Patch to handle UTF slightly better.

Not perfect but working for now
Update strings to be more uniform
2025-02-26 07:53:55 +00:00 · 2017-09-17 12:21:25 +10:00 · 2017-09-17 11:50:44 +10:00 · 2017-09-09 23:13:21 +10:00 · 2017-08-29 20:06:00 +10:00 · 2017-08-26 16:54:09 +10:00
28 changed files with 2019 additions and 600 deletions
--- a/.gitignore
+++ b/.gitignore
@@ -39,4 +39,5 @@ workspace/ts100/.settings/language.settings.xml
 workspace/ts100/.cproject
 TS100/KiCad/TS100.bak
 Logo GUI/TS100 Logo Editor/TS100 Logo Editor/obj/
-Logo GUI/TS100 Logo Editor/TS100 Logo Editor/bin/
+Logo GUI/TS100 Logo Editor/TS100 Logo Editor/bin/
+workspace/ts100/ts100.xml
--- a/History.md
+++ b/History.md
@@ -0,0 +1,79 @@
+# Version Changes
+
+V1.17
+
+* Added blinking cooldown display
+* Allowed smaller sleep timeout values
+* New font!
+* Automatic startup option
+
+V1.16
+
+* Added automatic rotation support
+* Added power display graph
+
+V1.15
+
+* Added support for a custom bootup logo to be programmed via the DFU bootloader.
+
+V1.14
+
+* Changed input voltage cutoff to be based on cell count rather than voltage.
+
+V1.13
+
+* Swapped buttons for menu to prevent accidentally changing first menu item
+* Added auto key repeat.
+
+V1.12
+
+* Increases sensitivity options to be 1*9 with 0 off state
+* Fixes issue where going from COOL *> soldering can leave screen off.
+
+V1.11
+
+* Boost mode
+* Change sensitivity options to be 1*8
+
+V1.10
+
+* Adds help text to settings
+* Improves settings for the display update rate
+
+V1.09
+
+* Adds display modes, for slowing down or simplifying the display
+
+V1.08
+
+* Fix settings menu not showing flip display
+
+V1.07
+
+* Adds shutdown time to automatically shutdown the iron after inactivity
+
+V1.06
+
+* Changes H and C when the iron is heating to the minidso chevron like images
+
+V1.05
+
+* Adds ability to calibrate the input voltage measurement
+
+V1.04
+
+* Increased accuracy of the temperature control
+* Improved PID response slightly
+* Allows temperature offset calibration
+* Nicer idle screen
+
+V1.03 
+
+* Improved Button handling
+* Ability to set motion sensitivity
+* DC voltmeter page shows input voltage
+
+V1.02
+
+* Adds hold both buttons on IDLE to access the therometer mode.
+* Changes the exit soldering mode to be holding both buttons (Like original firmware).
--- a/Editor.userprefs
+++ b/Editor.userprefs
@@ -0,0 +1,8 @@
+<Properties StartupItem="TS100 Logo Editor/TS100 Logo Editor.csproj">
+  <MonoDevelop.Ide.Workspace ActiveConfiguration="Debug" />
+  <MonoDevelop.Ide.Workbench />
+  <MonoDevelop.Ide.DebuggingService.Breakpoints>
+    <BreakpointStore />
+  </MonoDevelop.Ide.DebuggingService.Breakpoints>
+  <MonoDevelop.Ide.DebuggingService.PinnedWatches />
+</Properties>
--- a/README.md
+++ b/README.md
@@ -1,6 +1,7 @@
 # TS100
-This is a complete re*write of the open source software for the ts100 soldering iron.
+This is a complete rewrite of the open source software for the ts100 soldering iron.
 This project is feature complete for use as a soldering iron, *so please suggest any feature improvements you would like!*
+A short(ish) video that goes through every single menu option in the firmware is available [over here](https://www.youtube.com/watch?v=WlnpboYfxNk)

