diff --git a/workspace/ts100/src/Strings.c b/workspace/ts100/src/Strings.c
index cbd6e8dc..55dcca12 100644
--- a/workspace/ts100/src/Strings.c
+++ b/workspace/ts100/src/Strings.c
@@ -7,143 +7,179 @@
 #include "Strings.h"
 #define LANG_EN
 #ifdef LANG_EN
-const char* SettingsLongNames[14] =
-		{
-		/*These are all the help text for all the settings.*/
-		/*All must start with 6 spaces so they come on screen nicely.*/
-		"      Power source. Sets cutoff voltage. <DC 10V> <S 3.3V per cell>",
-				"      Sleep Temperature <C>", "      Sleep Timeout <Minutes>",
-				"      Shutdown Timeout <Minutes>",
-				"      Motion Sensitivity <0.Off 1.least sensitive 9.most sensitive>",
-				"      Temperature Unit", "      Temperature Rounding Amount",
-				"      Temperature Display Update Rate",
-				"      Display Orientation <A. Automatic L. Left Handed R. Right Handed>",
-				"      Enable front key enters boost mode 450C mode when soldering",
-				"      Temperature when in \"boost\" mode",
-				"      Changes the arrows to a power display when soldering",
-				"      Automatically starts the iron into soldering on power up. T=Soldering, S= Sleep mode,F=Off",
-				"      Blink the temperature on the cooling screen while the tip is still hot." };
-
-const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fail" }; //All fixed 8 chars
-const char* UVLOWarningString = "Low Volt"; //Fixed width 8 chars
-const char* CoolingPromptString = "Off  "; //Fixed width 5 chars
-const char SettingTrueChar = 'T';
-const char SettingFalseChar = 'F';
-const char SettingSleepChar = 'S';
-const char SettingFastChar = 'F';
-const char SettingMediumChar = 'M';
-const char SettingSlowChar = 'S';
-const char SettingRightChar = 'R';
-const char SettingLeftChar = 'L';
-const char SettingAutoChar = 'A';
-const char SettingTempCChar = 'C';
-const char SettingTempFChar = 'F';
-
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Power source. Sets cutoff voltage. <DC=10V S=3.3V per cell>",
+    "      Sleep Temperature <C>",
+    "      Sleep Timeout <Minutes>",
+    "      Shutdown Timeout <Minutes>",
+    "      Motion Sensitivity <0=Off 1=Least sensitive 9=Most sensitive>",
+    "      Temperature Unit <C=Celsius F=Farnheit>",
+    "      Temperature Rounding Amount <Units>",
+    "      Temperature Display Update Rate <S=Slow M=Medium F=Fast>",
+    "      Display Orientation <A=Automatic L=Left Handed R=Right Handed>",
+    "      Enable front key enters boost mode 450C mode when soldering <T=True F=False>",
+    "      Temperature when in \"boost\" mode <C>",
+    "      Changes the arrows to a power display when soldering <T=True F=False>",
+    "      Automatically starts the iron into soldering on power up. <T=Soldering S=Sleep mode F=Off>",
+    "      Blink the temperature on the cooling screen while the tip is still hot. <T=True F=False>"
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fail" }; //All fixed 8 chars
+  const char* UVLOWarningString = "Low Volt"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Off  "; //Fixed width 5 chars
+  const char SettingTrueChar = 'T';
+  const char SettingFalseChar = 'F';
+  const char SettingSleepChar = 'S';
+  const char SettingFastChar = 'F';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'S';
+  const char SettingRightChar = 'R';
+  const char SettingLeftChar = 'L';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
 #endif
+
 #ifdef LANG_ES
-const char* SettingsLongNames[14] =
-{
-	/*These are all the help text for all the settings.*/
-	/*All must start with 6 spaces so they come on screen nicely.*/
-	"      Fuente de energía. Ajusta el límite inferior de voltaje. <DC 10V> <S 3.3V por celda>",
-	"      Temperatura en reposo. <C>",
-	"      Tiempo hasta activar reposo. <Minutos>",
-	"      Tiempo hasta apagado. <Minutos>",
-	"      Sensibilidad del movimiento. <0. Apagado, 1. El menos sensible, 9. El más sensible>",
-	"      Unidad de temperatura.",
-	"      Redondeo de la temperatura.",
-	"      Tasa de actualización de la temperatura.",
-	"      Orientación de la pantalla <A. Automático, I. Mano izquierda, D. Mano derecha>",
-	"      Activar el botón \"Boost\" en modo soldadura.",
-	"      Temperatura en modo \"Boost\".",
-	"      Cambiar las flechas en pantalla por indicador de potencia en modo soldadura.",
-	"      Iniciar modo soldadura en el encendido. <V. Sí, S. Modo reposo, F. No ",
-	"      Parpadea la temperatura en el enfriamiento si la punta sigue caliente."};
-
-const char* TempCalStatus[3] = {"CAL TEMP", "CAL OK  ", "CAL FAIL"}; //All fixed 8 chars
-const char* UVLOWarningString = "LOW VOLT";//Fixed width 8 chars
-const char* CoolingPromptString = "Cool ";//Fixed width 5 chars
-const char SettingTrueChar = 'V';
-const char SettingFalseChar = 'F';
-const char SettingSleepChar = 'S';
-const char SettingFastChar = 'R';
-const char SettingMediumChar = 'M';
-const char SettingSlowChar = 'L';
-const char SettingRightChar = 'D';
-const char SettingLeftChar = 'I';
-const char SettingAutoChar = 'A';
-const char SettingTempCChar = 'C';
-const char SettingTempFChar = 'F';
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Fuente de energía. Ajusta el límite inferior de voltaje. <DC=10V S=3.3V por celda>",
+    "      Temperatura en reposo. <C>",
+    "      Tiempo hasta activar reposo. <Minutos>",
+    "      Tiempo hasta apagado. <Minutos>",
+    "      Sensibilidad del movimiento. <0=Apagado 1=El menos sensible 9=El más sensible>",
+    "      Unidad de temperatura.",
+    "      Redondeo de la temperatura.",
+    "      Tasa de actualización de la temperatura.",
+    "      Orientación de la pantalla <A=Automático I=Mano izquierda D=Mano derecha>",
+    "      Activar el botón \"Boost\" en modo soldadura.",
+    "      Temperatura en modo \"Boost\". <C>",
+    "      Cambiar las flechas en pantalla por indicador de potencia en modo soldadura.",
+    "      Iniciar modo soldadura en el encendido. <V=Sí S=Modo reposo F=No>",
+    "      Parpadea la temperatura en el enfriamiento si la punta sigue caliente."
