696..a5554111 100644 --- a/Translations/translation_EN.json +++ b/Translations/translation_EN.json @@ -12,15 +12,11 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Sleeping...", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "NO TIP", - "SolderingAdvancedPowerPrompt": "Power: ", "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Some settings", "changed"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], "LockingKeysString": "LOCKED", @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -106,14 +101,14 @@ }, "BoostTemperature": { "text2": ["Boost", "temp"], - "desc": "Temperature used in \"boost mode\"" + "desc": "Tip temperature used in \"boost mode\"" }, "AutoStart": { - "text2": ["Heat", "on power up"], - "desc": "O=off | S=soldering temp | Z=standby at sleep temp until moved | R=standby without heating until moved" + "text2": ["Start-up", "behavior"], + "desc": "O=off | S=heat up to soldering temp | Z=standby at sleep temp until moved | R=standby without heating until moved" }, "CooldownBlink": { - "text2": ["Cooldown", "blink"], + "text2": ["Cooldown", "flashing"], "desc": "Flash the temperature reading after heating was halted while the tip is still hot" }, "TemperatureCalibration": { @@ -121,8 +116,8 @@ "desc": "Start tip temperature offset calibration" }, "SettingsReset": { - "text2": ["Factory", "reset?"], - "desc": "Reset settings to default" + "text2": ["Restore factory", "settings?"], + "desc": "Reset all settings to default" }, "VoltageCalibration": { "text2": ["Calibrate", "input voltage?"], @@ -149,7 +144,7 @@ "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Reverse", "+ - keys"], + "text2": ["Swap", "+ - keys"], "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { @@ -197,12 +192,16 @@ "desc": "Current firmware language" }, "Brightness": { - "text2": ["Screen", "contrast"], + "text2": ["Screen", "brightness"], "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_ES.json b/Translations/translation_ES.json index e641e26a..e959479a 100644 --- a/Translations/translation_ES.json +++ b/Translations/translation_ES.json @@ -2,27 +2,17 @@ "languageCode": "ES", "languageLocalName": "Castellano", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "¡Calibrada!", "SettingsCalibrationWarning": "¡Asegúrate que la punta esté a temperatura ambiente antes de empezar!", "SettingsResetWarning": "¿Quieres restablecer los ajustes?", "UVLOWarningString": "CC BAJA", "UndervoltageString": "Voltaje bajo", "InputVoltageString": "Voltaje: ", - "WarningTipTempString": "Temp punta: ", - "BadTipString": "PT. ROTA", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "En reposo...", - "WarningSimpleString": "QUEMA", - "WarningAdvancedString": "¡LA PUNTA QUEMA!", "SleepingTipAdvancedString": "Punta:", - "IdleTipString": "Punta:", - "IdleSetString": " Aj:", - "TipDisconnectedString": "NO HAY PUNTA", - "SolderingAdvancedPowerPrompt": "Potencia: ", - "OffString": " No", - "YourGainMessage": "Gananc.:", - "SettingsResetMessage": "Ajustes borrados" + "OffString": " No" }, "messagesWarn": { "ResetOKMessage": "Hecho.", @@ -52,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -188,7 +177,7 @@ }, "AnimSpeed": { "text2": ["Anim.", "velocidad"], - "desc": "Velocidad de las animaciones de los iconos en el menú (O=off | L=low | M=medium | H=high)" + "desc": "Velocidad de las animaciones de los iconos en el menú (O=off | L=low | M=medium | R=high)" }, "PowerPulseWait": { "text2": ["Impulso de potencia", "tiempo de espera"], @@ -203,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_FI.json b/Translations/translation_FI.json index 223223a0..51ea7e83 100644 --- a/Translations/translation_FI.json +++ b/Translations/translation_FI.json @@ -2,24 +2,16 @@ "languageCode": "FI", "languageLocalName": "Suomi", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibrointi tehty!", "SettingsCalibrationWarning": "Varmista että kärki on huoneenlämpöinen ennen jatkamista!", "SettingsResetWarning": "Haluatko varmasti palauttaa oletusarvot?", "UVLOWarningString": "DC ALH.", "UndervoltageString": "Alijännite", "InputVoltageString": "Jännite: ", - "WarningTipTempString": "Kärjet lämpö: ", - "BadTipString": "PAHA KÄRJET", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Lepotila...", - "WarningSimpleString": "KUUMA!", - "WarningAdvancedString": "!!! KUUMA KÄRJET !!!", "SleepingTipAdvancedString": "Kärki:", - "IdleTipString": "Pää:", - "IdleSetString": "Aseta:", - "TipDisconnectedString": "KÄRKI PUUTTUU", - "SolderingAdvancedPowerPrompt": "Teho: ", "OffString": "Off" }, "messagesWarn": { @@ -37,9 +29,9 @@ "SettingLeftChar": "V", "SettingAutoChar": "A", "SettingOffChar": "P", - "SettingSlowChar": "H", + "SettingSlowChar": "A", "SettingMediumChar": "M", - "SettingFastChar": "N", + "SettingFastChar": "S", "SettingStartNoneChar": "E", "SettingStartSolderingChar": "J", "SettingStartSleepChar": "L", @@ -50,8 +42,7 @@ "SettingSensitivityHigh": "S", "SettingLockDisableChar": "P", "SettingLockBoostChar": "V", - "SettingLockFullChar": "K", - "SettingNAChar": "N/A" + "SettingLockFullChar": "K" }, "menuGroups": { "PowerMenu": { @@ -201,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_FR.json b/Translations/translation_FR.json index 22740a7d..d40c0c3e 100644 --- a/Translations/translation_FR.json +++ b/Translations/translation_FR.json @@ -2,26 +2,17 @@ "languageCode": "FR", "languageLocalName": "Français", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Calibration effectuée !", "SettingsCalibrationWarning": "Assurez-vous que la panne soit à température ambiante avant de continuer !", "SettingsResetWarning": "Voulez-vous vraiment réinitialiser les paramètres aux valeurs par défaut ?", "UVLOWarningString": "DC FAIBL", "UndervoltageString": "Sous-tension", "InputVoltageString": "V d'entrée: ", - "WarningTipTempString": "Temp. Panne : ", - "BadTipString": "PANNE HS", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "En veille...", - "WarningSimpleString": "CHAUD !", - "WarningAdvancedString": "ATTENTION ! CHAUD !", "SleepingTipAdvancedString": "Panne:", - "IdleTipString": "Act:", - "IdleSetString": " Reg:", - "TipDisconnectedString": "PANNE DÉBRANCHÉE", - "SolderingAdvancedPowerPrompt": "Puiss.:", - "OffString": "Off", - "YourGainMessage": "Gain : " + "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "V", - "SettingNAChar": "N/A" + "SettingLockFullChar": "V" }, "menuGroups": { "PowerMenu": { @@ -208,6 +198,10 @@ "ColourInversion": { "text2": ["Inverser", "les couleurs"], "desc": "Inverser les couleurs de l'écran OLED" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_HR.json b/Translations/translation_HR.json index ba8edb20..6971723c 100644 --- a/Translations/translation_HR.json +++ b/Translations/translation_HR.json @@ -2,33 +2,24 @@ "languageCode": "HR", "languageLocalName": "Hrvatski", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibracija gotova!", "SettingsCalibrationWarning": "Provjerite da je vršak ohlađen na sobnu temperaturu prije nego što nastavite!", "SettingsResetWarning": "Jeste li sigurni da želite sve postavke vratiti na tvorničke vrijednosti?", "UVLOWarningString": "BATERIJA", "UndervoltageString": "PRENIZAK NAPON", "InputVoltageString": "Napajanje: ", - "WarningTipTempString": "Temp vrha: ", - "BadTipString": "LOŠ VRH", "SleepingSimpleString": "Zzz ", "SleepingAdvancedString": "SPAVANJE...", - "WarningSimpleString": "VRUĆ", - "WarningAdvancedString": "OPREZ, VRUĆE!", "SleepingTipAdvancedString": "Vrh: ", - "IdleTipString": "Vrh: ", - "IdleSetString": " / ", - "TipDisconnectedString": "VRH NIJE SPOJEN!", - "SolderingAdvancedPowerPrompt": "Snaga: ", - "OffString": "Off", - "YourGainMessage": "Your gain:" + "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -147,51 +137,51 @@ }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Ugašeno | 1=Najmanje osjetljivo | ... | 9=Najosjetljivije)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Ugašeno | 1=Najmanje osjetljivo | ... | 9=Najosjetljivije)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], - "desc": "Minimum allowed voltage per cell (3S: 3 - 3.7V, 4-6S: 2.4 - 3.7V)" + "desc": "Minimum allowed voltage per cell (3S: 3 - 3.7V | 4-6S: 2.4 - 3.7V)" }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | B=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_HU.json b/Translations/translation_HU.json index 137ea1b2..e4dcaef2 100644 --- a/Translations/translation_HU.json +++ b/Translations/translation_HU.