Stop adjust buttons auto-rotating

Closes #270

README.md

@@ -1,10 +1,12 @@
 # TS100
+
 This is a complete rewrite of the open source software for the ts100 soldering iron.
 The version two fork of this code has no shared code with the original firmware from Miniware (E-design) group.
+
 This project is considered feature complete for use as a soldering iron, *so please suggest any feature improvements you would like!*
 
-A short(ish) video that goes through every single menu option in the firmware is available [over here](https://www.youtube.com/watch?v=WlnpboYfxNk). 
-This video was created on an earlier 1.x version of the firmware, so alot has changed and a new video will be coming soon for the 2.x fork.
+A short(ish) video that goes through every single menu option in the firmware is available [over here](https://www.youtube.com/watch?v=WlnpboYfxNk).
+This video was created on an earlier 1.x version of the firmware, so alot has changed but should be fairly intuitive as the menu has vastly improved.
 
 *This firmware does **NOT** support the usb port while running for changing settings. This is done through the onscreen menu only. Logos are edited using the tool or python script and uploaded in DFU mode.*
 
@@ -12,6 +14,7 @@ This video was created on an earlier 1.x version of the firmware, so alot has ch
 Please calibrate your irons voltage reading when you are using a lithium battery after any firmware upgrades.*
 
 ## Features
+
 * PID iron temperature control
 * Automatic sleep with selectable sensitivity
 * Motion wake support
@@ -26,10 +29,11 @@ Please calibrate your irons voltage reading when you are using a lithium battery
 * Battery charge level indicatior if power source set to a lipo cell count.
 * Custom bootup logo support
 * Automatic LCD rotation based on orientation
+* Supports both the version 1 and version 2 hardware
 
 ## Upgrading your ts100 iron
 
-This is completely safe, if it goes wrong just put the .hex file from the official website onto the unit and your back to the old firmware. Downloads for the hex files to flash are available on the [releases page.](https://github.com/Ralim/ts100/releases) The file you want is called *ts100.hex* unless you want the translations, they are ts100_*language short name*.hex.
+This is completely safe, if it goes wrong just put the .hex file from the official website onto the unit and your back to the old firmware. Downloads for the hex files to flash are available on the [releases page.](https://github.com/Ralim/ts100/releases) The file you want is called *ts100_EN.hex* unless you want the translations, they are ts100_*language short name*.hex.
 
 Officially the bootloader on the iron only works under windows. However, users have reported that it does work under Mac, and can be made to work under Linux *sometimes*. Details over on the [wiki page](https://github.com/Ralim/ts100/wiki/Upgrading-Firmware).
 
@@ -55,13 +59,15 @@ There are further instructions on the [wiki](https://github.com/Ralim/ts100/wiki
 
 This new firmware uses a new menu system to allow access to the settings on the device.
 When on the main screen, the unit shows prompts for the two most common operations.
+
 * Pressing the button near the tip enters soldering mode
 * Pressing the button near the USB enters the settings menu.
 * Holding the button near the tip will enter soldering temperature adjust mode (This is the same as the one in the soldering menu, just to let you edit before heating up).
 * Holding the button near the USB end will show the firmware version details.
+
 ## Soldering mode
 
-In this mode the iron works as you would expect, pressing either button will take you to a temperature change screen. 
+In this mode the iron works as you would expect, pressing either button will take you to a temperature change screen.
 Use each button to go up and down in temperature. Pressing both buttons will exit you from the temperature menu (or wait 3 seconds and it will time out).
 Pressing both buttons or holding the button near the USB will exit the soldering mode.
 Holding the button at the front of the iron will enter boost mode (if enabled).
@@ -70,28 +76,17 @@ Holding the button at the front of the iron will enter boost mode (if enabled).
 
 This menu allows you to cycle through all the options and set their values.
 The button near the USB cycles through the options, and the one near the tip changes the selected option.
-Note that settings are not saved until you exit the menu, and some settings such as screen flip do not apply until a power cycle is applied.
-If you leave the unit alone (ie don't press any buttons) on a setting, after 3 seconds the screen will scroll a longer version of the name
+Note that settings are not saved until you exit the menu.
+If you leave the unit alone (ie don't press any buttons) on a setting, after 3 seconds the screen will scroll a rough description of the setting.
 
-* PWRSC -> Power source, select a cell count if using a LiPo, or DC to disable the shutdown. (Sets it to minimum of 10V).
-* STMP -> The temperature the unit drops to in sleep mode
-* SLTME -> Sleep time, how long it takes before the unit goes to sleep
-* SHTME -> Shutdown Time, how long the unit will wait after movement before shutting down completely
-* MSENSE -> Motion Sensitivity,0*9,0 means motion sensing is turned off, 9 is most sensitive, 1 is least sensitive (ie takes more movement to trigger)
-* ADVDSP -> Enable the advanced display (shows more details)
-* DSPROT -> Display rotation mode, Automatic, Left handed or Right handed
-* BOOST -> Enable boost mode
-* BTMP -> Set the temperature for the boost mode
-* ASART -> Automatically start the unit when power is applied (i.e. the unit will go straight into soldering mode)
-* CLBLNK -> Blink the screen as an alert when cooling down
-* TMP CAL -> Use to calibrate offset on the tip temperature
-* RESET -> Use to force a complete reset on exit of the settings menu
-* TMPUNIT -> Temperature unit, C or F
+The menu is arranged so that the most often used settings are first.
+With submenu's being selected to enter using the front button (as if you were going to change the setting).
+Scrolling through the submenu will return you back to its entry location after you scroll through all of the options.
 
 ### Calibrating input voltage
 
 Due to the tolerance on the resistors used for the input voltage divider, some irons can be up to 0.6V out on the voltage measurement.
-Please calibrate your iron if you have any issues with the cutoff voltage. 
+Please calibrate your iron if you have any issues with the cutoff voltage.
 Note that cutoff messages can also be triggered by using a power supply that is too weak and fails under the load of the iron.
 This is more critical than before with the new cell count based cutout voltage.
 
@@ -99,19 +94,11 @@ To calibrate your Iron:
 
 1. Measure the input voltage with a multimeter and note it down.
 2. Connect the input to your iron.
-3. On the home screen (showing iron symbol), press both buttons simultainiously.
-4. The iron will now show the tip temperature.
-5. Press the button near the soldering iron tip.
-6. The screen will display the measured input voltage.
-7. If this is the same as what you measured before skip to step 13
-8. Otherwise, press the button near the USB end of the iron
-9. The voltage will now slowly blink.
-10. Use the buttons to adjust the reading up and down until it reads as close as possible to the voltage you measured earlier.
-11. When it is reading as close as possible, press both buttons at once.
-12. The screen will go back to just showing the input voltage.
-13. Press the button near the tip of the iron to exit back to the live temperature display.
-14. Press both buttons at once to exit back to the idle screen.
-15. You're done. Enjoy your iron.
+3. Enter the settings menu
+4. Under the advanced submenu
+5. Select the calibrate voltage option
+6. Use the front and back buttons to adjust the displayed voltage to minimise the error to your origional measurement
+7. Hold both buttons to save and exit to the menu
 
 ### Calibrating tip offset
 
@@ -120,13 +107,13 @@ Some tips will have an offset on their readings, to calibrate this out perform t
 1. Connect power to your iron
 2. Make sure the tip is at room temperature (ie. wait for a fair while after using the iron before calibration)
 3. Enter the settings menu
-4. Scroll down to *TMP CAL*
+4. Scroll down to the advanced menu, and then the temperature calibration
 5. Press the button to change the option (tip button)
 6. The display will start to scroll a warning message to check that the tip is at ambient temperature!
 7. Press the button near the tip of the iron to confirm.
 8. The display will go to "...." for a short period of time as the unit measures the tip temperature and the handle temperature and compares them
 9. The display will then go back to *TMP CAL*
-10. Calibration is done, just exit the settings menu as normal 
+10. Calibration is done, just exit the settings menu as normal
 11. You're done. Enjoy your iron.
 