 This project was started to remove the need for USB for changing system settings.
 In the latest official firmware they have also added a settings menu system, so it is still worth comparing the two firmwares to select your preferred option.
@@ -23,11 +24,13 @@ Please calibrate your irons voltage reading when you are using a lithium battery
 * Boost mode lets you temporarily change the temperature when soldering
 * Battery charge level indicatior if power source set to a lipo cell count.
 * Custom bootup logo support
+* Automatic LCD rotation based on orientation

 # Upgrading your ts100 iron

-This is completely safe, if it goes wrong just put the .hex file from the official website onto the unit and your back to the old firmware. Downloads for the hex files to flash are available on the [releases page.](https://github.com/Ralim/ts100/releases)
-Officially the bootloader on the iron only works under windows. However, users have reported that it does work under Mac, and can be made to work under Linux *sometimes*. Details over on the [wiki page](https://github.com/Ralim/ts100/wiki/Upgrading*Firmware).
+This is completely safe, if it goes wrong just put the .hex file from the official website onto the unit and your back to the old firmware. Downloads for the hex files to flash are available on the [releases page.](https://github.com/Ralim/ts100/releases) The file you want is called *ts100.hex* unless you want the translations, they are ts100_*language short name*.hex.
+
+Officially the bootloader on the iron only works under windows. However, users have reported that it does work under Mac, and can be made to work under Linux *sometimes*. Details over on the [wiki page](https://github.com/Ralim/ts100/wiki/Upgrading-Firmware).

 1. Hold the button closest to the tip, and plug in the USB to the computer.
 2. The unit will appear as a USB drive.
@@ -45,18 +48,7 @@ There is a complete device flash backup included in this repository. (Note this

 This firmware uses a different method of updating the bootup image.
 This removes the need for emulating a USB drive on the iron just to allow for a bootup image to be setup.
-At this point in time you will need a windows machine to make the required .hex file for you image.
-
-1. On the [releases page](https://github.com/Ralim/ts100/releases) you will need to download the latest copy of the GUI Tool (*TS100 Logo Editor.exe*).
-2. Launch the TS100 Logo Editor, you will need to have .NET 4.0 installed on your machine
-3. On the tool open the source image that you would like to use as your bootup screen. A resolution of 96x16 is ideal, but you can fill or stretch your logo to fit
-4. Colour images are okay, the software will convert them to B&W for you.
-5. You can also invert colours if you would prefer.
-6. Save the created file as a *.hex* file somewhere.
-7. Connect your iron to your computer in DFU mode (same as you would to upgrade firmware).
-8. Drag the created .hex file for the logo onto the iron to update it with the file.
-9. You should be good to go.
-10. The image will stay through future updates, but if it ever wont I will put a warning in the update download on the releases page.
+There are further instructions on the [wiki](https://github.com/Ralim/ts100/wiki/Logo-Editor). Instructions are kept on the wiki so that users can update the information if they find extra helpful information.

 ## New Menu System

@@ -86,7 +78,7 @@ If you leave the unit alone (ie don't press any buttons) on a setting, after 3 s
 * TMPUNIT -> Temperature unit, C or F
 * TMPRND -> Temperature Rounding, {1,5,10}
 * TMPSPD -> How fast the temperature should update in the soldering status screen.
-* FLPDSP -> Flip display for left handed users
+* DSPROT -> Display rotation mode, Automatic, Left handed or Right handed
 * BOOST -> Enable boost mode
 * BTMP -> Set the temperature for the boost mode

@@ -144,72 +136,11 @@ This allows you to change the front key (one near the tip) to become a boost but

 The boost temperature is set in the settings menu.

-## Version Changes
+## Commercial Use

-V1.15
+This software is provided as-is, so I cannot provide any commercial support for the firmware. However you are more than welcome to distribute links to the firmware, or provide irons with this software on them. 
+Please do not re-host the files, but rather link to this page, so that there are not old versions of the firmware hanging around. If this firmware does make you money, it would be nice to recieve a donation, however I dont enforce this.