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Alvás...", "SleepingTipAdvancedString": "Hegy:", - "IdleTipString": "Hegy:", - "IdleSetString": " Cél:", - "TipDisconnectedString": "HEGY KIVÉVE", - "SolderingAdvancedPowerPrompt": "Áram: ", "OffString": "Ki" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "M", "SettingLockDisableChar": "K", "SettingLockBoostChar": "B", - "SettingLockFullChar": "T", - "SettingNAChar": "N/A" + "SettingLockFullChar": "T" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": ["Képernyő", "invertálás"], "desc": "Képernyő színeinek invertálása" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_IT.json b/Translations/translation_IT.json index 6298f1d2..58a04493 100644 --- a/Translations/translation_IT.json +++ b/Translations/translation_IT.json @@ -2,6 +2,7 @@ "languageCode": "IT", "languageLocalName": "Italiano", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { "SettingsCalibrationWarning": "Assicurarsi che la punta si trovi a temperatura ambiente prima di continuare!", "SettingsResetWarning": "Ripristinare le impostazioni iniziali?", @@ -11,10 +12,6 @@ "SleepingSimpleString": "Zzz ", "SleepingAdvancedString": "Riposo", "SleepingTipAdvancedString": "Punta:", - "IdleTipString": "T punta:", - "IdleSetString": "/", - "TipDisconnectedString": "PUNTA ASSENTE", - "SolderingAdvancedPowerPrompt": "Potenz:", "OffString": "OFF" }, "messagesWarn": { @@ -45,8 +42,7 @@ "SettingSensitivityHigh": "A", "SettingLockDisableChar": "D", "SettingLockBoostChar": "T", - "SettingLockFullChar": "C", - "SettingNAChar": " NA" + "SettingLockFullChar": "C" }, "menuGroups": { "PowerMenu": { @@ -202,6 +198,10 @@ "ColourInversion": { "text2": ["Inverti", "colori"], "desc": "Inverti i colori dello schermo" + }, + "LOGOTime": { + "text2": ["Durata", "logo"], + "desc": "Imposta la permanenza sullo schermo del logo iniziale [secondi]" } } } diff --git a/Translations/translation_JA_JP.json b/Translations/translation_JA_JP.json index 4c4a0744..ad07bda5 100755 --- a/Translations/translation_JA_JP.json +++ b/Translations/translation_JA_JP.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Sleeping...", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "NO TIP", - "SolderingAdvancedPowerPrompt": "Power: ", "OffString": "オフ" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "高", "SettingLockDisableChar": "×", "SettingLockBoostChar": "ブ", - "SettingLockFullChar": "全", - "SettingNAChar": "非適用" + "SettingLockFullChar": "全" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": "色反転", "desc": "画面の色を反転する" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_LT.json b/Translations/translation_LT.json index f9141900..c7fe020d 100644 --- a/Translations/translation_LT.json +++ b/Translations/translation_LT.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Miegu...", "SleepingTipAdvancedString": "Antg:", - "IdleTipString": "Ant:", - "IdleSetString": " Nust:", - "TipDisconnectedString": "NĖRA ANTGALIO", - "SolderingAdvancedPowerPrompt": "Galia: ", "OffString": "Išj" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "A", "SettingLockDisableChar": "I", "SettingLockBoostChar": "T", - "SettingLockFullChar": "V", - "SettingNAChar": "N/A" + "SettingLockFullChar": "V" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": ["Ekrano", "invertavimas"], "desc": "Invertuoja OLED ekrano spalvas" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_NL.json b/Translations/translation_NL.json index c1887944..bc9172cd 100644 --- a/Translations/translation_NL.json +++ b/Translations/translation_NL.json @@ -2,26 +2,17 @@ "languageCode": "NL", "languageLocalName": "Nederlands", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Calibratie klaar!", "SettingsCalibrationWarning": "Zorg ervoor dat te punt op kamertemperatuur is voor je verder gaat!", "SettingsResetWarning": "Weet je zeker dat je de fabrieksinstellingen terug wil zetten?", "UVLOWarningString": "DC Laag", "UndervoltageString": "Onderspanning", "InputVoltageString": "Input V: ", - "WarningTipTempString": "Punt temp: ", - "BadTipString": "DEFECTE PUNT", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Slaapstand...", - "WarningSimpleString": "HEET!", - "WarningAdvancedString": "!!! PUNT HOT !!!", "SleepingTipAdvancedString": "Punt:", - "IdleTipString": "Punt:", - "IdleSetString": " Zet:", - "TipDisconnectedString": "PUNT LOSGEKOPPELT", - "SolderingAdvancedPowerPrompt": "Vermogen: ", - "OffString": "Uit", - "YourGainMessage": "Niveau:" + "OffString": "Uit" }, "messagesWarn": { "ResetOKMessage": "Reset OK", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "U", "SettingLockBoostChar": "B", - "SettingLockFullChar": "V", - "SettingNAChar": "N/A" + "SettingLockFullChar": "V" }, "menuGroups": { "PowerMenu": { @@ -170,8 +160,8 @@ "desc": "Vermogen van puls om soldeerbout aan te houden" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=uit | 1=minst gevoelig | ... | 9=meest gevoelig)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=uit | 1=minst gevoelig | ... | 9=meest gevoelig)" }, "LockingMode": { "text2": ["Blokkeer", "knoppen"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_NL_BE.json b/Translations/translation_NL_BE.json index e025871c..c8a3aa57 100644 --- a/Translations/translation_NL_BE.json +++ b/Translations/translation_NL_BE.json @@ -2,33 +2,24 @@ "languageCode": "NL_BE", "languageLocalName": "Vlaams", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Gecalibreerd!", "SettingsCalibrationWarning": "Zorg vooraf dat de punt op kamertemperatuur is!", "SettingsResetWarning": "Ben je zeker dat je alle standaardwaarden wil resetten?", "UVLOWarningString": "Voedingsspanning LAAG", "UndervoltageString": "Onderspanning", "InputVoltageString": "Voedingsspanning: ", - "WarningTipTempString": "Punt Temp: ", - "BadTipString": "DEFECT", "SleepingSimpleString": "Zzz ", "SleepingAdvancedString": "Slaapstand...", - "WarningSimpleString": "HEET", - "WarningAdvancedString": "!!! PUNT HEET !!!", "SleepingTipAdvancedString": "Punt:", - "IdleTipString": "Punt:", - "IdleSetString": "Stel in:", - "TipDisconnectedString": "Punt ONTKOPPELD", - "SolderingAdvancedPowerPrompt": "Vermogen: ", - "OffString": "Uit", - "YourGainMessage": "Your gain:" + "OffString": "Uit" }, "messagesWarn": { "ResetOKMessage": "Reset OK", "SettingsResetMessage": ["Settings were", "reset!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -147,35 +137,35 @@ }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=uit | 1=minst gevoelig | ... | 9=meest gevoelig)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=uit | 1=minst gevoelig | ... | 9=meest gevoelig)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | T=slow | M=medium | S=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_NO.json b/Translations/translation_NO.json index a2672593..5da114a5 100644 --- a/Translations/translation_NO.json +++ b/Translations/translation_NO.json @@ -2,33 +2,24 @@ "languageCode": "NO", "languageLocalName": "Norsk", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Calibration done!", "SettingsCalibrationWarning": "Sørg for at loddespissen har romtemperatur før du fortsetter!", "SettingsResetWarning": "Er du sikker på at du vil tilbakestille til standardinnstillinger?", "UVLOWarningString": "Lavspenn", "UndervoltageString": "Underspenning", "InputVoltageString": "Innspenn.: ", - "WarningTipTempString": "Spisstemp: ", - "BadTipString": "BAD TIP", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Dvale...", - "WarningSimpleString": "Varm", - "WarningAdvancedString": "VARM SPISS!", "SleepingTipAdvancedString": "Spiss:", - "IdleTipString": "Spiss:", - "IdleSetString": "Set:", - "TipDisconnectedString": "SPISS FRAKOBLET", - "SolderingAdvancedPowerPrompt": "Effekt: ", - "OffString": "Av", - "YourGainMessage": "Your gain:" + "OffString": "Av" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], - "LockingKeysString": " LOCKED", + "LockingKeysString": "LOCKED", "UnlockingKeysString": "UNLOCKED", "WarningKeysLockedString": "!LOCKED!", "WarningThermalRunaway": ["Thermal", "Runaway"] @@ -38,9 +29,9 @@ "SettingLeftChar": "V", "SettingAutoChar": "A", "SettingOffChar": "O", - "SettingSlowChar": "L", + "SettingSlowChar": "S", "SettingMediumChar": "M", - "SettingFastChar": "H", + "SettingFastChar": "F", "SettingStartNoneChar": "I", "SettingStartSolderingChar": "L", "SettingStartSleepChar": "D", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -142,40 +132,40 @@ "desc": "Hastigheten på rulletekst" }, "QCMaxVoltage": { - "text2": ["Power", "Wattage"], - "desc": "Power Wattage of the power adapter used" + "text2": ["QC", "voltage"], + "desc": "Max QC voltage the iron should negotiate for" }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Inaktiv | 1=Minst følsom | ... | 9=Mest følsom)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Inaktiv | 1=Minst følsom | ... | 9=Mest følsom)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_PL.json b/Translations/translation_PL.json index 7db7211a..ad55b4cc 100644 --- a/Translations/translation_PL.json +++ b/Translations/translation_PL.json @@ -4,25 +4,15 @@ "fonts": ["ascii_basic", "latin_extended"], "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibracja udana!", "SettingsCalibrationWarning": "Przed kontynuowaniem upewnij się, że końcówka osiągnęła temperaturę pokojową!", "SettingsResetWarning": "Czy na pewno chcesz przywrócić ustawienia fabryczne?", "UVLOWarningString": "NIS. NAP", "UndervoltageString": "Zbyt niskie nap.", "InputVoltageString": "Nap. wej.:", - "WarningTipTempString": "Temp. grotu:", - "BadTipString": "ZŁY GROT", "SleepingSimpleString": "Zzz!", "SleepingAdvancedString": "Tr. uśpienia", - "WarningSimpleString": "HOT!", - "WarningAdvancedString": "GORĄCA KOŃCÓWKA!", "SleepingTipAdvancedString": "Grot:", - "IdleTipString": "Grot:", - "IdleSetString": " Ust:", - "TipDisconnectedString": "GROT ODŁĄCZONY", - "SolderingAdvancedPowerPrompt": "Moc: ", - "OffString": "Wył", - "YourGainMessage": "Us.zysk:" + "OffString": "Wył" }, "messagesWarn": { "ResetOKMessage": "Reset OK", @@ -52,8 +42,7 @@ "SettingSensitivityHigh": "W", "SettingLockDisableChar": "W", "SettingLockBoostChar": "B", - "SettingLockFullChar": "P", - "SettingNAChar": "N/D" + "SettingLockFullChar": "P" }, "menuGroups": { "PowerMenu": { @@ -188,7 +177,7 @@ }, "AnimSpeed": { "text2": ["Prędkosć", "animacji"], - "desc": "Prędkość animacji ikon w menu (O: wył. | L: mała | M: średnia | H: duża)" + "desc": "Prędkość animacji ikon w menu (O: wył. | W: mała | M: średnia | S: duża)" }, "PowerPulseWait": { "text2": ["Czas między", "imp. mocy"], @@ -209,6 +198,10 @@ "ColourInversion": { "text2": ["Odwrócenie", "kolorów"], "desc": "Odwrócenie kolorów wyświetlacza OLED" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_PT.json b/Translations/translation_PT.json index 892ef520..d898e02d 100644 --- a/Translations/translation_PT.json +++ b/Translations/translation_PT.json @@ -2,30 +2,21 @@ "languageCode": "PT", "languageLocalName": "Português", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Calibração terminada!", "SettingsCalibrationWarning": "A ponta deve estar à temperatura ambiente antes de continuar!", "SettingsResetWarning": "Definições de fábrica?", "UVLOWarningString": "DC BAIXO", "UndervoltageString": "Subtensão", "InputVoltageString": "Tensão ", - "WarningTipTempString": "Temperatura ", - "BadTipString": "ER PONTA", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Repouso...", - "WarningSimpleString": "TEMP", - "WarningAdvancedString": "TEMP ELEVADA!", "SleepingTipAdvancedString": "Ponta:", - "IdleTipString": "Ponta:", - "IdleSetString": " Aj:", - "TipDisconnectedString": "SEM PONTA", - "SolderingAdvancedPowerPrompt": "Power: ", - "OffString": "Off", - "YourGainMessage": "Your gain:" + "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], "LockingKeysString": "LOCKED", @@ -38,9 +29,9 @@ "SettingLeftChar": "C", "SettingAutoChar": "A", "SettingOffChar": "O", - "SettingSlowChar": "L", + "SettingSlowChar": "S", "SettingMediumChar": "M", - "SettingFastChar": "R", + "SettingFastChar": "F", "SettingStartNoneChar": "D", "SettingStartSolderingChar": "S", "SettingStartSleepChar": "H", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -150,7 +140,7 @@ "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" }, "PowerLimit": { - "text2": ["Power", "Limit"], + "text2": ["Power", "limit"], "desc": "Maximum power the iron can use (Watts)" }, "ReverseButtonTempChange": { @@ -187,11 +177,11 @@ }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_RO.json b/Translations/translation_RO.json index 3cef69cb..5d4dd1f8 100644 --- a/Translations/translation_RO.json +++ b/Translations/translation_RO.json @@ -4,25 +4,15 @@ "fonts": ["ascii_basic", "latin_extended"], "tempUnitFahrenheit": true, "messages": { - "SettingsCalibrationDone": "Calibrare completa!", "SettingsCalibrationWarning": "Vă rugăm să vă asigurati că vârful este la temperatura camerei, înainte de a continua!", "SettingsResetWarning": "Sigur doriti să restaurati la setările implicite?", "UVLOWarningString": "DC LOW", "UndervoltageString": "Sub tensiune", "InputVoltageString": "Intrare V: ", - "WarningTipTempString": "Temp. varf: ", - "BadTipString": "VARF DEFECT", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Adormit...", - "WarningSimpleString": "FIERBINTE!", - "WarningAdvancedString": "!!! VARF FIERBINTE !!!", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "FĂRĂ VARF", - "SolderingAdvancedPowerPrompt": "Putere: ", - "OffString": "Nu", - "YourGainMessage": "Coeficient:" + "OffString": "Nu" }, "messagesWarn": { "ResetOKMessage": "Reset OK", @@ -52,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -188,7 +177,7 @@ }, "AnimSpeed": { "text2": ["Animatii", "viteză"], - "desc": "Ritmul animatiilor pictogramei din meniu (O=oprit | S=încet | M=mediu | F=rapid)" + "desc": "Ritmul animatiilor pictogramei din meniu (O=oprit | Î=încet | M=mediu | R=rapid)" }, "PowerPulseWait": { "text2": ["Întârziere", "puls putere"], @@ -209,6 +198,10 @@ "ColourInversion": { "text2": ["Inverseaza", "culoarea"], "desc": "Inverseaza culoarea ecranului" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_RU.json b/Translations/translation_RU.json index fc98b928..c205bdef 100644 --- a/Translations/translation_RU.json +++ b/Translations/translation_RU.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Ожидание...", "SleepingTipAdvancedString": "Жало:", - "IdleTipString": "Жало:", - "IdleSetString": " ->", - "TipDisconnectedString": "ЖАЛО ОТСОЕДИНЕНО", - "SolderingAdvancedPowerPrompt": "Питание: ", "OffString": "Вык" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "В", "SettingLockDisableChar": "О", "SettingLockBoostChar": "Т", - "SettingLockFullChar": "П", - "SettingNAChar": "Н/Д" + "SettingLockFullChar": "П" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": ["Инверт", "экрана"], "desc": "Инвертировать цвета на OLED экране" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_SK.json b/Translations/translation_SK.json index d1864cf6..2baf818f 100644 --- a/Translations/translation_SK.json +++ b/Translations/translation_SK.json @@ -2,6 +2,7 @@ "languageCode": "SK", "languageLocalName": "Slovenčina", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { "SettingsCalibrationWarning": "Najprv sa prosím uistite, že hrot má izbovú teplotu!", "SettingsResetWarning": "Naozaj chcete obnoviť továrenské nastavenia?", @@ -11,10 +12,6 @@ "SleepingSimpleString": "Chrr", "SleepingAdvancedString": "Pokojový režim..", "SleepingTipAdvancedString": "Hrot:", - "IdleTipString": "Hrot:", - "IdleSetString": "Cieľ:", - "TipDisconnectedString": "HROT ODPOJENÝ", - "SolderingAdvancedPowerPrompt": "Výkon: ", "OffString": "Vyp" }, "messagesWarn": { @@ -45,8 +42,7 @@ "SettingSensitivityHigh": "V", "SettingLockDisableChar": "Z", "SettingLockBoostChar": "B", - "SettingLockFullChar": "P", - "SettingNAChar": "N/A" + "SettingLockFullChar": "P" }, "menuGroups": { "PowerMenu": { @@ -202,6 +198,10 @@ "ColourInversion": { "text2": ["Invertovať", "obrazovku"], "desc": "Invertovať farby OLED displeja" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_SL.json b/Translations/translation_SL.json index fc21e16b..9320b62f 100644 --- a/Translations/translation_SL.json +++ b/Translations/translation_SL.json @@ -2,26 +2,17 @@ "languageCode": "SL", "languageLocalName": "Slovenščina", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibracija opravljena!", "SettingsCalibrationWarning": "Pred nadaljevanjem mora biti konica segreta na sobno temperaturo!", "SettingsResetWarning": "Res želite ponastaviti na privzete nastavitve?", "UVLOWarningString": "NIZKA U", "UndervoltageString": "Nizka napetost", "InputVoltageString": "Vhodna U: ", - "WarningTipTempString": "Temp. kon.: ", - "BadTipString": "KONICA?", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Spim...", - "WarningSimpleString": "VROČ", - "WarningAdvancedString": "!!VROČA KONICA!!", "SleepingTipAdvancedString": "Konica", - "IdleTipString": "Kon:", - "IdleSetString": " temp:", - "TipDisconnectedString": "NI KONICE", - "SolderingAdvancedPowerPrompt": "Moč: ", - "OffString": "Off", - "YourGainMessage": "Ojačenje" + "OffString": "Off" }, "messagesWarn": { "ResetOKMessage": "Reset OK", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "V", "SettingLockDisableChar": "O", "SettingLockBoostChar": "L", - "SettingLockFullChar": "P", - "SettingNAChar": "N/A" + "SettingLockFullChar": "P" }, "menuGroups": { "PowerMenu": { @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | P=slow | M=medium | H=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_SR_CYRL.json b/Translations/translation_SR_CYRL.json index efe348ef..d50c7f54 100644 --- a/Translations/translation_SR_CYRL.json +++ b/Translations/translation_SR_CYRL.json @@ -2,30 +2,21 @@ "languageCode": "SR_CYRL", "languageLocalName": "Српски", "fonts": ["ascii_basic", "cyrillic"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Калибрација готова", "SettingsCalibrationWarning": "Проверите да ли је врх охлађен на собну температуру пре него што наставите", "SettingsResetWarning": "Да ли заиста желите да вратите поставке на фабричке вредности?", "UVLOWarningString": "НИЗ.