 ### Boost mode
@@ -135,7 +122,6 @@ This allows you to change the front key (one near the tip) to become a boost but
 
 The boost temperature is set in the settings menu.
 
-
 ## Thanks
 
 If you love this firmware and want to continue my caffine addiction, you can do so here (or email me for other options) : https://paypal.me/RalimTek

workspace/TS100/Makefile

@@ -32,7 +32,7 @@ HEXFILE_DIR=Hexfile
 OUTPUT_DIR=Objects
 
 # code optimisation ------------------------------------------------------------
-OPTIM=-Os -finline-small-functions -findirect-inlining -fdiagnostics-color -ffunction-sections -fdata-sections
+OPTIM=-Os -flto -finline-small-functions -findirect-inlining -fdiagnostics-color -ffunction-sections -fdata-sections
 
 
 # global defines ---------------------------------------------------------------
@@ -73,7 +73,7 @@ LINKER_FLAGS=-Wl,--gc-sections 		\
 			-mcpu=cortex-m3		\
 			-mthumb			\
 			-mfloat-abi=soft	\
-			-lm
+			-lm -Os -flto -Wl,--undefined=vTaskSwitchContext
 
 # compiler flags ---------------------------------------------------------------
 CPUFLAGS=-D GCC_ARMCM3		\
@@ -177,7 +177,7 @@ OUT_OBJS_CPP=$(addprefix $(OUTPUT_DIR)/,$(OBJS_CPP))
 OUT_OBJS_S=$(addprefix $(OUTPUT_DIR)/,$(OBJS_S))
 OUT_HEXFILE=$(addprefix $(HEXFILE_DIR)/,$(OUTPUT_EXE))
 
-all: $(OUT_HEXFILE).hex
+all: $(OUT_HEXFILE).hex $(OUT_HEXFILE).bin
 
 #
 # The rule to create the target directory
@@ -185,13 +185,17 @@ all: $(OUT_HEXFILE).hex
 
 # Create hexfile
 %.hex : %.elf
-	$(SIZE) -x $^
+	$(SIZE) $^
 	$(OBJCOPY) $^ -O ihex $@
 
+%.bin : %.elf
+	$(SIZE) $^
+	$(OBJCOPY) $^ -O binary $@
+
 $(OUT_HEXFILE).elf : $(OUT_OBJS) $(OUT_OBJS_CPP) $(OUT_OBJS_S) Makefile $(LDSCRIPT)
 	@test -d $(@D) || mkdir -p $(@D)
 	@echo Linking $(OUTPUT_EXE).elf
-	@$(CPP) $(CXXFLAGS) $(OUT_OBJS) $(OUT_OBJS_CPP) $(OUT_OBJS_S)  $(LIBS) $(LINKER_FLAGS)
+	@$(CPP) $(CXXFLAGS) $(OUT_OBJS_S) $(OUT_OBJS) $(OUT_OBJS_CPP) $(LIBS) $(LINKER_FLAGS)
 
 $(OUT_OBJS): $(OUTPUT_DIR)/%.o : %.c Makefile
 	@test -d $(@D) || mkdir -p $(@D)

workspace/TS100/build.sh

@@ -35,3 +35,5 @@ make -j16 lang=LT
 rm -rf Objects/src
 make -j16 lang=UA
 rm -rf Objects/src
+make -j16 lang=SR
+rm -rf Objects/src

workspace/TS100/inc/FRToSI2C.hpp

@@ -11,20 +11,28 @@
 #include "cmsis_os.h"
 
 class FRToSI2C {
-public:
-	FRToSI2C(I2C_HandleTypeDef* i2chandle);
-	void FRToSInit();
+  public:
+
+	FRToSI2C(I2C_HandleTypeDef *i2chandle) : i2c(i2chandle),
+											 I2CSemaphore(nullptr) {
+	}
+
+	void FRToSInit() {
+		I2CSemaphore = xSemaphoreCreateBinary();
+		xSemaphoreGive(I2CSemaphore);
+	}
+
 	void CpltCallback(); //Normal Tx Callback
 
 	void Mem_Read(uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize,
-			uint8_t *pData, uint16_t Size);
+				  uint8_t *pData, uint16_t Size);
 	void Mem_Write(uint16_t DevAddress, uint16_t MemAddress,
-			uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+				   uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
 
 	void Transmit(uint16_t DevAddress, uint8_t *pData, uint16_t Size);
 
-private:
-	I2C_HandleTypeDef* i2c;
+  private:
+	I2C_HandleTypeDef *i2c;
 	SemaphoreHandle_t I2CSemaphore;
 };
 

workspace/TS100/inc/Font.h

@@ -602,16 +602,20 @@ const uint8_t SettingsMenuIcons[] = {
 	// Soldering
 	//width = 16
 	//height = 16
-	0x00,0x02,0x04,0x08,0x12,0x24,0xC4,0x42,0x82,0x04,0x00,0x00,0x00,0x00,0x00,0x00,
-	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x02,0x07,0x0A,0x14,0x28,0x50,0x60,0x00,
+		0x00, 0x02, 0x04, 0x08, 0x12, 0x24, 0xC4, 0x42, 0x82, 0x04,
+		0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+		0x00, 0x00, 0x00, 0x01, 0x02, 0x07, 0x0A, 0x14, 0x28, 0x50,
+		0x60, 0x00,
 
 
 
 	//Sleep
 	//width = 16
 	//height = 16
-	0x00,0xC6,0xE6,0xF6,0xBE,0x9E,0x8E,0x86,0x00,0x00,0x40,0x40,0xC0,0xC0,0xC0,0x00,
-	0x00,0x01,0x01,0x01,0x45,0x65,0x75,0x5D,0x4C,0x00,0x06,0x07,0x07,0x05,0x04,0x00,
+	0x00, 0xC6, 0xE6, 0xF6, 0xBE, 0x9E, 0x8E, 0x86, 0x00, 0x00,
+	0x40, 0x40, 0xC0, 0xC0, 0xC0, 0x00, 0x00, 0x01, 0x01, 0x01,
+	0x45, 0x65, 0x75, 0x5D, 0x4C, 0x00, 0x06, 0x07, 0x07, 0x05,
+	0x04, 0x00,
 
 
 
@@ -624,14 +628,18 @@ const uint8_t SettingsMenuIcons[] = {
 	//Wrench
 	///width = 16
 	//height = 16
-	0x00,0x18,0x30,0x32,0x7E,0x7C,0xF0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x0F,0x3E,0x7E,0x4C,0x0C,0x18,0x00,
+	0x00, 0x18, 0x30, 0x32, 0x7E, 0x7C, 0xF0, 0xC0, 0x80, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x01, 0x03, 0x0F, 0x3E, 0x7E, 0x4C, 0x0C,
+	0x18, 0x00,
 	#ifdef NOTUSED
 	//Calibration (Not used, kept for future menu layouts)
 		//width = 16
 		//height = 16
-		0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0xE8,0x70,0x7A,0x5E,0x8E,0x1C,0x30,0x00,
-		0x00,0x10,0x38,0x1C,0x0E,0x07,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x80, 0xC0, 0xE8, 0x70,
+	0x7A, 0x5E, 0x8E, 0x1C, 0x30, 0x00, 0x00, 0x10, 0x38, 0x1C,
+	0x0E, 0x07, 0x03, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00,
 	#endif
 };
 

workspace/TS100/inc/LIS2DH12.hpp

@@ -10,16 +10,16 @@
 #include "stm32f1xx_hal.h"
 #include "FRToSI2C.hpp"
 #include "LIS2DH12_defines.hpp"
+#include "hardware.h"
+
 class LIS2DH12 {
 public:
-	LIS2DH12(FRToSI2C* i2cHandle);
+	LIS2DH12(FRToSI2C* i2cHandle) : i2c(i2cHandle) {}
 	void initalize();
-	uint8_t getOrientation();
+	Orientation getOrientation() { return static_cast<Orientation>((I2C_RegisterRead(LIS_INT2_SRC) >> 2) - 1); }
 	void getAxisReadings(int16_t *x, int16_t *y, int16_t *z);
 
 private:
-	void setSensitivity(uint8_t threshold, uint8_t filterTime);	// Sets the sensitivity of the unit
-
 	void I2C_RegisterWrite(uint8_t reg, uint8_t data);
 	uint8_t I2C_RegisterRead(uint8_t reg);
 	FRToSI2C* i2c;

workspace/TS100/inc/MMA8652FC.hpp

@@ -10,17 +10,18 @@
 #include "stm32f1xx_hal.h"
 #include "MMA8652FC_defines.h"
 #include "FRToSI2C.hpp"
+#include "hardware.h"
+
 class MMA8652FC {
 
 public:
 