+  };
+  const char* TempCalStatus[3] = {"CAL TEMP", "CAL OK  ", "CAL FAIL"}; //All fixed 8 chars
+  const char* UVLOWarningString = "LOW VOLT"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Cool "; //Fixed width 5 chars
+  const char SettingTrueChar = 'V';
+  const char SettingFalseChar = 'F';
+  const char SettingSleepChar = 'S';
+  const char SettingFastChar = 'R';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'I';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
 #endif
+
 #ifdef LANG_DE
-const char* SettingsLongNames[14] =
-		{
-		/*These are all the help text for all the settings.*/
-		/*All must start with 6 spaces so they come on screen nicely.*/
-		"      Stromversorgung. Setzt Abschaltspannung <DC 10V> <S 3.3V pro Zelle>",
-				"      Ruhetemperatur <C>", "      Ruhemodus nach <Minuten>",
-				"      Abschaltzeit <Minuten>",
-				"      Bewegungsempfindlichkeit <0.Aus 1.Minimal 9.Maximal>",
-				"      Temperatur Einheit", "      Temperatur Runden",
-				"      Temperaturanzeige Updaterate",
-				"      Anzeigerichtung <A. Auto L. Linkshändig R. Rechtshändig>",
-				"      Fronttaste für Temperaturboost einschalten",
-				"      Temperatur im \"boost\"-Modus",
-				"      Ändert \"Temperaturpfeile\" in Leistungsbalken",
-				"      Automatischer Start beim Einschalten. J=Löttemp., R=Ruhemodus,N=Aus",
-				"      Temperatur blinkt beim Abkühlen, solange noch heiß." };
-
-const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fehl" }; //All fixed 8 chars
-const char* UVLOWarningString = "V gering"; //Fixed width 8 chars
-const char* CoolingPromptString = "Kalt "; //Fixed width 5 chars
-const char SettingTrueChar = 'J';
-const char SettingFalseChar = 'N';
-const char SettingSleepChar = 'R';
-const char SettingFastChar = 'S';
-const char SettingMediumChar = 'M';
-const char SettingSlowChar = 'L';
-const char SettingRightChar = 'R';
-const char SettingLeftChar = 'L';
-const char SettingAutoChar = 'A';
-const char SettingTempCChar = 'C';
-const char SettingTempFChar = 'F';
-
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Stromversorgung. Setzt Abschaltspannung <DC=10V S=3.3V pro Zelle>",
+    "      Ruhetemperatur <C>",
+    "      Ruhemodus nach <Minuten>",
+    "      Abschaltzeit <Minuten>",
+    "      Bewegungsempfindlichkeit <0=Aus 1=Minimal 9=Maximal>",
+    "      Temperatur Einheit",
+    "      Temperatur Runden",
+    "      Temperaturanzeige Updaterate",
+    "      Anzeigerichtung <A=Auto L=Linkshändig R=Rechtshändig>",
+    "      Fronttaste für Temperaturboost einschalten",
+    "      Temperatur im \"boost\"-Modus <C>",
+    "      Ändert \"Temperaturpfeile\" in Leistungsbalken",
+    "      Automatischer Start beim Einschalten. <J=Löttemp R=Ruhemodus N=Aus>",
+    "      Temperatur blinkt beim Abkühlen, solange noch heiß."