НАП.", "UndervoltageString": "ПРЕНИЗАК НАПОН", "InputVoltageString": "Ул. напон: ", - "WarningTipTempString": "Темп. врха: ", - "BadTipString": "ЛОШ ВРХ", "SleepingSimpleString": "Сан", "SleepingAdvancedString": "Спавање...", - "WarningSimpleString": "ВРУЋ", - "WarningAdvancedString": "! ОПРЕЗ, ВРУЋЕ !", "SleepingTipAdvancedString": "Врх:", - "IdleTipString": "Врх:", - "IdleSetString": " / ", - "TipDisconnectedString": "ВРХ НИЈЕ СПОЈЕН", - "SolderingAdvancedPowerPrompt": "Снага: ", - "OffString": "Иск", - "YourGainMessage": "Your gain:" + "OffString": "Иск" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], "LockingKeysString": "LOCKED", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -147,35 +137,35 @@ }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=искључено | 1=најмање осетљиво | ... | 9=најосетљивије)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=искључено | 1=најмање осетљиво | ... | 9=најосетљивије)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | С=slow | M=medium | Б=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5с)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5с)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_SR_LATN.json b/Translations/translation_SR_LATN.json index 432f80f1..cef6a788 100644 --- a/Translations/translation_SR_LATN.json +++ b/Translations/translation_SR_LATN.json @@ -2,30 +2,21 @@ "languageCode": "SR_LATN", "languageLocalName": "Srpski", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibracija gotova", "SettingsCalibrationWarning": "Proverite da li je vrh ohlađen na sobnu temperaturu pre nego što nastavite", "SettingsResetWarning": "Da li zaista želite da vratite postavke na fabričke vrednosti?", "UVLOWarningString": "NIZ.NAP.", "UndervoltageString": "PRENIZAK NAPON", "InputVoltageString": "Ul. napon: ", - "WarningTipTempString": "Temp. vrha: ", - "BadTipString": "LOŠ VRH", "SleepingSimpleString": "Zzz", "SleepingAdvancedString": "Spavanje...", - "WarningSimpleString": "VRUĆ", - "WarningAdvancedString": "! OPREZ, VRUĆE !", "SleepingTipAdvancedString": "Vrh:", - "IdleTipString": "Vrh:", - "IdleSetString": " / ", - "TipDisconnectedString": "VRH NIJE SPOJEN", - "SolderingAdvancedPowerPrompt": "Snaga: ", - "OffString": "Isk", - "YourGainMessage": "Your gain:" + "OffString": "Isk" }, "messagesWarn": { "ResetOKMessage": "Reset OK", - "SettingsResetMessage": ["Settings were", "reset!"], + "SettingsResetMessage": ["Certain settings", "were changed!"], "NoAccelerometerMessage": ["No accelerometer", "detected!"], "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"], "LockingKeysString": "LOCKED", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "D", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -147,35 +137,35 @@ }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], - "desc": "Maximum power the iron can use (Watts)" + "text2": ["Power", "limit"], + "desc": "Maximum power the iron can use (W=watt)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], - "desc": "Reverse the tip temperature change buttons plus minus assignment." + "text2": ["Swap", "+ - keys"], + "desc": "Reverse assignment of buttons for temperature adjustment" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], - "desc": "Temperature change steps on short button press!" + "text2": ["Temp change", "short"], + "desc": "Temperature-change-increment on short button press" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], - "desc": "Temperature change steps on long button press!" + "text2": ["Temp change", "long"], + "desc": "Temperature-change-increment on long button press" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], - "desc": "Keep awake pulse power intensity" + "text2": ["Power", "pulse"], + "desc": "Intensity of power of keep-awake-pulse (watt)" }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=isključeno | 1=najmanje osetljivo | ... | 9=najosetljivije)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=isključeno | 1=najmanje osetljivo | ... | 9=najosetljivije)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -183,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | B=fast)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -202,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_SV.json b/Translations/translation_SV.json index 18e32cb6..e22c4734 100644 --- a/Translations/translation_SV.json +++ b/Translations/translation_SV.json @@ -2,6 +2,7 @@ "languageCode": "SV", "languageLocalName": "Svenska", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { "SettingsCalibrationWarning": "Se till att spetsen är rumstemererad innan du fortsätter!", "SettingsResetWarning": "Är du säker på att du vill återställa inställningarna?", @@ -11,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Viloläge...", "SleepingTipAdvancedString": "Spets:", - "IdleTipString": "Spts:", - "IdleSetString": " Ang:", - "TipDisconnectedString": "SPETS URTAGEN", - "SolderingAdvancedPowerPrompt": "Ström: ", "OffString": "Av" }, "messagesWarn": { @@ -45,8 +42,7 @@ "SettingSensitivityHigh": "H", "SettingLockDisableChar": "A", "SettingLockBoostChar": "T", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -184,8 +180,8 @@ "desc": "Animationshastighet för ikoner i menyer (A=av | L=långsam | M=medel | S=snabb)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -196,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_TR.json b/Translations/translation_TR.json index a335b9f9..2d65ae7d 100644 --- a/Translations/translation_TR.json +++ b/Translations/translation_TR.json @@ -2,26 +2,17 @@ "languageCode": "TR", "languageLocalName": "Türkçe", "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Kalibrasyon tamamlandı!", "SettingsCalibrationWarning": "Lütfen devam etmeden önce ucun oda sıcaklığında olduğunu garantiye alın!", "SettingsResetWarning": "Ayarları varsayılan değerlere sıfırlamak istediğinizden emin misiniz?", "UVLOWarningString": "Güç Az", "UndervoltageString": "Düşük Voltaj", "InputVoltageString": "Giriş V: ", - "WarningTipTempString": "Uç Sıcaklığı: ", - "BadTipString": "KÖTÜ UÇ", "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Bekleme Modu ...", - "WarningSimpleString": "SICAK!", - "WarningAdvancedString": "UYARI! UÇ SICAK!", "SleepingTipAdvancedString": "Uç:", - "IdleTipString": "Uç:", - "IdleSetString": " Ayarla:", - "TipDisconnectedString": "UÇ ÇIKARILDI", - "SolderingAdvancedPowerPrompt": "Güç: ", - "OffString": "Kapalı", - "YourGainMessage": "Kazancınız:" + "OffString": "Kapalı" }, "messagesWarn": { "ResetOKMessage": ["Sıfırlama Tamam", ""], @@ -36,23 +27,22 @@ "characters": { "SettingRightChar": "R", "SettingLeftChar": "L", - "SettingAutoChar": "A", - "SettingOffChar": "O", - "SettingSlowChar": "S", - "SettingMediumChar": "M", - "SettingFastChar": "F", + "SettingAutoChar": "O", + "SettingOffChar": "K", + "SettingSlowChar": "Y", + "SettingMediumChar": "O", + "SettingFastChar": "H", "SettingStartNoneChar": "K", "SettingStartSolderingChar": "L", "SettingStartSleepChar": "U", - "SettingStartSleepOffChar": "O", - "SettingSensitivityOff": "O", + "SettingStartSleepOffChar": "S", + "SettingSensitivityOff": "K", "SettingSensitivityLow": "L", - "SettingSensitivityMedium": "M", + "SettingSensitivityMedium": "O", "SettingSensitivityHigh": "H", - "SettingLockDisableChar": "D", + "SettingLockDisableChar": "K", "SettingLockBoostChar": "B", - "SettingLockFullChar": "F", - "SettingNAChar": "N/A" + "SettingLockFullChar": "F" }, "menuGroups": { "PowerMenu": { @@ -107,11 +97,7 @@ }, "DisplayRotation": { "text2": ["GRNYÖN", ""], - "desc": "Görüntü Yönlendirme (R=Sağlak | L=Solak | A=Otomatik)" - }, - "BoostEnabled": { - "text2": ["YÜKPER", ""], - "desc": "Lehimleme yaparken ön tuşa basmak anlık sıcaklık yükselişi sağlar. (450C)" + "desc": "Görüntü Yönlendirme (R=Sağlak | L=Solak | O=Otomatik)" }, "BoostTemperature": { "text2": ["YKSC", ""], @@ -119,7 +105,7 @@ }, "AutoStart": { "text2": ["OTOBAŞ", ""], - "desc": "Güç verildiğinde otomatik olarak lehimleme modunda başlat. (K=Kapalı | L=Lehimleme Modu | U=Uyku Modu | O=Uyku Modu Oda Sıcaklığı)" + "desc": "Güç verildiğinde otomatik olarak lehimleme modunda başlat. (K=Kapalı | L=Lehimleme Modu | U=Uyku Modu | S=Uyku Modu Oda Sıcaklığı)" }, "CooldownBlink": { "text2": ["SĞGÖST", ""], @@ -143,51 +129,43 @@ }, "ScrollingSpeed": { "text2": ["YZKYHZ", ""], - "desc": "Bu yazının kayma hızı (S=Yavaş | F=Hızlı)" + "desc": "Bu yazının kayma hızı (Y=Yavaş | H=Hızlı)" }, "QCMaxVoltage": { - "text2": ["QC", "Voltage"], - "desc": "Desired max QC Voltage negotiated for" + "text2": ["QC", "voltage"], + "desc": "Max QC voltage the iron should negotiate for" }, "PDNegTimeout": { "text2": ["PD", "timeout"], - "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)" - }, - "PowerInput": { - "text2": ["Güç", "Miktarı(W)"], - "desc": "Kullanılan adaptörün watt biriminden güç miktarı" - }, - "PowerLimitEnable": { - "text2": ["P Limit", "Enable"], - "desc": "Güç sınırlamayı aç" + "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers" }, "PowerLimit": { - "text2": ["Power", "Limit"], + "text2": ["Power", "limit"], "desc": "Havyanın kullanacağı en yüksek güç (Watts)" }, "ReverseButtonTempChange": { - "text2": ["Key +-", "reverse?"], + "text2": ["Swap", "+ - keys"], "desc": "\"Düğme Yerleri Rotasyonu\" Sıcaklık ayar düğmelerinin yerini değiştirin" }, "TempChangeShortStep": { - "text2": ["Temp change", "short?"], + "text2": ["Temp change", "short"], "desc": "Kısa basışlardaki sıcaklık derecesi atlama oranı" }, "TempChangeLongStep": { - "text2": ["Temp change", "long?"], + "text2": ["Temp change", "long"], "desc": "Uzun başışlardaki sıcaklık derecesi atlama oranı" }, "PowerPulsePower": { - "text2": ["Power", "Pulse W"], + "text2": ["Power", "pulse"], "desc": "Güç girişi voltajı ölçüm yoğunluğunu sık tut." }, "HallEffSensitivity": { - "text2": ["Hall Eff", "Sensitivity"], - "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Kapalı | 1=En az duyarlı | ... | 9=En duyarlı)" + "text2": ["Hall sensor", "sensitivity"], + "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Kapalı | 1=En az duyarlı | ... | 9=En duyarlı)" }, "LockingMode": { - "text2": ["Allow buttons", "locking"], - "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)" + "text2": ["Allow locking", "buttons"], + "desc": "While soldering, hold down both buttons to toggle locking them (K=Kapalı | B=boost mode only | F=full locking)" }, "MinVolCell": { "text2": ["Minimum", "voltage"], @@ -195,15 +173,15 @@ }, "AnimLoop": { "text2": ["Anim.", "loop"], - "desc": "Loop icon animations in root menu" + "desc": "Loop icon animations in main menu" }, "AnimSpeed": { "text2": ["Anim.", "speed"], - "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)" + "desc": "Pace of icon animations in menu (K=Kapalı | Y=Yavaş | O=Orta | H=Hızlı)" }, "PowerPulseWait": { - "text2": ["Power pulse", "wait time"], - "desc": "Time to wait before triggering every keep-awake pulse (x 2.5s)" + "text2": ["Power pulse", "delay"], + "desc": "Delay before keep-awake-pulse is triggered (x 2.5s)" }, "PowerPulseDuration": { "text2": ["Power pulse", "duration"], @@ -214,12 +192,16 @@ "desc": "" }, "Brightness": { - "text2": ["Screen", "Brightness"], - "desc": "Adjust the contrast/brightness of the OLED screen" + "text2": ["Screen", "brightness"], + "desc": "Adjust the brightness of the OLED screen" }, "ColourInversion": { - "text2": ["Screen", "Invert"], + "text2": ["Invert", "screen"], "desc": "Invert the colours of the OLED screen" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_UK.json b/Translations/translation_UK.json index 31def604..a476a527 100644 --- a/Translations/translation_UK.json +++ b/Translations/translation_UK.json @@ -2,26 +2,17 @@ "languageCode": "UK", "languageLocalName": "Українська", "fonts": ["ascii_basic", "latin_extended", "cyrillic"], + "tempUnitFahrenheit": false, "messages": { - "SettingsCalibrationDone": "Калібрування виконане!", "SettingsCalibrationWarning": "Переконайтеся, що жало охололо до кімнатної температури, перш ніж продовжувати!", "SettingsResetWarning": "Ви дійсно хочете скинути налаштування до значень за замовчуванням? (A=Так, В=Ні)", "UVLOWarningString": "АККУМ--", "UndervoltageString": "Низька напруга", "InputVoltageString": "Жив.(B): ", - "WarningTipTempString": "Жало t°: ", - "BadTipString": "ЖАЛО--", "SleepingSimpleString": "ZzZzz", "SleepingAdvancedString": "Очікування...", - "WarningSimpleString": "ГАРЯЧЕ!", - "WarningAdvancedString": "!!! ГАРЯЧЕ !!!\n!!! ЖАЛО !!!", "SleepingTipAdvancedString": "Жало:", - "IdleTipString": "Жало:", - "IdleSetString": " ->", - "TipDisconnectedString": "Жало вимкнено!", - "SolderingAdvancedPowerPrompt": "Живлення: ", - "OffString": "Вимк", - "YourGainMessage": "Приріст:" + "OffString": "Вимк" }, "messagesWarn": { "ResetOKMessage": "Скид. OK", @@ -38,9 +29,9 @@ "SettingLeftChar": "Л", "SettingAutoChar": "A", "SettingOffChar": "B", - "SettingSlowChar": "П", + "SettingSlowChar": "Н", "SettingMediumChar": "M", - "SettingFastChar": "Ш", + "SettingFastChar": "М", "SettingStartNoneChar": "В", "SettingStartSolderingChar": "П", "SettingStartSleepChar": "О", @@ -51,8 +42,7 @@ "SettingSensitivityHigh": "М", "SettingLockDisableChar": "В", "SettingLockBoostChar": "Т", - "SettingLockFullChar": "П", - "SettingNAChar": "Н/Д" + "SettingLockFullChar": "П" }, "menuGroups": { "PowerMenu": { @@ -208,6 +198,10 @@ "ColourInversion": { "text2": ["Інверт", "екрану"], "desc": "Налаштування контрасту/яскравості OLED екрану" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_VI.json b/Translations/translation_VI.json index 954c050e..0b4c530c 100644 --- a/Translations/translation_VI.json +++ b/Translations/translation_VI.json @@ -1,332 +1,207 @@ { - "languageCode": "VI", - "languageLocalName": "Tieng Viet", - "fonts": [ - "ascii_basic", - "latin_extended" - ], - "tempUnitFahrenheit": false, - "messages": { - "SettingsCalibrationWarning": "Chac chan mui hàn o nhiet đo phòng truoc khi tiep tuc!", - "SettingsResetWarning": "Ban chac chan muon khôi phuc tat ca cài đat ve mac đinh?", - "UVLOWarningString": "DC thap", - "UndervoltageString": "Đien áp thap", - "InputVoltageString": "Đau vào V: ", - "SleepingSimpleString": "Zzzz", - "SleepingAdvancedString": "Đang ngu...", - "SleepingTipAdvancedString": "Meo:", - "OffString": "Tat" - }, - "messagesWarn": { - "ResetOKMessage": "Reset OK", - "SettingsResetMessage": [ - "Mot so cài đat", - "đã thay đoi" - ], - "NoAccelerometerMessage": [ - "Không phát hien", - "gia toc ke!" - ], - "NoPowerDeliveryMessage": [ - "Không phát hien", - "USB-PD IC!" - ], - "LockingKeysString": "Đã khóa", - "UnlockingKeysString": "Mo khóa", - "WarningKeysLockedString": "Đã khóa!", - "WarningThermalRunaway": [ - "Nhiet", - "Tat gia nhiet" - ] - }, - "characters": { - "SettingRightChar": "R", - "SettingLeftChar": "L", - "SettingAutoChar": "A", - "SettingOffChar": "O", - "SettingSlowChar": "S", - "SettingMediumChar": "M", - "SettingFastChar": "F", - "SettingStartNoneChar": "O", - "SettingStartSolderingChar": "S", - "SettingStartSleepChar": "Z", - "SettingStartSleepOffChar": "R", - "SettingSensitivityOff": "O", - "SettingSensitivityLow": "L", - "SettingSensitivityMedium": "M", - "SettingSensitivityHigh": "H", - "SettingLockDisableChar": "D", - "SettingLockBoostChar": "B", - "SettingLockFullChar": "F" - }, - "menuGroups": { - "PowerMenu": { - "text2": [ - "Cài đat", - "nguon đien" - ], - "desc": "Cài đat nguon đien" - }, - "SolderingMenu": { - "text2": [ - "Cài đat", - "tay hàn" - ], - "desc": "Cài đat tay hàn" - }, - "PowerSavingMenu": { - "text2": [ - "Che đo", - "ngu" - ], - "desc": "Cài đat che đo tiet kiem đien" - }, - "UIMenu": { - "text2": [ - "Giao dien", - "nguoi dùng" - ], - "desc": "Cài đat giao dien nguoi dùng" - }, - "AdvancedMenu": { - "text2": [ - "Cài đat", - "nâng cao" - ], - "desc": "Cài đat nâng cao" - } - }, - "menuOptions": { - "DCInCutoff": { - "text2": [ - "Nguon", - "đien" - ], - "desc": "Nguon đien, đat đien áp giam. (DC 10V) (S 3.3V moi cell, tat gioi han công suat)" - }, - "SleepTemperature": { - "text2": [ - "Nhiet đo", - "khi ngu" - ], - "desc": "Giam nhiet đo khi o \"Che đo ngu\"" - }, - "SleepTimeout": { - "text2": [ - "Ngu", - "sau" - ], - "desc": "- thoi gian truoc khi \"Che đo ngu\" bat đau (S=giây | M=phút)" - }, - "ShutdownTimeout": { - "text2": [ - "Tat", - "sau" - ], - "desc": "- khoang thoi gian truoc khi tay hàn tat (M=phút)" - }, - "MotionSensitivity": { - "text2": [ - "Cam bien", - "cu đong" - ], - "desc": "- 0=tat | 1=đo nhay thap nhat| ... | 9=đo nhay cao nhat" - }, - "TemperatureUnit": { - "text2": [ - "Đon vi", - "nhiet đo" - ], - "desc": "C= Đo C | F= Đo F" - }, - "AdvancedIdle": { - "text2": [ - "Chi tiet", - "màn hình cho" - ], - "desc": "- hien thi thông tin chi tiet bang phông chu nho hon trên màn hình cho" - }, - "DisplayRotation": { - "text2": [ - "Huong", - "hien thi" - ], - "desc": "- R=huong tay phai | L=huong tay trái | A=tu đong" - }, - "BoostTemperature": { - "text2": [ - "Tăng", - "nhiet đo" - ], - "desc": "Nhiet đo dùng trong che đo \"tăng cuong\"" - }, - "AutoStart": { - "text2": [ - "Nhiet đo", - "đang tăng" - ], - "desc": "- O=tat | S=nhiet đo hàn | Z=cho o nhiet đo ngu đen khi cu đong | R=cho mà không gia nhiet