-	MMA8652FC(FRToSI2C* i2cHandle);
+	MMA8652FC(FRToSI2C* i2cHandle) : i2c(i2cHandle) {}
 	void initalize();		// Initalize the system
-	uint8_t getOrientation();// Reads the I2C register and returns the orientation (true == left)
+	Orientation getOrientation();// Reads the I2C register and returns the orientation (true == left)
 	void getAxisReadings(int16_t *x, int16_t *y, int16_t *z);
 
 private:
-	void setSensitivity(uint8_t threshold, uint8_t filterTime);	// Sets the sensitivity of the unit
 
 	void I2C_RegisterWrite(uint8_t reg, uint8_t data);
 	uint8_t I2C_RegisterRead(uint8_t reg);

workspace/TS100/inc/OLED.hpp

@@ -12,6 +12,7 @@
 #include <hardware.h>
 #include "stm32f1xx_hal.h"
 #include <stdbool.h>
+#include <string.h>
 #include "FRToSI2C.hpp"
 #include "Font.h"
 #ifdef __cplusplus
@@ -21,34 +22,67 @@ extern "C" {
 #ifdef __cplusplus
 }
 #endif
-#define DEVICEADDR_OLED  (0x3c<<1)
-#define OLED_WIDTH       96
+#define DEVICEADDR_OLED   (0x3c<<1)
+#define OLED_WIDTH        96
+#define FRAMEBUFFER_START 17
+
 
 class OLED {
 public:
-	OLED(FRToSI2C* i2cHandle);	// Initialize Driver and store I2C pointer
+	OLED(FRToSI2C* i2cHandle); // Initialize Driver and store I2C pointer
 	void initialize(); 	// Startup the I2C coms (brings screen out of reset etc)
-	void refresh(); 	// Draw the buffer out to the LCD using the DMA Channel
+	
+	// Draw the buffer out to the LCD using the DMA Channel
+	void refresh() {
+		i2c->Transmit( DEVICEADDR_OLED, screenBuffer, FRAMEBUFFER_START + (OLED_WIDTH * 2));
+		//DMA tx time is ~ 20mS Ensure after calling this you delay for at least 25ms
+		//or we need to goto double buffering
+	}
+
 	void drawChar(char c, char preCursorCommand = '\0'); // Draw a character to a specific location
-	void displayOnOff(bool on);				// Turn the screen on or not
+	// Turn the screen on or not
+	void displayOnOff(bool on) {
+		displayOnOffState = on;
+		screenBuffer[1] = on ? 0xAF : 0xAE;
+	}			
 	void setRotation(bool leftHanded);  	// Set the rotation for the screen
-	bool getRotation();					// Get the current rotation of the LCD
+	// Get the current rotation of the LCD
+	bool getRotation() const {
+		return inLeftHandedMode;
+	}					
 	void print(const char* string);	// Draw a string to the current location, with current font
-	void setCursor(int16_t x, int16_t y);   // Set the cursor location by pixels
-	void setCharCursor(int16_t x, int16_t y); //Set cursor location by chars in current font
+	// Set the cursor location by pixels
+	void setCursor(int16_t x, int16_t y) {
+		cursor_x = x;
+		cursor_y = y;		
+	}   
+	//Set cursor location by chars in current font
+	void setCharCursor(int16_t x, int16_t y) {
+		cursor_x = x * fontWidth;
+		cursor_y = y * fontHeight;
+	}
 	void setFont(uint8_t fontNumber); // (Future) Set the font that is being used
-	void drawImage(const uint8_t* buffer, uint8_t x, uint8_t width);
+	void drawImage(const uint8_t* buffer, uint8_t x, uint8_t width) {
+		drawArea(x, 0, width, 16, buffer);
+	}
 	// Draws an image to the buffer, at x offset from top to bottom (fixed height renders)
 	void printNumber(uint16_t number, uint8_t places);
 	// Draws a number at the current cursor location
-	void clearScreen();						// Clears the buffer
-	void drawBattery(uint8_t state);		// Draws the battery level symbol
-	void drawCheckbox(bool state);		// Draws a checkbox
+	// Clears the buffer
+	void clearScreen() {
+		memset(&screenBuffer[FRAMEBUFFER_START], 0, OLED_WIDTH * 2);
+	}					
+	// Draws the battery level symbol
+	void drawBattery(uint8_t state) {
+		drawSymbol(3 + (state > 10 ? 10 : state));
+	}		
+	// Draws a checkbox
+	void drawCheckbox(bool state) {
+		drawSymbol((state) ? 16 : 17);
+	}
 	void drawSymbol(uint8_t symbolID);//Used for drawing symbols of a predictable width
-	void drawArea(int16_t x, int8_t y, uint8_t wide, uint8_t height,
-			const uint8_t* ptr);
-	void fillArea(int16_t x, int8_t y, uint8_t wide, uint8_t height,
-			const uint8_t value);
+	void drawArea(int16_t x, int8_t y, uint8_t wide, uint8_t height, const uint8_t* ptr); //Draw an area, but y must be aligned on 0/8 offset
+	void fillArea(int16_t x, int8_t y, uint8_t wide, uint8_t height, const uint8_t value); //Fill an area, but y must be aligned on 0/8 offset
 	void drawFilledRect(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1,bool clear);
 	void drawHeatSymbol(uint8_t state);
 private:
@@ -57,7 +91,6 @@ private:
 
 	FRToSI2C* i2c;					//i2c Pointer
 	const uint8_t* currentFont;	// Pointer to the current font used for rendering to the buffer
-	uint8_t screenBuffer[16 + 96 + 96 + 10];    // The data buffer
 	uint8_t* firstStripPtr; // Pointers to the strips to allow for buffer having extra content
 	uint8_t* secondStripPtr;	//Pointers to the strips
 	bool inLeftHandedMode; // Whether the screen is in left or not (used for offsets in GRAM)
@@ -65,6 +98,7 @@ private:
 	uint8_t fontWidth, fontHeight;
 	int16_t cursor_x, cursor_y;
 	uint8_t displayOffset;
+	uint8_t screenBuffer[16 + (OLED_WIDTH * 2) + 10];    // The data buffer
 };
 
 #endif /* OLED_HPP_ */

workspace/TS100/inc/hardware.h

@@ -13,6 +13,12 @@
 extern "C" {
 #endif
 
+enum Orientation {
+    ORIENTATION_LEFT_HAND = 0,
+    ORIENTATION_RIGHT_HAND = 1,
+    ORIENTATION_FLAT = 3
+};
+
 #define KEY_B_Pin GPIO_PIN_6
 #define KEY_B_GPIO_Port GPIOA
 #define TMP36_INPUT_Pin GPIO_PIN_7

workspace/TS100/src/FRToSI2C.cpp

@@ -7,11 +7,6 @@
 
 #include "FRToSI2C.hpp"
 