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fehl" }; //All fixed 8 chars
+  const char* UVLOWarningString = "V gering"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Kalt "; //Fixed width 5 chars
+  const char SettingTrueChar = 'J';
+  const char SettingFalseChar = 'N';
+  const char SettingSleepChar = 'R';
+  const char SettingFastChar = 'S';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'R';
+  const char SettingLeftChar = 'L';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
 #endif
+
 #ifdef LANG_FR
-const char* SettingsLongNames[14] =
-		{
-		/*These are all the help text for all the settings.*/
-		/*All must start with 6 spaces so they come on screen nicely.*/
-				"      Type d\'alimentation. Regle la tension de coupure. <DC 10V> <S 3.3V par cellules>",
-				"      Temperature en veille. <C>",
-				"      Temps avant mise en veille. <Minutes>",
-				"      Temps avant extinction. <Minutes>",
-				"      Sensibilitee du capteur de mouvement. <0.Inactif 1.peu sensible 9.tres sensible>",
-				"      Unitee de temperature.",
-				"      Arrondissement de la temperature.",
-				"      Taux de raffraichissement de la temperature.",
-				"      Orientation de l\'affichage. <A. Automatique G. Gaucher D. Droitier>",
-				"      Active le mode \"Boost\" 450C sur le bouton de devant pendant la soudure.",
-				"      Temperature du mode \"Boost\".",
-				"      Change les fleches en affichage de la tension pendant la soudure.",
-				"      Demarre automatiquement la soudure a l\'allumage. <A=Active, V= Mode Veille, D=Desactive>",
-				"      Fait clignotter la temperature pendant la phase de refroidissement quand la panne est chaude." };
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Type d\'alimentation. Regle la tension de coupure. <DC=10V S=3.3V par cellules>",
+    "      Temperature en veille. <C>",
+    "      Temps avant mise en veille. <Minutes>",
+    "      Temps avant extinction. <Minutes>",
+    "      Sensibilitee du capteur de mouvement. <0=Inactif 1=Peu sensible 9=Tres sensible>",
+    "      Unitee de temperature.",
+    "      Arrondissement de la temperature.",
+    "      Taux de raffraichissement de la temperature.",
+    "      Orientation de l\'affichage. <A=Automatique G=Gaucher D=Droitier>",
+    "      Active le mode \"Boost\" 450C sur le bouton de devant pendant la soudure.",
+    "      Temperature du mode \"Boost\". <C>",
+    "      Change les fleches en affichage de la tension pendant la soudure.",
+    "      Demarre automatiquement la soudure a l\'allumage. <A=Active, V=Mode Veille, D=Desactive>",
+    "      Fait clignotter la temperature pendant la phase de refroidissement quand la panne est chaude."
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Err " }; //All fixed 8 chars
+  const char* UVLOWarningString = "Batt Bas"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Etein"; //Fixed width 5 chars
+  const char SettingTrueChar = 'A';
+  const char SettingFalseChar = 'D';
+  const char SettingSleepChar = 'V';
+  const char SettingFastChar = 'R';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'G';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
 
-const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Err " }; //All fixed 8 chars
-const char* UVLOWarningString = "Batt Bas"; //Fixed width 8 chars
-const char* CoolingPromptString = "Etein"; //Fixed width 5 chars
-const char SettingTrueChar = 'A';
-const char SettingFalseChar = 'D';
-const char SettingSleepChar = 'V';
-const char SettingFastChar = 'R';
-const char SettingMediumChar = 'M';
-const char SettingSlowChar = 'L';
-const char SettingRightChar = 'D';
-const char SettingLeftChar = 'G';
-const char SettingAutoChar = 'A';
-const char SettingTempCChar = 'C';
-const char SettingTempFChar = 'F';
+#ifdef LANG_IT
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Sorgente di alimentazione. Imposta il limite inferiore di tensione. <DC=10V S=3.3V per cella>",
+    "      Temperatura modalità riposo <C>",
+    "      Timeout per passaggio a modalità riposo <Minuti>",
+    "      Timeout spegnimento <Minuti>",
+    "      Sensibilità al movimento <0=Spento 1=Sensibilità minima 9=Sensibilità massima>",
+    "      Unità di temperatura",
+    "      Arrotondamento temperatura",
+    "      Velocità di aggiornamento temperatura",
+    "      Orientamento del display <A=Automatico S=Sinistrorso D=Destrorso>",
+    "      Il tasto anteriore abilita modalità \"boost\" fino a 450C durante la saldatura",
+    "      Temperatura in modalità \"boost\" <C>",
+    "      Visualizza il grafico della potenza assorbita al posto delle frecce",
+    "      Avvia automaticamente il saldatore quando viene alimentato. <S=Modalità saldatura R=Modalità riposo N=Spento>",
+    "      Durante lo spegnimento la temperatura lampeggia sul display finché la punta è calda."
+  };
 
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Err " }; //All fixed 8 chars
+  const char* UVLOWarningString = "LOW VOLT"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Cool"; //Fixed width 5 chars
+  const char SettingTrueChar = 'S';
+  const char SettingFalseChar = 'N';
+  const char SettingSleepChar = 'R';
+  const char SettingFastChar = 'V';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'S';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
 #endif
 const char* SettingsShortNames[14] = { "PWRSC ", "STMP ", "STME ", "SHTME ",
 		"MSENSE ", "TMPUNT ", "TMPRND ", "TMPSPD ", "DSPROT ", "BOOST  ",