đen khi cu đong" - }, - "CooldownBlink": { - "text2": [ - "Nguoi đi", - "chop mat" - ], - "desc": "-Nhap nháy nhiet đo sau khi viec gia nhiet tam dung trong khi mui hàn van nóng" - }, - "TemperatureCalibration": { - "text2": [ - "Hieu chuan", - "nhiet đo?" - ], - "desc": "-Bat đau hieu chuan bù nhiet cho mui hàn" - }, - "SettingsReset": { - "text2": [ - "Khôi phuc", - "cài đat goc?" - ], - "desc": "-đat lai tat ca cài đat ve mac đinh" - }, - "VoltageCalibration": { - "text2": [ - "Hieu chinh", - "đien áp đau vào?" - ], - "desc": "-bat đau hieu chuan VIN (nhan và giu đe thoát)" - }, - "AdvancedSoldering": { - "text2": [ - "Chi tiet", - "màn hình hàn" - ], - "desc": "-Hien thi thông tin bang phông chu nho hon trên màn hình hàn" - }, - "ScrollingSpeed": { - "text2": [ - "Toc đo", - "cuon" - ], - "desc": "Toc đo cuon văn ban(S=cham | F=nhanh)" - }, - "QCMaxVoltage": { - "text2": [ - "QC", - "Voltage" - ], - "desc": "Đien áp QC toi đa mà tay hàn yêu cau" - }, - "PDNegTimeout": { - "text2": [ - "PD", - "sau" - ], - "desc": "Thoi gian cho đàm phán PD trong các buoc 100ms đe tuong thích voi mot so bo sac QC" - }, - "PowerLimit": { - "text2": [ - "Công suat", - "gioi han" - ], - "desc": "-Công suat toi đa mà tay hàn có the su dung (W=watt)" - }, - "ReverseButtonTempChange": { - "text2": [ - "Đao nguoc", - "nút + -" - ], - "desc": "Đao nguoc chuc năng các nút đieu chinh nhiet đo" - }, - "TempChangeShortStep": { - "text2": [ - "Thay đoi n.đo", - "an nút nhanh" - ], - "desc": "Biên đo tăng/giam nhiet đo khi an nút nhanh" - }, - "TempChangeLongStep": { - "text2": [ - "Thay đoi n.đo", - "an nút lâu" - ], - "desc": "Biên đo tăng/giam nhiet đo khi an nút lâu" - }, - "PowerPulsePower": { - "text2": [ - "Công suat", - "kích nguon" - ], - "desc": "-Cuong đo công suat kích nguon (watt)" - }, - "HallEffSensitivity": { - "text2": [ - "Hall", - "đo nhay" - ], - "desc": "Đo nhay cam bien Hall đe phát hien che đo ngu (0=tat | 1=ít nhay nhat |...| 9=nhay nhat)" - }, - "LockingMode": { - "text2": [ - "Cho phép khóa", - "các nút" - ], - "desc": "Trong khi hàn, giu ca 2 nút đe khóa(D=tat | B=chi che đo tăng cuong | F=khóa hoàn toàn)" - }, - "MinVolCell": { - "text2": [ - "Voltage", - "toi thieu" - ], - "desc": "Đien áp toi thieu cho phép trên moi cell (3S: 3 - 3,7V | 4-6S: 2,4 - 3,7V)" - }, - "AnimLoop": { - "text2": [ - "Hoat anh", - "lap lai" - ], - "desc": "Lap lai các hoat anh trong màn hình chính" - }, - "AnimSpeed": { - "text2": [ - "Toc đo", - "hoat anh" - ], - "desc": "-Toc đo cua hoat anh menu (O=tat | S=cham | M=trung bình | F=nhanh)" - }, - "PowerPulseWait": { - "text2": [ - "Trì hoãn", - "đien áp kích" - ], - "desc": "Trì hoãn truoc khi kích hoat kích nguon(x 2,5 giây)" - }, - "PowerPulseDuration": { - "text2": [ - "Thoi luong", - "kích nguon" - ], - "desc": "-thoi luong kích nguon (x 250ms)" - }, - "LanguageSwitch": { - "text2": [ - "Ngôn ngu:", - "VI Tieng Viet" - ], - "desc": "-Ngôn ngu firmware hien tai" - }, - "Brightness": { - "text2": [ - "Đo tuong phan", - "màn hình" - ], - "desc": "-Đieu chinh đo sáng màn hình OLED" - }, - "ColourInversion": { - "text2": [ - "Đao nguoc màu", - "màn hình" - ], - "desc": "-Đao nguoc màu màn hình OLED" - } - } + "languageCode": "VI", + "languageLocalName": "Tieng Viet", + "fonts": ["ascii_basic", "latin_extended"], + "tempUnitFahrenheit": false, + "messages": { + "SettingsCalibrationWarning": "Chac chan mui hàn o nhiet đo phòng truoc khi tiep tuc!", + "SettingsResetWarning": "Ban chac chan muon khôi phuc tat ca cài đat ve mac đinh?", + "UVLOWarningString": "DC thap", + "UndervoltageString": "Đien áp thap", + "InputVoltageString": "Đau vào V: ", + "SleepingSimpleString": "Zzzz", + "SleepingAdvancedString": "Đang ngu...", + "SleepingTipAdvancedString": "Meo:", + "OffString": "Tat" + }, + "messagesWarn": { + "ResetOKMessage": "Reset OK", + "SettingsResetMessage": ["Mot so cài đat", "đã thay đoi"], + "NoAccelerometerMessage": ["Không phát hien", "gia toc ke!"], + "NoPowerDeliveryMessage": ["Không phát hien", "USB-PD IC!"], + "LockingKeysString": "Đã khóa", + "UnlockingKeysString": "Mo khóa", + "WarningKeysLockedString": "Đã khóa!", + "WarningThermalRunaway": ["Nhiet", "Tat gia nhiet"] + }, + "characters": { + "SettingRightChar": "R", + "SettingLeftChar": "L", + "SettingAutoChar": "A", + "SettingOffChar": "O", + "SettingSlowChar": "S", + "SettingMediumChar": "M", + "SettingFastChar": "F", + "SettingStartNoneChar": "O", + "SettingStartSolderingChar": "S", + "SettingStartSleepChar": "Z", + "SettingStartSleepOffChar": "R", + "SettingSensitivityOff": "O", + "SettingSensitivityLow": "L", + "SettingSensitivityMedium": "M", + "SettingSensitivityHigh": "H", + "SettingLockDisableChar": "D", + "SettingLockBoostChar": "B", + "SettingLockFullChar": "F" + }, + "menuGroups": { + "PowerMenu": { + "text2": ["Cài đat", "nguon đien"], + "desc": "Cài đat nguon đien" + }, + "SolderingMenu": { + "text2": ["Cài đat", "tay hàn"], + "desc": "Cài đat tay hàn" + }, + "PowerSavingMenu": { + "text2": ["Che đo", "ngu"], + "desc": "Cài đat che đo tiet kiem đien" + }, + "UIMenu": { + "text2": ["Giao dien", "nguoi dùng"], + "desc": "Cài đat giao dien nguoi dùng" + }, + "AdvancedMenu": { + "text2": ["Cài đat", "nâng cao"], + "desc": "Cài đat nâng cao" + } + }, + "menuOptions": { + "DCInCutoff": { + "text2": ["Nguon", "đien"], + "desc": "Nguon đien, đat đien áp giam. (DC 10V) (S 3.3V moi cell, tat gioi han công suat)" + }, + "SleepTemperature": { + "text2": ["Nhiet đo", "khi ngu"], + "desc": "Giam nhiet đo khi o \"Che đo ngu\"" + }, + "SleepTimeout": { + "text2": ["Ngu", "sau"], + "desc": "- thoi gian truoc khi \"Che đo ngu\" bat đau (S=giây | M=phút)" + }, + "ShutdownTimeout": { + "text2": ["Tat", "sau"], + "desc": "- khoang thoi gian truoc khi tay hàn tat (M=phút)" + }, + "MotionSensitivity": { + "text2": ["Cam bien", "cu đong"], + "desc": "- 0=tat | 1=đo nhay thap nhat| ... | 9=đo nhay cao nhat" + }, + "TemperatureUnit": { + "text2": ["Đon vi", "nhiet đo"], + "desc": "C= Đo C | F= Đo F" + }, + "AdvancedIdle": { + "text2": ["Chi tiet", "màn hình cho"], + "desc": "- hien thi thông tin chi tiet bang phông chu nho hon trên màn hình cho" + }, + "DisplayRotation": { + "text2": ["Huong", "hien thi"], + "desc": "- R=huong tay phai | L=huong tay trái | A=tu đong" + }, + "BoostTemperature": { + "text2": ["Tăng", "nhiet đo"], + "desc": "Nhiet đo dùng trong che đo \"tăng cuong\"" + }, + "AutoStart": { + "text2": ["Nhiet đo", "đang tăng"], + "desc": "- O=tat | S=nhiet đo hàn | Z=cho o nhiet đo ngu đen khi cu đong | R=cho mà không gia nhiet đen khi cu đong" + }, + "CooldownBlink": { + "text2": ["Nguoi đi", "chop mat"], + "desc": "-Nhap nháy nhiet đo sau khi viec gia nhiet tam dung trong khi mui hàn van nóng" + }, + "TemperatureCalibration": { + "text2": ["Hieu chuan", "nhiet đo?"], + "desc": "-Bat đau hieu chuan bù nhiet cho mui hàn" + }, + "SettingsReset": { + "text2": ["Khôi phuc", "cài đat goc?"], + "desc": "-đat lai tat ca cài đat ve mac đinh" + }, + "VoltageCalibration": { + "text2": ["Hieu chinh", "đien áp đau vào?"], + "desc": "-bat đau hieu chuan VIN (nhan và giu đe thoát)" + }, + "AdvancedSoldering": { + "text2": ["Chi tiet", "màn hình hàn"], + "desc": "-Hien thi thông tin bang phông chu nho hon trên màn hình hàn" + }, + "ScrollingSpeed": { + "text2": ["Toc đo", "cuon"], + "desc": "Toc đo cuon văn ban(S=cham | F=nhanh)" + }, + "QCMaxVoltage": { + "text2": ["QC", "Voltage"], + "desc": "Đien áp QC toi đa mà tay hàn yêu cau" + }, + "PDNegTimeout": { + "text2": ["PD", "sau"], + "desc": "Thoi gian cho đàm phán PD trong các buoc 100ms đe tuong thích voi mot so bo sac QC" + }, + "PowerLimit": { + "text2": ["Công suat", "gioi han"], + "desc": "-Công suat toi đa mà tay hàn có the su dung (W=watt)" + }, + "ReverseButtonTempChange": { + "text2": ["Đao nguoc", "nút + -"], + "desc": "Đao nguoc chuc năng các nút đieu chinh nhiet đo" + }, + "TempChangeShortStep": { + "text2": ["Thay đoi n.đo", "an nút nhanh"], + "desc": "Biên đo tăng/giam nhiet đo khi an nút nhanh" + }, + "TempChangeLongStep": { + "text2": ["Thay đoi n.đo", "an nút lâu"], + "desc": "Biên đo tăng/giam nhiet đo khi an nút lâu" + }, + "PowerPulsePower": { + "text2": ["Công suat", "kích nguon"], + "desc": "-Cuong đo công suat kích nguon (watt)" + }, + "HallEffSensitivity": { + "text2": ["Hall", "đo nhay"], + "desc": "Đo nhay cam bien Hall đe phát hien che đo ngu (0=tat | 1=ít nhay nhat |...