-FRToSI2C::FRToSI2C(I2C_HandleTypeDef* i2chandle) {
-	i2c = i2chandle;
-	I2CSemaphore = NULL;
-}
-
 void FRToSI2C::CpltCallback() {
 	BaseType_t xHigherPriorityTaskWoken = pdFALSE;
 	i2c->State = HAL_I2C_STATE_READY;//Force state reset
@@ -19,8 +14,6 @@ void FRToSI2C::CpltCallback() {
 		xSemaphoreGiveFromISR(I2CSemaphore, &xHigherPriorityTaskWoken);
 		portYIELD_FROM_ISR(xHigherPriorityTaskWoken);
 	}
-
-
 }
 
 void FRToSI2C::Mem_Read(uint16_t DevAddress, uint16_t MemAddress,
@@ -69,14 +62,7 @@ void FRToSI2C::Mem_Write(uint16_t DevAddress, uint16_t MemAddress,
 		} else {
 			NVIC_SystemReset();
 		}
-
 	}
-
-}
-
-void FRToSI2C::FRToSInit() {
-	I2CSemaphore = xSemaphoreCreateBinary();
-	xSemaphoreGive(I2CSemaphore);
 }
 
 void FRToSI2C::Transmit(uint16_t DevAddress, uint8_t* pData, uint16_t Size) {

workspace/TS100/src/LIS2DH12.cpp

@@ -7,39 +7,32 @@
 
 #include <LIS2DH12.hpp>
 #include "cmsis_os.h"
-LIS2DH12::LIS2DH12(FRToSI2C* i2cHandle) {
-	i2c = i2cHandle;
-}
+
+typedef struct {
+        const uint8_t reg;
+        const uint8_t value;
+} LIS_REG;
+
+static const LIS_REG i2c_registers[] = {
+        {LIS_CTRL_REG1, 0x17}, // 25Hz
+        {LIS_CTRL_REG2, 0b00001000}, // Highpass filter off
+        {LIS_CTRL_REG3, 0b01100000}, // Setup interrupt pins
+        {LIS_CTRL_REG4, 0b00001000}, // Block update mode off, HR on
+        {LIS_CTRL_REG5, 0b00000010},
+        {LIS_CTRL_REG6, 0b01100010},
+        //Basically setup the unit to run, and enable 4D orientation detection
+        {LIS_INT2_CFG, 0b01111110}, //setup for movement detection
+        {LIS_INT2_THS, 0x28},
+        {LIS_INT2_DURATION, 64},
+        {LIS_INT1_CFG, 0b01111110},
+        {LIS_INT1_THS, 0x28},
+        {LIS_INT1_DURATION, 64}
+};
 
 void LIS2DH12::initalize() {
-	I2C_RegisterWrite(LIS_CTRL_REG1, 0x17); //25Hz
-	I2C_RegisterWrite(LIS_CTRL_REG2, 0b00001000); //Highpass filter off
-	I2C_RegisterWrite(LIS_CTRL_REG3, 0b01100000); //Setup interrupt pins
-	I2C_RegisterWrite(LIS_CTRL_REG4, 0b00001000); //Block update mode off,HR on
-	I2C_RegisterWrite(LIS_CTRL_REG5, 0b00000010);
-	I2C_RegisterWrite(LIS_CTRL_REG6, 0b01100010);
-
-	//Basically setup the unit to run, and enable 4D orientation detection
-	I2C_RegisterWrite(LIS_INT2_CFG, 0b01111110); //setup for movement detection
-	I2C_RegisterWrite(LIS_INT2_THS, 0x28);
-	I2C_RegisterWrite(LIS_INT2_DURATION, 64);
-	I2C_RegisterWrite(LIS_INT1_CFG, 0b01111110); //setup for movement detection
-	I2C_RegisterWrite(LIS_INT1_THS, 0x28);
-	I2C_RegisterWrite(LIS_INT1_DURATION, 64);
-
-}
-
-//0=no change, 1= right handed, 2= left handed
-uint8_t LIS2DH12::getOrientation() {
-	// 8=right handed,4=left,16=flat
-	//So we ignore if not 8/4
-	uint8_t pos = I2C_RegisterRead(LIS_INT2_SRC);
-	if (pos == 8)
-		return 1;
-	else if (pos == 4)
-		return 2;
-	else
-		return 0;
+    for (size_t index = 0; index < (sizeof(i2c_registers) / sizeof(i2c_registers[0])); index++) {
+		I2C_RegisterWrite(i2c_registers[index].reg, i2c_registers[index].value);
+    }
 }
 
 void LIS2DH12::getAxisReadings(int16_t* x, int16_t* y, int16_t* z) {
@@ -52,9 +45,6 @@ void LIS2DH12::getAxisReadings(int16_t* x, int16_t* y, int16_t* z) {
 	(*z) = ((uint16_t) (tempArr[5] << 8 | tempArr[4]));
 }
 
-void LIS2DH12::setSensitivity(uint8_t threshold, uint8_t filterTime) {
-}
-
 void LIS2DH12::I2C_RegisterWrite(uint8_t reg, uint8_t data) {
 	i2c->Mem_Write(LIS2DH_I2C_ADDRESS, reg, I2C_MEMADD_SIZE_8BIT, &data, 1);
 

workspace/TS100/src/MMA8652FC.cpp

@@ -8,9 +8,26 @@
 #include <MMA8652FC.hpp>
 #include "cmsis_os.h"
 
-MMA8652FC::MMA8652FC(FRToSI2C* i2cHandle) {
-	i2c = i2cHandle;
-}
+typedef struct {
+        const uint8_t reg;
+        const uint8_t val;
+} MMA_REG;
+
+static const MMA_REG i2c_registers[] = {
+        {CTRL_REG2, 0},    //Normal mode
+        {CTRL_REG2, 0x40},      // Reset all registers to POR values
+        {FF_MT_CFG_REG, 0x78}, // Enable motion detection for X, Y, Z axis, latch disabled
+        {PL_CFG_REG, 0x40},     //Enable the orientation detection
+        {PL_COUNT_REG, 200},    //200 count debounce
+        {PL_BF_ZCOMP_REG, 0b01000111}, //Set the threshold to 42 degrees
+        {P_L_THS_REG, 0b10011100},    //Up the trip angles
+        {CTRL_REG4, 0x01 | (1 << 4)}, // Enable dataready interrupt & orientation interrupt
+        {CTRL_REG5, 0x01}, // Route data ready interrupts to INT1 ->PB5 ->EXTI5, leaving orientation routed to INT2
+        {CTRL_REG2, 0x12},   //Set maximum resolution oversampling
+        {XYZ_DATA_CFG_REG, (1 << 4)}, //select high pass filtered data
+        {HP_FILTER_CUTOFF_REG, 0x03}, //select high pass filtered data
+        {CTRL_REG1, 0x19} // ODR=12 Hz, Active mode
+};
 
 void MMA8652FC::I2C_RegisterWrite(uint8_t reg, uint8_t data) {
 	i2c->Mem_Write( MMA8652FC_I2C_ADDRESS, reg, I2C_MEMADD_SIZE_8BIT, &data, 1);
@@ -24,47 +41,34 @@ uint8_t MMA8652FC::I2C_RegisterRead(uint8_t reg) {
 	return tx_data[0];
 }
 void MMA8652FC::initalize() {
+	size_t index = 0;
+
 	//send all the init commands to the unit
-	I2C_RegisterWrite(CTRL_REG2, 0);    //Normal mode
-	I2C_RegisterWrite( CTRL_REG2, 0x40);	// Reset all registers to POR values
+
+	I2C_RegisterWrite(i2c_registers[index].reg, i2c_registers[index].val); index++;
+	I2C_RegisterWrite(i2c_registers[index].reg, i2c_registers[index].val); index++;
+
 	HAL_Delay(2);		// ~1ms delay
-	I2C_RegisterWrite(FF_MT_CFG_REG, 0x78); // Enable motion detection for X, Y, Z axis, latch disabled
-
-	I2C_RegisterWrite(PL_CFG_REG, 0x40);	//Enable the orientation detection
-	I2C_RegisterWrite(PL_COUNT_REG, 200);    //200 count debounce
-	I2C_RegisterWrite(PL_BF_ZCOMP_REG, 0b01000111); //Set the threshold to 42 degrees
-	I2C_RegisterWrite(P_L_THS_REG, 0b10011100);    //Up the trip angles
-	I2C_RegisterWrite( CTRL_REG4, 0); // Disable IRQ's
-	I2C_RegisterWrite( CTRL_REG5, 0x01); // Route data ready interrupts to INT1 ->PB5 ->EXTI5, leaving orientation routed to INT2
-	I2C_RegisterWrite( CTRL_REG2, 0x12);   //Set maximum resolution oversampling
-	I2C_RegisterWrite( XYZ_DATA_CFG_REG, (1 << 4)); //select high pass filtered data
-	I2C_RegisterWrite( HP_FILTER_CUTOFF_REG, 0x03); //select high pass filtered data
-
-	I2C_RegisterWrite( CTRL_REG1, 0x19);		// ODR=12 Hz, Active mode
 