| 9=nhay nhat)" + }, + "LockingMode": { + "text2": ["Cho phép khóa", "các nút"], + "desc": "Trong khi hàn, giu ca 2 nút đe khóa(D=tat | B=chi che đo tăng cuong | F=khóa hoàn toàn)" + }, + "MinVolCell": { + "text2": ["Voltage", "toi thieu"], + "desc": "Đien áp toi thieu cho phép trên moi cell (3S: 3 - 3,7V | 4-6S: 2,4 - 3,7V)" + }, + "AnimLoop": { + "text2": ["Hoat anh", "lap lai"], + "desc": "Lap lai các hoat anh trong màn hình chính" + }, + "AnimSpeed": { + "text2": ["Toc đo", "hoat anh"], + "desc": "-Toc đo cua hoat anh menu (O=tat | S=cham | M=trung bình | F=nhanh)" + }, + "PowerPulseWait": { + "text2": ["Trì hoãn", "đien áp kích"], + "desc": "Trì hoãn truoc khi kích hoat kích nguon(x 2,5 giây)" + }, + "PowerPulseDuration": { + "text2": ["Thoi luong", "kích nguon"], + "desc": "-thoi luong kích nguon (x 250ms)" + }, + "LanguageSwitch": { + "text2": ["Ngôn ngu:", "VI Tieng Viet"], + "desc": "-Ngôn ngu firmware hien tai" + }, + "Brightness": { + "text2": ["Đo tuong phan", "màn hình"], + "desc": "-Đieu chinh đo sáng màn hình OLED" + }, + "ColourInversion": { + "text2": ["Đao nguoc màu", "màn hình"], + "desc": "-Đao nguoc màu màn hình OLED" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" + } + } } diff --git a/Translations/translation_YUE_HK.json b/Translations/translation_YUE_HK.json index 97de4a62..faee8327 100644 --- a/Translations/translation_YUE_HK.json +++ b/Translations/translation_YUE_HK.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Sleeping...", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "NO TIP", - "SolderingAdvancedPowerPrompt": "Power: ", "OffString": "關" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "高", "SettingLockDisableChar": "無", "SettingLockBoostChar": "增", - "SettingLockFullChar": "全", - "SettingNAChar": "不適用" + "SettingLockFullChar": "全" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": "熒幕反轉色", "desc": "反轉OLED熒幕嘅黑白色" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_ZH_CN.json b/Translations/translation_ZH_CN.json index 14a898f5..3d4edc2c 100644 --- a/Translations/translation_ZH_CN.json +++ b/Translations/translation_ZH_CN.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Zzzz...", "SleepingTipAdvancedString": "--->", - "IdleTipString": "--->", - "IdleSetString": " /", - "TipDisconnectedString": "<-X-", - "SolderingAdvancedPowerPrompt": "Power: ", "OffString": "关" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "高", "SettingLockDisableChar": "无", "SettingLockBoostChar": "增", - "SettingLockFullChar": "全", - "SettingNAChar": "不适用" + "SettingLockFullChar": "全" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": "反转屏幕颜色", "desc": "反转OLED黑/白屏幕" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translation_ZH_TW.json b/Translations/translation_ZH_TW.json index b7d9da77..167d89df 100644 --- a/Translations/translation_ZH_TW.json +++ b/Translations/translation_ZH_TW.json @@ -12,10 +12,6 @@ "SleepingSimpleString": "Zzzz", "SleepingAdvancedString": "Sleeping...", "SleepingTipAdvancedString": "Tip:", - "IdleTipString": "Tip:", - "IdleSetString": " Set:", - "TipDisconnectedString": "NO TIP", - "SolderingAdvancedPowerPrompt": "Power: ", "OffString": "關" }, "messagesWarn": { @@ -46,8 +42,7 @@ "SettingSensitivityHigh": "高", "SettingLockDisableChar": "無", "SettingLockBoostChar": "增", - "SettingLockFullChar": "全", - "SettingNAChar": "不適用" + "SettingLockFullChar": "全" }, "menuGroups": { "PowerMenu": { @@ -203,6 +198,10 @@ "ColourInversion": { "text2": "螢幕反轉色", "desc": "反轉OLED螢幕的黑白色彩" + }, + "LOGOTime": { + "text2": ["Boot logo", "duration"], + "desc": "Sets the duration for the boot logo (S=seconds)" } } } diff --git a/Translations/translations_def.js b/Translations/translations_def.js index 78aaf327..5cb39e8e 100644 --- a/Translations/translations_def.js +++ b/Translations/translations_def.js @@ -16,7 +16,7 @@ var def = }, { "id": "UndervoltageString", - "maxLen": 16, + "maxLen": 15, "description": "Warning text shown when the unit turns off due to undervoltage in advanced mode." }, { @@ -33,7 +33,7 @@ var def = }, { "id": "SleepingAdvancedString", - "maxLen": 16, + "maxLen": 15, "description": "The text shown to indicate the unit is in sleep mode when the advanced view is turned on." }, { @@ -285,20 +285,20 @@ var def = { "id": "TemperatureCalibration", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "Used to calibrate the ADC+Op-amp offsets for the tip. This calibration must be performed when the tip temperature and the handle temperature are equal. Generally not required unless your device is reading more than 5°C off target." }, { "id": "SettingsReset", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "Resets all settings and calibrations to factory defaults. Does NOT erase custom user boot up logo's." }, { "id": "VoltageCalibration", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "Enters an adjustment mode where you can gradually adjust the measured voltage to compensate for any unit-to-unit variance in the voltage sense resistors." }, { @@ -317,13 +317,13 @@ var def = { "id": "QCMaxVoltage", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "This adjusts the maximum voltage the QC negotiation will adjust to. Does NOT affect USB-PD. Should be set safely based on the current rating of your power supply." }, { "id": "PDNegTimeout", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "How long until firmware stops trying to negotiate for USB-PD and tries QC instead. Longer times may help dodgy / old PD adapters, faster times move onto PD quickly. Units of 100ms. Recommended to keep small values." }, @@ -338,27 +338,27 @@ var def = { "id": "ReverseButtonTempChange", "maxLen": 6, - "maxLen2": 16, + "maxLen2": 15, "description": "Swaps which button increments and decrements on temperature change screens." }, { "id": "TempChangeShortStep", "maxLen": 8, - "maxLen2": 16, + "maxLen2": 15, "description": "Factor by which the temperature is changed with a quick press of the buttons." }, { "id": "TempChangeLongStep", "maxLen": 6, - "maxLen2": 16, + "maxLen2": 15, "description": "Factor by which the temperature is changed with a hold of the buttons." }, { "id": "PowerPulsePower", "maxLen": 6, - "maxLen2": 16, + "maxLen2": 15, "description": "Enables and sets the wattage of the power pulse. Power pulse causes the device to briefly turn on the heater to draw power to avoid power banks going to sleep." }, @@ -422,6 +422,12 @@ var def = "maxLen": 7, "maxLen2": 15, "description": "Inverts the entire OLED." + }, + { + "id": "LOGOTime", + "maxLen": 7, + "maxLen2": 15, + "description": "Sets the duration for the boot logo (S=seconds)." } ] } diff --git a/source/Core/BSP/Miniware/Vendor/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c b/source/Core/BSP/Miniware/Vendor/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c index 1990dcc5..18e2fc37 100644 --- a/source/Core/BSP/Miniware/Vendor/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c +++ b/source/Core/BSP/Miniware/Vendor/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c @@ -1321,10 +1321,10 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { - /* Enable the main output */ - __HAL_TIM_MOE_ENABLE(htim); - } + // if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { + // /* Enable the main output */ + // __HAL_TIM_MOE_ENABLE(htim); + // } /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) { @@ -3450,39 +3450,6 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef *htim) { htim->PeriodElapsedCallback(htim); #else HAL_TIM_PeriodElapsedCallback(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ - } - } - /* TIM Break input event */ - if (__HAL_TIM_GET_FLAG(htim, TIM_FLAG_BREAK) != RESET) { - if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_BREAK) != RESET) { - __HAL_TIM_CLEAR_IT(htim, TIM_IT_BREAK); -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - htim->BreakCallback(htim); -#else - HAL_TIMEx_BreakCallback(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ - } - } - /* TIM Trigger detection event */ - if (__HAL_TIM_GET_FLAG(htim, TIM_FLAG_TRIGGER) != RESET) { - if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_TRIGGER) != RESET) { - __HAL_TIM_CLEAR_IT(htim, TIM_IT_TRIGGER); -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - htim->TriggerCallback(htim); -#else - HAL_TIM_TriggerCallback(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ - } - } - /* TIM commutation event */ - if (__HAL_TIM_GET_FLAG(htim, TIM_FLAG_COM) != RESET) { - if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_COM) != RESET) { - __HAL_TIM_CLEAR_IT(htim, TIM_FLAG_COM); -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - htim->CommutationCallback(htim); -#else - HAL_TIMEx_CommutCallback(htim); #endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } } diff --git a/source/Core/Drivers/BootLogo.cpp b/source/Core/Drivers/BootLogo.cpp index 276311f1..37b38eba 100644 --- a/source/Core/Drivers/BootLogo.cpp +++ b/source/Core/Drivers/BootLogo.cpp @@ -20,11 +20,14 @@ void BootLogo::showOldFormat(const uint8_t *ptrLogoArea) { OLED::drawAreaSwapped(0, 0, 96, 16, (uint8_t *)(ptrLogoArea + 4)); OLED::refresh(); - // Delay