+	while (index < (sizeof(i2c_registers) / sizeof(i2c_registers[0]))) {
+		I2C_RegisterWrite(i2c_registers[index].reg, i2c_registers[index].val); index++;
+	}
 }
 
-void MMA8652FC::setSensitivity(uint8_t threshold, uint8_t filterTime) {
-	uint8_t sens = 9 * 2 + 17;
-	sens -= 2 * threshold;
-	I2C_RegisterWrite( CTRL_REG1, 0);		//  sleep mode
-	I2C_RegisterWrite(FF_MT_THS_REG, (sens & 0x7F));// Set accumulation threshold
-	I2C_RegisterWrite(FF_MT_COUNT_REG, filterTime);    // Set debounce threshold
-	I2C_RegisterWrite( CTRL_REG1, 0x31);		// ODR=12 Hz, Active mode
-}
-
-uint8_t MMA8652FC::getOrientation() {
+Orientation MMA8652FC::getOrientation() {
 	//First read the PL_STATUS register
 	uint8_t plStatus = I2C_RegisterRead(PL_STATUS_REG);
 	if ((plStatus & 0b10000000) == 0b10000000) {
 		plStatus >>= 1;    //We don't need the up/down bit
 		plStatus &= 0x03;    //mask to the two lower bits
+
 		//0 == left handed
 		//1 == right handed
 
-		return plStatus == 0 ? 2 : 1;
-	} else
-		return 0;
+		return static_cast<Orientation>(plStatus);
+	}
+	
+	return ORIENTATION_FLAT;
 }
 void MMA8652FC::getAxisReadings(int16_t *x, int16_t *y, int16_t *z) {
 	uint8_t tempArr[6];

workspace/TS100/src/OLED.cpp

@@ -13,7 +13,6 @@
 /*http://www.displayfuture.com/Display/datasheet/controller/SSD1307.pdf*/
 /*All commands are prefixed with 0x80*/
 /*Data packets are prefixed with 0x40*/
-const uint8_t configLength = 50;
 uint8_t OLED_Setup_Array[] = { /**/
 0x80, 0xAE,/*Display off*/
 0x80, 0xD5,/*Set display clock divide ratio / osc freq*/
@@ -43,54 +42,42 @@ uint8_t OLED_Setup_Array[] = { /**/
 };
 //Setup based on the SSD1307 and modified for the SSD1306
 
+const uint8_t REFRESH_COMMANDS[17] = {
+	0x80, 0xAF,
+	0x80, 0x21,
+	0x80, 0x20,
+	0x80, 0x7F,
+	0x80, 0xC0,
+	0x80, 0x22,
+	0x80, 0x00,
+	0x80, 0x01,
+	0x40
+};
+
 OLED::OLED(FRToSI2C* i2cHandle) {
 	i2c = i2cHandle;
 	cursor_x = cursor_y = 0;
 	currentFont = FONT_12;
 	fontWidth = 12;
 	inLeftHandedMode = false;
-	firstStripPtr = &screenBuffer[16 + 1];
-	secondStripPtr = &screenBuffer[16 + 1 + 96];
+	firstStripPtr = &screenBuffer[FRAMEBUFFER_START];
+	secondStripPtr = &screenBuffer[FRAMEBUFFER_START + OLED_WIDTH];
 	fontHeight = 16;
-	fontWidth = 12;
 	displayOffset = 0;
 	displayOnOffState = true;
-
 }
 
 void OLED::initialize() {
+	memcpy(&screenBuffer[0], &REFRESH_COMMANDS[0], sizeof(REFRESH_COMMANDS));
+
 	HAL_Delay(5);
 	HAL_GPIO_WritePin(OLED_RESET_GPIO_Port, OLED_RESET_Pin, GPIO_PIN_SET);
 	HAL_Delay(10);
 	//Send the setup settings
-	i2c->Transmit( DEVICEADDR_OLED, (uint8_t*) OLED_Setup_Array, configLength);
+	i2c->Transmit( DEVICEADDR_OLED, (uint8_t*) OLED_Setup_Array, sizeof(OLED_Setup_Array));
 	displayOnOff(true);
 }
 
-//Write out the buffer to the OLEd & call any rendering objects
-void OLED::refresh() {
-	screenBuffer[0] = 0x80;
-	screenBuffer[1] = displayOnOffState ? 0xAF : 0xAE;
-	screenBuffer[2] = 0x80;
-	screenBuffer[3] = 0x21;
-	screenBuffer[4] = 0x80;
-	screenBuffer[5] = inLeftHandedMode ? 0 : 32; //display is shifted by 32 in left handed mode as driver ram is 128 wide
-	screenBuffer[6] = 0x80;
-	screenBuffer[7] = inLeftHandedMode ? 95 : 0x7F; //End address of the ram segment we are writing to (96 wide)
-	screenBuffer[8] = 0x80; /*Set COM Scan direction*/
-	screenBuffer[9] = inLeftHandedMode ? 0xC8 : 0xC0;
-	screenBuffer[10] = 0x80;    //Set pages to rollover after 2
-	screenBuffer[11] = 0x22;
-	screenBuffer[12] = 0x80;
-	screenBuffer[13] = 0x00;    //start page 0
-	screenBuffer[14] = 0x80;
-	screenBuffer[15] = 0x01;
-	screenBuffer[16] = 0x40;    //start of data marker
-
-	i2c->Transmit( DEVICEADDR_OLED, screenBuffer, 16 + (96 * 2) + 1);
-
-}
-
 /*
  * Prints a char to the screen.
  * UTF font handling is done using the two input chars.
@@ -151,25 +138,26 @@ void OLED::drawChar(char c, char PrecursorCommand) {
 	cursor_x += fontWidth;
 }
 
-void OLED::displayOnOff(bool on) {
-	displayOnOffState = on;
-}
-
 void OLED::setRotation(bool leftHanded) {
-	if (inLeftHandedMode != leftHanded) {
-		//send command struct again with changes
-		if (leftHanded == 1) {
+	if (inLeftHandedMode == leftHanded) {
+		return;
+	}
+
+	//send command struct again with changes
+	if (leftHanded) {
 			OLED_Setup_Array[11] = 0xC8;    //c1?
 			OLED_Setup_Array[19] = 0xA1;
-		} else if (leftHanded == 0) {
+	} else {
 			OLED_Setup_Array[11] = 0xC0;
 			OLED_Setup_Array[19] = 0xA0;
 		}
-		i2c->Transmit( DEVICEADDR_OLED, (uint8_t*) OLED_Setup_Array,
-				configLength);
+	i2c->Transmit( DEVICEADDR_OLED, (uint8_t*) OLED_Setup_Array, sizeof(OLED_Setup_Array));
 		inLeftHandedMode = leftHanded;
+
+	screenBuffer[5] = inLeftHandedMode ? 0 : 32; //display is shifted by 32 in left handed mode as driver ram is 128 wide
+	screenBuffer[7] = inLeftHandedMode ? 95 : 0x7F; //End address of the ram segment we are writing to (96 wide)
+	screenBuffer[9] = inLeftHandedMode ? 0xC8 : 0xC0;
 	}
-}
 