here until button is pressed or its been 4 seconds - waitForButtonPressOrTimeout(TICKS_SECOND * 4); + // Delay here until button is pressed or its been the amount of seconds set by the user + waitForButtonPressOrTimeout(TICKS_SECOND * getSettingValue(SettingsOptions::LOGOTime)); } void BootLogo::showNewFormat(const uint8_t *ptrLogoArea) { + if (getSettingValue(SettingsOptions::LOGOTime) == 0) { + return; + } // New logo format (a) fixes long standing byte swap quirk and (b) supports animation uint8_t interFrameDelay = ptrLogoArea[0]; OLED::clearScreen(); @@ -39,24 +42,16 @@ void BootLogo::showNewFormat(const uint8_t *ptrLogoArea) { position += len; buttons = getButtonState(); - // Button pressed - if (buttons != BUTTON_NONE) { - return; - } - if (interFrameDelay) { osDelay(interFrameDelay * 5); - } else { - // Delay here until button is pressed or its been 4 seconds - waitForButtonPressOrTimeout(TICKS_SECOND * 4); + } + // 1024 less the header type byte and the inter-frame-delay + if (getSettingValue(SettingsOptions::LOGOTime) < 5 && (position == 1022 || len == 0)) { + // Delay here until button is pressed or its been the amount of seconds set by the user + waitForButtonPressOrTimeout(TICKS_SECOND * getSettingValue(SettingsOptions::LOGOTime)); return; } - // If this was an early exit; bail now - if (len == 0) { - return; - } - - } while (position < 1022); // 1024 less the header type byte and the inter-frame-delay + } while (buttons == BUTTON_NONE); } int BootLogo::showNewFrame(const uint8_t *ptrLogoArea) { uint8_t length = ptrLogoArea[0]; @@ -81,4 +76,4 @@ int BootLogo::showNewFrame(const uint8_t *ptrLogoArea) { OLED::refresh(); return (length * 2) + 1; -} \ No newline at end of file +} diff --git a/source/Core/Drivers/Font.h b/source/Core/Drivers/Font.h index 16ed3529..7c9cc247 100644 --- a/source/Core/Drivers/Font.h +++ b/source/Core/Drivers/Font.h @@ -190,6 +190,12 @@ const uint8_t invertDisplayIcon[] = { 0xFE, 0x01, 0x79, 0x25, 0x79, 0x01, 0xFE, 0x00, 0x20, 0x20, 0x20, 0x20, 0xDF, 0x07, 0x8F, 0xDF, 0xFF, 0x01, 0xFE, 0x86, 0xDA, 0x86, 0xFE, 0x01, 0x7F, 0x80, 0xA4, 0xBE, 0xA0, 0x80, 0x7F, 0x00, 0x04, 0x0E, 0x1F, 0x04, 0xFB, 0xFB, 0xFB, 0xFB, 0xFF, 0x80, 0x7F, 0x5B, 0x41, 0x5F, 0x7F, 0x80}; +const uint8_t infinityIcon[] = { + // width = 24 + // height = 16 + 0x00, 0xc0, 0x70, 0x18, 0x0c, 0x0c, 0x0c, 0x0c, 0x18, 0x10, 0x20, 0x80, 0xc0, 0x60, 0x30, 0x18, 0x0c, 0x0c, 0x0c, 0x0c, 0x18, 0x70, 0xc0, 0x00, + 0x00, 0x01, 0x07, 0x0c, 0x18, 0x18, 0x18, 0x18, 0x0c, 0x06, 0x03, 0x01, 0x00, 0x02, 0x04, 0x0c, 0x18, 0x18, 0x18, 0x18, 0x0c, 0x07, 0x01, 0x00}; + /* * 16x16 icons * 32 * 3 = Frame size * Frame count diff --git a/source/Core/Inc/Settings.h b/source/Core/Inc/Settings.h index cf30ced4..9fdb7e24 100644 --- a/source/Core/Inc/Settings.h +++ b/source/Core/Inc/Settings.h @@ -49,9 +49,10 @@ enum SettingsOptions { PDNegTimeout = 32, // PD timeout in 100ms steps OLEDInversion = 33, // Invert the colours on the display OLEDBrightness = 34, // Brightness for the OLED display + LOGOTime = 35, // Duration the logo will be displayed for // - SettingsOptionsLength = 35, // + SettingsOptionsLength = 36, // }; typedef enum { diff --git a/source/Core/Inc/Translation.h b/source/Core/Inc/Translation.h index 0bfca9f4..58c99ca7 100644 --- a/source/Core/Inc/Translation.h +++ b/source/Core/Inc/Translation.h @@ -63,6 +63,7 @@ enum class SettingsItemIndex : uint8_t { LanguageSwitch, Brightness, ColourInversion, + LOGOTime, NUM_ITEMS, }; diff --git a/source/Core/Src/Settings.cpp b/source/Core/Src/Settings.cpp index fd11279e..d8974989 100644 --- a/source/Core/Src/Settings.cpp +++ b/source/Core/Src/Settings.cpp @@ -84,6 +84,7 @@ static const SettingConstants settingsConstants[(int)SettingsOptions::SettingsOp {0, 50, 1, 20}, // PDNegTimeout {0, 1, 1, 0}, // OLEDInversion {0, 99, 11, 33}, // OLEDBrightness + {0, 5, 1, 1}, // LOGOTime }; static_assert((sizeof(settingsConstants) / sizeof(SettingConstants)) == ((int)SettingsOptions::SettingsOptionsLength)); diff --git a/source/Core/Src/gui.cpp b/source/Core/Src/gui.cpp index 3ff16038..31ae0c88 100644 --- a/source/Core/Src/gui.cpp +++ b/source/Core/Src/gui.cpp @@ -69,6 +69,7 @@ static bool settings_showPowerPulseOptions(void); static void settings_displayPowerPulseDuration(void); static void settings_displayBrightnessLevel(void); static void settings_displayInvertColor(void); +static void settings_displayLogoTime(void); #ifdef HALL_SENSOR static void settings_displayHallEffect(void); @@ -223,6 +224,7 @@ const menuitem UIMenu[] = { * -Animation Loop * OLED Brightnes * Invert Screen + * Logo Timeout * Detailed IDLE * Detailed Soldering */ @@ -239,6 +241,7 @@ const menuitem UIMenu[] = { {SETTINGS_DESC(SettingsItemIndex::AnimLoop), nullptr, settings_displayAnimationLoop, settings_displayAnimationOptions, SettingsOptions::AnimationLoop}, /*Animation Loop switch */ {SETTINGS_DESC(SettingsItemIndex::Brightness), nullptr, settings_displayBrightnessLevel, nullptr, SettingsOptions::OLEDBrightness}, /*Brightness Level*/ {SETTINGS_DESC(SettingsItemIndex::ColourInversion), nullptr, settings_displayInvertColor, nullptr, SettingsOptions::OLEDInversion}, /*Invert screen colour*/ + {SETTINGS_DESC(SettingsItemIndex::LOGOTime), nullptr, settings_displayLogoTime, nullptr, SettingsOptions::LOGOTime}, /*Set logo duration*/ {SETTINGS_DESC(SettingsItemIndex::AdvancedIdle), nullptr, settings_displayAdvancedIDLEScreens, nullptr, SettingsOptions::DetailedIDLE}, /*Advanced idle screen*/ {SETTINGS_DESC(SettingsItemIndex::AdvancedSoldering), nullptr, settings_displayAdvancedSolderingScreens, nullptr, SettingsOptions::DetailedSoldering}, /*Advanced soldering screen*/ {0, nullptr, nullptr, nullptr, SettingsOptions::SettingsOptionsLength} // end of menu marker. DO NOT REMOVE @@ -326,8 +329,8 @@ static void settings_displayInputVRange(void) { static bool settings_showInputVOptions(void) { return getSettingValue(SettingsOptions::MinDCVoltageCells) > 0; } static void settings_displayInputMinVRange(void) { - printShortDescription(SettingsItemIndex::MinVolCell, 4); - OLED::printNumber(getSettingValue(SettingsOptions::MinVoltageCells) / 10, 2, FontStyle::LARGE); + printShortDescription(SettingsItemIndex::MinVolCell, 5); + OLED::printNumber(getSettingValue(SettingsOptions::MinVoltageCells) / 10, 1, FontStyle::LARGE); OLED::print(SymbolDot, FontStyle::LARGE); OLED::printNumber(getSettingValue(SettingsOptions::MinVoltageCells) % 10, 1, FontStyle::LARGE); } @@ -449,7 +452,6 @@ static bool settings_setTempF(void) { static void settings_displayTempF(void) { printShortDescription(SettingsItemIndex::TemperatureUnit, 7); - OLED::print((getSettingValue(SettingsOptions::TemperatureInF)) ? SymbolDegF : SymbolDegC, FontStyle::LARGE); } @@ -460,7 +462,6 @@ static void settings_displayAdvancedSolderingScreens(void) { static void settings_displayAdvancedIDLEScreens(void) { printShortDescription(SettingsItemIndex::AdvancedIdle, 7); - OLED::drawCheckbox(getSettingValue(SettingsOptions::DetailedIDLE)); } @@ -755,9 +756,9 @@ static void settings_displayPowerPulseDuration(void) { static void settings_displayBrightnessLevel(void) { OLED::drawArea(0, 0, 16, 16, brightnessIcon); - OLED::setCursor(5 * FONT_12_WIDTH - 2, 0); + OLED::setCursor(6 * FONT_12_WIDTH - 2, 0); // printShortDescription(SettingsItemIndex::Brightness, 7); - OLED::printNumber((getSettingValue(SettingsOptions::OLEDBrightness) / 11 + 1), 3, FontStyle::LARGE); + OLED::printNumber((getSettingValue(SettingsOptions::OLEDBrightness) / 11 + 1), 2, FontStyle::LARGE); // While not optimal to apply this here, it is _very_ convienient OLED::setBrightness(getSettingValue(SettingsOptions::OLEDBrightness)); } @@ -766,12 +767,23 @@ static void settings_displayInvertColor(void) { OLED::drawArea(0, 0, 24, 16, invertDisplayIcon); OLED::setCursor(7 * FONT_12_WIDTH - 2, 0); // printShortDescription(SettingsItemIndex::ColourInversion, 7); - OLED::drawCheckbox(getSettingValue(SettingsOptions::OLEDInversion)); // While not optimal to apply this here, it is _very_ convienient OLED::setInverseDisplay(getSettingValue(SettingsOptions::OLEDInversion)); } +static void settings_displayLogoTime(void) { + printShortDescription(SettingsItemIndex::LOGOTime, 5); + if (getSettingValue(SettingsOptions::LOGOTime) == 0) { + OLED::print(translatedString(Tr->OffString), FontStyle::LARGE); + } else if (getSettingValue(SettingsOptions::LOGOTime) == 5) { + OLED::drawArea(OLED_WIDTH - 24 - 2, 0, 24, 16, infinityIcon); + } else { + OLED::printNumber(getSettingValue(SettingsOptions::LOGOTime), 2, FontStyle::LARGE); + OLED::print(SymbolSeconds, FontStyle::LARGE); + } +} + #ifdef HALL_SENSOR static void settings_displayHallEffect(void) { printShortDescription(SettingsItemIndex::HallEffSensitivity, 7);