 //print a string to the current cursor location
 void OLED::print(const char* str) {
@@ -183,14 +171,6 @@ void OLED::print(const char* str) {
 	}
 }
 
-void OLED::setCursor(int16_t x, int16_t y) {
-	cursor_x = x;
-	cursor_y = y;
-}
-void OLED::setCharCursor(int16_t x, int16_t y) {
-	cursor_x = x * fontWidth;
-	cursor_y = y * fontHeight;
-}
 void OLED::setFont(uint8_t fontNumber) {
 	if (fontNumber == 1) {
 		//small font
@@ -208,58 +188,35 @@ void OLED::setFont(uint8_t fontNumber) {
 	}
 }
 
-void OLED::drawImage(const uint8_t* buffer, uint8_t x, uint8_t width) {
-	drawArea(x, 0, width, 16, buffer);
-}
-
 //maximum places is 5
 void OLED::printNumber(uint16_t number, uint8_t places) {
-	char buffer[6];
-	buffer[5] = 0;    //null
+	char buffer[6] = { 0 };
+	
 	if (places == 5) {
 		buffer[4] = '0' + number % 10;
 		number /= 10;
-	} else
-		buffer[4] = 0;
+	}
 
 	if (places > 3) {
 		buffer[3] = '0' + number % 10;
 		number /= 10;
-	} else
-		buffer[3] = 0;
+	}
 
 	if (places > 2) {
 		buffer[2] = '0' + number % 10;
 		number /= 10;
-	} else
-		buffer[2] = 0;
+	}
 
 	if (places > 1) {
 		buffer[1] = '0' + number % 10;
 		number /= 10;
-	} else
-		buffer[1] = 0;
+	}
+
 	buffer[0] = '0' + number % 10;
 	number /= 10;
 	print(buffer);
 }
 
-void OLED::clearScreen() {
-	memset(firstStripPtr, 0, 96);
-	memset(secondStripPtr, 0, 96);
-}
-
-bool OLED::getRotation() {
-	return inLeftHandedMode;
-}
-void OLED::drawBattery(uint8_t state) {
-	if (state > 10)
-		state = 10;
-	drawSymbol(3 + state);
-}
-void OLED::drawCheckbox(bool state) {
-	drawSymbol((state) ? 16 : 17);
-}
 void OLED::drawSymbol(uint8_t symbolID) {
 	//draw a symbol to the current cursor location
 	setFont(2);

workspace/TS100/src/gui.cpp

@@ -191,14 +191,14 @@ const menuitem advancedMenu[] = {
 		settings_displayCalibrateVIN } }, /*Voltage input cal*/
 #ifdef PIDSETTINGS
 
-{ (const char*) SettingsDescriptions[17], { settings_setPIDP }, {
-		settings_displayPIDP } }, /*Voltage input cal*/
-{ (const char*) SettingsDescriptions[18], { settings_setPIDI }, {
-		settings_displayPIDI } }, /*Voltage input cal*/
-{ (const char*) SettingsDescriptions[19], { settings_setPIDD }, {
-		settings_displayPIDD } }, /*Voltage input cal*/
+		{	(const char*) SettingsDescriptions[17], {settings_setPIDP}, {
+				settings_displayPIDP}}, /*Voltage input cal*/
+		{	(const char*) SettingsDescriptions[18], {settings_setPIDI}, {
+				settings_displayPIDI}}, /*Voltage input cal*/
+		{	(const char*) SettingsDescriptions[19], {settings_setPIDD}, {
+				settings_displayPIDD}}, /*Voltage input cal*/
 #endif
-{ NULL, { NULL }, { NULL } }            // end of menu marker. DO NOT REMOVE
+		{ NULL, { NULL }, { NULL } }        // end of menu marker. DO NOT REMOVE
 };
 
 static void printShortDescriptionSingleLine(uint32_t shortDescIndex) {
@@ -279,7 +279,7 @@ static int userConfirmation(const char* message) {
 
 		if (lcdRefresh) {
 			lcd.refresh();
-			osDelay(20);
+			osDelay(40);
 			lcdRefresh = false;
 		}
 	}
@@ -628,14 +628,14 @@ static void settings_setCalibrateVIN(void) {
 		case BUTTON_B_LONG:
 			saveSettings();
 			return;
-
+			break;
 		case BUTTON_NONE:
 		default:
 			break;
 		}
 
 		lcd.refresh();
-		osDelay(50);
+		osDelay(40);
 
 		// Cap to sensible values
 		if (systemSettings.voltageDiv < 90) {
@@ -646,55 +646,40 @@ static void settings_setCalibrateVIN(void) {
 	}
 }
 
-static void settings_displayCalibrateVIN(void) {
-	printShortDescription(14, 5);
-}
-static void settings_displaySolderingMenu(void) {
+static void displayMenu(size_t index) {
 	//Call into the menu
 	lcd.setFont(1);
 	lcd.setCursor(0, 0);
 	//Draw title
-	lcd.print(SettingsMenuEntries[0]);
+	lcd.print(SettingsMenuEntries[index]);
 	//Draw symbol
 	//16 pixel wide image
-	lcd.drawArea(96 - 16, 0, 16, 16, (&SettingsMenuIcons[(16 * 2) * 0]));
+	lcd.drawArea(96 - 16, 0, 16, 16, (&SettingsMenuIcons[(16 * 2) * index]));
+}
+
+static void settings_displayCalibrateVIN(void) {
+	printShortDescription(14, 5);
+}
+static void settings_displaySolderingMenu(void) {
+	displayMenu(0);
 }
 static void settings_enterSolderingMenu(void) {
 	gui_Menu(solderingMenu);
 }
 static void settings_displayPowerMenu(void) {
-	lcd.setFont(1);
-	lcd.setCursor(0, 0);
-	//Draw title
-	lcd.print(SettingsMenuEntries[1]);
-	//Draw symbol
-	//16 pixel wide image
-	lcd.drawArea(96 - 16, 0, 16, 16, (&SettingsMenuIcons[(16 * 2) * 1]));
+	displayMenu(1);
 }
 static void settings_enterPowerMenu(void) {
 	gui_Menu(PowerMenu);
 }
 static void settings_displayUIMenu(void) {
-	lcd.setFont(1);
-	lcd.setCursor(0, 0);
-	//Draw title
-	lcd.print(SettingsMenuEntries[2]);
-	//Draw symbol
-	//16 pixel wide image
-	lcd.drawArea(96 - 16, 0, 16, 16, (&SettingsMenuIcons[(16 * 2) * 2]));
+	displayMenu(2);
 }
 static void settings_enterUIMenu(void) {
 	gui_Menu(UIMenu);
 }
 static void settings_displayAdvancedMenu(void) {
-	lcd.setFont(1);
-	lcd.setCursor(0, 0);
-	//Draw title
-	lcd.print(SettingsMenuEntries[3]);
-	//Draw symbol
-	//16 pixel wide image
-	lcd.drawArea(96 - 16, 0, 16, 16, (&SettingsMenuIcons[(16 * 2) * 3]));
-
+	displayMenu(3);
 }
 static void settings_enterAdvancedMenu(void) {
 	gui_Menu(advancedMenu);
@@ -807,7 +792,7 @@ void gui_Menu(const menuitem* menu) {
 
 		if (lcdRefresh) {
 			lcd.refresh();  // update the LCD
-			osDelay(20);
+			osDelay(40);
 			lcdRefresh = false;
 		}
 	}

workspace/TS100/src/hardware.c

@@ -63,12 +63,15 @@ uint16_t getTipRawTemp(uint8_t instant) {
 	static int64_t filterFP = 0;
 	const uint8_t filterBeta = 5; //higher values smooth out more, but reduce responsiveness
 
-	if (instant) {
+	if (instant == 1) {
 		uint16_t itemp = getTipInstantTemperature();
 		filterFP = (filterFP << filterBeta) - filterFP;
 		filterFP += (itemp << 9);
 		filterFP = filterFP >> filterBeta;
 		return itemp;
+	} else if (instant == 2) {
+		filterFP = (getTipInstantTemperature() << 9);
+		return filterFP >> 9;
 	} else {
 		return filterFP >> 9;
 	}

workspace/TS100/src/main.cpp

@@ -97,7 +97,7 @@ void printVoltage() {
 	lcd.printNumber(getInputVoltageX10(systemSettings.voltageDiv) % 10, 1);
 }
 void GUIDelay() {
-	osDelay(66);  // 15Hz
+	osDelay(50);
 }
 void gui_drawTipTemp(bool symbol) {
 	// Draw tip temp handling unit conversion & tolerance near setpoint
@@ -193,13 +193,13 @@ static void waitForButtonPress() {
 	ButtonState buttons = getButtonState();
 	while (buttons) {
 		buttons = getButtonState();
-		GUIDelay();
 		lcd.refresh();
+		GUIDelay();
 	}
 	while (!buttons) {
 		buttons = getButtonState();
-		GUIDelay();
 		lcd.refresh();
+		GUIDelay();
 	}
 }
 
@@ -263,6 +263,8 @@ static void gui_drawBatteryIcon() {
 static void gui_solderingTempAdjust() {
 	uint32_t lastChange = xTaskGetTickCount();
 	currentlyActiveTemperatureTarget = 0;
+	uint32_t autoRepeatTimer = 0;
+	uint8_t autoRepeatAcceleration = 0;
 	for (;;) {
 		lcd.setCursor(0, 0);
 		lcd.clearScreen();
@@ -279,28 +281,35 @@ static void gui_solderingTempAdjust() {
 			return;
 			break;
 		case BUTTON_B_LONG:
-
+			if (xTaskGetTickCount() - autoRepeatTimer
+					+ autoRepeatAcceleration> PRESS_ACCEL_INTERVAL_MAX) {
+				systemSettings.SolderingTemp -= 10;  // sub 10
+				autoRepeatTimer = xTaskGetTickCount();
+				autoRepeatAcceleration += PRESS_ACCEL_STEP;
+			}
 			break;
 		case BUTTON_F_LONG:
-
+			if (xTaskGetTickCount() - autoRepeatTimer
+					+ autoRepeatAcceleration> PRESS_ACCEL_INTERVAL_MAX) {
+				systemSettings.SolderingTemp += 10;
+				autoRepeatTimer = xTaskGetTickCount();
+				autoRepeatAcceleration += PRESS_ACCEL_STEP;
+			}
 			break;
 		case BUTTON_F_SHORT:
-			if (lcd.getRotation()) {
-				systemSettings.SolderingTemp += 10;  // add 10
-			} else {
-				systemSettings.SolderingTemp -= 10;  // sub 10
-			}
+			systemSettings.SolderingTemp += 10;  // add 10
 			break;
 		case BUTTON_B_SHORT:
-			if (!lcd.getRotation()) {
-				systemSettings.SolderingTemp += 10;  // add 10
-			} else {
-				systemSettings.SolderingTemp -= 10;  // sub 10
-			}
+			systemSettings.SolderingTemp -= 10;  // sub 10
 			break;
 		default:
 			break;
 		}
+		if ((PRESS_ACCEL_INTERVAL_MAX - autoRepeatAcceleration)
+				< PRESS_ACCEL_INTERVAL_MIN) {
+			autoRepeatAcceleration = PRESS_ACCEL_INTERVAL_MAX
+					- PRESS_ACCEL_INTERVAL_MIN;
+		}
 		// constrain between 50-450 C
 		if (systemSettings.temperatureInF) {
 			if (systemSettings.SolderingTemp > 850)
@@ -320,7 +329,12 @@ static void gui_solderingTempAdjust() {
 
 		if (xTaskGetTickCount() - lastChange > 200)
 			return;  // exit if user just doesn't press anything for a bit
-		lcd.drawChar('-');
+
+		if (lcd.getRotation())
+			lcd.drawChar('-');
+		else
+			lcd.drawChar('+');
+
 		lcd.drawChar(' ');
 		lcd.printNumber(systemSettings.SolderingTemp, 3);
 		if (systemSettings.temperatureInF)
@@ -328,7 +342,10 @@ static void gui_solderingTempAdjust() {
 		else
 			lcd.drawSymbol(1);
 		lcd.drawChar(' ');
-		lcd.drawChar('+');
+		if (lcd.getRotation())
+				lcd.drawChar('+');
+			else
+				lcd.drawChar('-');
 		lcd.refresh();
 		GUIDelay();
 	}
@@ -407,6 +424,25 @@ static int gui_SolderingSleepingMode() {
 	}
 	return 0;
 }
+
+static void display_countdown(int sleepThres) {
+	/*
+	 * Print seconds or minutes (if > 99 seconds) until sleep
+	 * mode is triggered.
+	 */
+	int lastEventTime =
+			lastButtonTime < lastMovementTime ?
+					lastMovementTime : lastButtonTime;
+	int downCount = sleepThres - xTaskGetTickCount() + lastEventTime;
+	if (downCount > 9900) {
+		lcd.printNumber(downCount / 6000 + 1, 2);
+		lcd.print("M");
+	} else {
+		lcd.printNumber(downCount / 100 + 1, 2);
+		lcd.print("S");
+	}
+}
+
 static void gui_solderingMode() {
 	/*
 	 * * Soldering (gui_solderingMode)
@@ -477,6 +513,11 @@ static void gui_solderingMode() {
 				lcd.printNumber(getTipPWM(), 3);
 				lcd.print("%");
 
+				if (systemSettings.sensitivity && systemSettings.SleepTime) {
+					lcd.print(" ");
+					display_countdown(sleepThres);
+				}
+
 				lcd.setCursor(0, 8);
 				lcd.print(SleepingTipAdvancedString);
 				gui_drawTipTemp(true);
@@ -553,6 +594,10 @@ static void gui_solderingMode() {
 	}
 }
 
+static const char *HEADERS[] = {
+__DATE__, "Heap: ", "HWMG: ", "HWMP: ", "HWMM: ", "Time: ", "Move: ", "Rtip: ",
+		"Ctip: ", "Vin :" };
+
 void showVersion(void) {
 	uint8_t screen = 0;
 	ButtonState b;
@@ -563,35 +608,36 @@ void showVersion(void) {
 		lcd.print((char *) "V2.05 PCB");  // Print version number
 		lcd.printNumber(PCBVersion, 1); //Print PCB ID number
 		lcd.setCursor(0, 8);         // second line
+		lcd.print(HEADERS[screen]);
 		switch (screen) {
-		case 0:
-			lcd.print(__DATE__);         // print the compile date
-			break;
 		case 1:
-			lcd.print("Heap: ");
 			lcd.printNumber(xPortGetFreeHeapSize(), 5);
 			break;
 		case 2:
-			lcd.print("HWMG: ");
 			lcd.printNumber(uxTaskGetStackHighWaterMark(GUITaskHandle), 5);
 			break;
 		case 3:
-			lcd.print("HWMP: ");
 			lcd.printNumber(uxTaskGetStackHighWaterMark(PIDTaskHandle), 5);
 			break;
 		case 4:
-			lcd.print("HWMM: ");
 			lcd.printNumber(uxTaskGetStackHighWaterMark(MOVTaskHandle), 5);
 			break;
-
 		case 5:
-			lcd.print("Time: ");
 			lcd.printNumber(xTaskGetTickCount() / 100, 5);
 			break;
 		case 6:
-			lcd.print("Move: ");
 			lcd.printNumber(lastMovementTime / 100, 5);
-
+			break;
+		case 7:
+			lcd.printNumber(getTipRawTemp(0), 5);
+			break;
+		case 8:
+			lcd.printNumber(tipMeasurementToC(getTipRawTemp(0)), 5);
+			break;
+		case 9:
+			printVoltage();
+			break;
+		default:
 			break;
 		}
 
@@ -601,8 +647,9 @@ void showVersion(void) {
 			return;
 		else if (b == BUTTON_F_SHORT) {
 			screen++;
-			screen = screen % 7;
+			screen = screen % 10;
 		}
+		GUIDelay();
 	}
 }
 
@@ -611,20 +658,9 @@ void startGUITask(void const *argument) {
 	i2cDev.FRToSInit();
 	uint8_t tempWarningState = 0;
 	bool buttonLockout = false;
-
-	switch (systemSettings.OrientationMode) {
-	case 0:
-		lcd.setRotation(false);
-		break;
-	case 1:
-		lcd.setRotation(true);
-		break;
-	case 2:
-		lcd.setRotation(false);
-		break;
-	default:
-		break;
-	}
+	bool tempOnDisplay = false;
+	getTipRawTemp(2);         //reset filter
+	lcd.setRotation(systemSettings.OrientationMode & 1);
 	uint32_t ticks = xTaskGetTickCount();
 	ticks += 400;  //4 seconds from now
 	while (xTaskGetTickCount() < ticks) {
@@ -748,7 +784,11 @@ void startGUITask(void const *argument) {
 				lcd.setCursor(84, 0);
 				gui_drawBatteryIcon();
 			}
-			if (tipTemp > 50) {
+			if (tipTemp > 55)
+				tempOnDisplay = true;
+			else if (tipTemp < 45)
+				tempOnDisplay = false;
+			if (tempOnDisplay) {
 				//draw temp over the start soldering button
 				//Location changes on screen rotation
 				if (lcd.getRotation()) {
@@ -762,7 +802,9 @@ void startGUITask(void const *argument) {
 				}
 				//draw in the temp
 				lcd.setFont(0);				//big font
-				gui_drawTipTemp(false);				// draw in the temp
+				if (!(systemSettings.coolingTempBlink
+						&& (xTaskGetTickCount() % 50 < 25)))
+					gui_drawTipTemp(false);				// draw in the temp
 			}
 		}
 
@@ -812,7 +854,8 @@ void startPIDTask(void const *argument) {
 
 				int32_t rawTempError = currentlyActiveTemperatureTarget
 						- rawTemp;
-				int32_t ierror = (rawTempError / ((int32_t)systemSettings.PID_I));
+				int32_t ierror = (rawTempError
+						/ ((int32_t) systemSettings.PID_I));
 				integralCount += ierror;
 				if (integralCount > (itermMax / 2))
 					integralCount = itermMax / 2;  // prevent too much lead
@@ -822,11 +865,12 @@ void startPIDTask(void const *argument) {
 				int32_t dInput = (rawTemp - derivativeLastValue);
 
 				/*Compute PID Output*/
-				int32_t output = (rawTempError / ((int32_t)systemSettings.PID_P));
-				if (((int32_t)systemSettings.PID_I))
+				int32_t output = (rawTempError
+						/ ((int32_t) systemSettings.PID_P));
+				if (((int32_t) systemSettings.PID_I))
 					output += integralCount;
-				if (((int32_t)systemSettings.PID_D))
-					output -= (dInput / ((int32_t)systemSettings.PID_D));
+				if (((int32_t) systemSettings.PID_D))
+					output -= (dInput / ((int32_t) systemSettings.PID_D));
 
 				if (output > 100) {
 					output = 100;  // saturate
@@ -853,35 +897,20 @@ void startPIDTask(void const *argument) {
 #define MOVFilter 8
 void startMOVTask(void const *argument) {
 	osDelay(250);  // wait for accelerometer to stabilize
-	switch (systemSettings.OrientationMode) {
-	case 0:
-		lcd.setRotation(false);
-		break;
-	case 1:
-		lcd.setRotation(true);
-		break;
-	case 2:
-		lcd.setRotation(false);
-		break;
-	default:
-		break;
-	}
+	lcd.setRotation(systemSettings.OrientationMode & 1);
 	lastMovementTime = 0;
-	int16_t datax[MOVFilter];
-	int16_t datay[MOVFilter];
-	int16_t dataz[MOVFilter];
+	int16_t datax[MOVFilter] = { 0 };
+	int16_t datay[MOVFilter] = { 0 };
+	int16_t dataz[MOVFilter] = { 0 };
 	uint8_t currentPointer = 0;
-	memset(datax, 0, MOVFilter * sizeof(int16_t));
-	memset(datay, 0, MOVFilter * sizeof(int16_t));
-	memset(dataz, 0, MOVFilter * sizeof(int16_t));
-	int16_t tx, ty, tz;
-	int32_t avgx, avgy, avgz;
+	int16_t tx = 0, ty = 0, tz = 0;
+	int32_t avgx = 0, avgy = 0, avgz = 0;
 	if (systemSettings.sensitivity > 9)
 		systemSettings.sensitivity = 9;
 #if ACCELDEBUG
 	uint32_t max = 0;
 #endif
-	uint8_t rotation = 0;
+	Orientation rotation = ORIENTATION_FLAT;
 	for (;;) {
 		int32_t threshold = 1500 + (9 * 200);
 		threshold -= systemSettings.sensitivity * 200; // 200 is the step size
@@ -894,19 +923,16 @@ void startMOVTask(void const *argument) {
 			rotation = accel.getOrientation();
 		}
 		if (systemSettings.OrientationMode == 2) {
-			if (rotation != 0) {
-				lcd.setRotation(rotation == 2);  // link the data through
+			if (rotation != ORIENTATION_FLAT) {
+				lcd.setRotation(rotation == ORIENTATION_LEFT_HAND); // link the data through
 			}
 		}
 		datax[currentPointer] = (int32_t) tx;
 		datay[currentPointer] = (int32_t) ty;
 		dataz[currentPointer] = (int32_t) tz;
 		currentPointer = (currentPointer + 1) % MOVFilter;
-#if ACCELDEBUG
 
-		// Debug for Accel
-
-		avgx = avgy = avgz = 0;
+		// calculate averages
 		for (uint8_t i = 0; i < MOVFilter; i++) {
 			avgx += datax[i];
 			avgy += datay[i];
@@ -915,38 +941,35 @@ void startMOVTask(void const *argument) {
 		avgx /= MOVFilter;
 		avgy /= MOVFilter;
 		avgz /= MOVFilter;
+
+		//Sum the deltas
+		int32_t error = (abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz));
+
+#if ACCELDEBUG
+		// Debug for Accel
+
 		lcd.setFont(1);
 		lcd.setCursor(0, 0);
 		lcd.printNumber(abs(avgx - (int32_t) tx), 5);
 		lcd.print(" ");
 		lcd.printNumber(abs(avgy - (int32_t) ty), 5);
-		if ((abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz)) > max)
-		max = (abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz));
+		if (error > max) {
+			max = (abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz));
+		}
 		lcd.setCursor(0, 8);
 		lcd.printNumber(max, 5);
 		lcd.print(" ");
 
 		lcd.printNumber((abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz)), 5);
 		lcd.refresh();
-		if (HAL_GPIO_ReadPin(KEY_A_GPIO_Port, KEY_A_Pin) == GPIO_PIN_RESET)
-		max = 0;
-#endif
-
-		// calculate averages
-		avgx = avgy = avgz = 0;
-		for (uint8_t i = 0; i < MOVFilter; i++) {
-			avgx += datax[i];
-			avgy += datay[i];
-			avgz += dataz[i];
+		if (HAL_GPIO_ReadPin(KEY_A_GPIO_Port, KEY_A_Pin) == GPIO_PIN_RESET) {
+			max = 0;
 		}
-		avgx /= MOVFilter;
-		avgy /= MOVFilter;
-		avgz /= MOVFilter;
+#endif
 
 		// So now we have averages, we want to look if these are different by more
 		// than the threshold
-		//Sum the deltas
-		int32_t error = (abs(avgx - tx) + abs(avgy - ty) + abs(avgz - tz));
+
 		// If error has occurred then we update the tick timer
 		if (error > threshold) {
 			lastMovementTime = xTaskGetTickCount();