-* Added support for a custom bootup logo to be programmed via the DFU bootloader.
+## Thanks

-V1.14
-
-* Changed input voltage cutoff to be based on cell count rather than voltage.
-
-V1.13
-
-* Swapped buttons for menu to prevent accidentally changing first menu item
-* Added auto key repeat.
-
-V1.12
-
-* Increases sensitivity options to be 1*9 with 0 off state
-* Fixes issue where going from COOL *> soldering can leave screen off.
-
-V1.11
-
-* Boost mode
-* Change sensitivity options to be 1*8
-
-V1.10
-
-* Adds help text to settings
-* Improves settings for the display update rate
-
-V1.09
-
-* Adds display modes, for slowing down or simplifying the display
-
-V1.08
-
-* Fix settings menu not showing flip display
-
-V1.07
-
-* Adds shutdown time to automatically shutdown the iron after inactivity
-
-V1.06
-
-* Changes H and C when the iron is heating to the minidso chevron like images
-
-V1.05
-
-* Adds ability to calibrate the input voltage measurement
-
-V1.04
-
-* Increased accuracy of the temperature control
-* Improved PID response slightly
-* Allows temperature offset calibration
-* Nicer idle screen
-
-V1.03 
-
-* Improved Button handling
-* Ability to set motion sensitivity
-* DC voltmeter page shows input voltage
-
-V1.02
-
-* Adds hold both buttons on IDLE to access the therometer mode.
-* Changes the exit soldering mode to be holding both buttons (Like original firmware).
-
-If you love this firmware and want to continue my caffine addiction, you can do so here (or email me) : https://paypal.me/RalimTek
+If you love this firmware and want to continue my caffine addiction, you can do so here (or email me for other options) : https://paypal.me/RalimTek
--- a/flash/flash_ts100_linux.sh
+++ b/flash/flash_ts100_linux.sh
@@ -0,0 +1,130 @@
+#!/bin/bash
+# TS100 Flasher for Linux by Alex Wigen (https://github.com/awigen)
+
+DIR_TMP="/tmp/ts100"
+
+function usage() {
+    echo
+    echo "#################"
+    echo "# TS100 Flasher #"
+    echo "#################"
+    echo
+    echo " Usage: $0 <HEXFILE>"
+    echo
+    echo "This script has been tested to work on Fedora."
+    echo "If you experience any issues please open a ticket at:"
+    echo "https://github.com/Ralim/ts100/issues/new"
+    echo
+}
+
+GAUTOMOUNT=0
+function disable_gautomount {
+    GSETTINGS=`which gsettings`
+    if [ $? -ne 0 ]; then
+        return 1
+    fi
+    gsettings get org.gnome.desktop.media-handling automount | grep true > /dev/null
+    if [ $? -eq 0 ]; then
+        GAUTOMOUNT=1
+        gsettings set org.gnome.desktop.media-handling automount false
+    fi
+}
+
+function enable_gautomount {
+    if [ "$GAUTOMOUNT" -ne 0 ]; then
+        gsettings set org.gnome.desktop.media-handling automount true
+    fi
+}
+
+function is_attached {
+    output=`lsblk -b --raw --output NAME,MODEL | grep 'DFU\\\\x20Disk'`
+    if [ $? -ne 0 ]; then
+      return 1
+    fi
+    DEVICE=`echo $output | awk '{print "/dev/"$1}'`
+}
+
+instructions="not printed"
+function wait_for_ts100 {
+    is_attached
+    while [ $? -ne 0 ]; do
+        if [ "$instructions" = "not printed" ]; then
+            echo
+            echo "#####################################################"
+            echo "#   Waiting for TS100 config disk device to appear  #"
+            echo "#                                                   #"
+            echo "# Connect the soldering iron with a USB cable while #"
+            echo "# holding the button closest to the tip pressed     #"
+            echo "#####################################################"
+            echo
+            instructions="printed"
+        fi
+        sleep 0.1
+        is_attached
+    done
+}
+
+function mount_ts100 {
+    mkdir -p "$DIR_TMP"
+    sudo mount -t msdos -o uid=$UID "$DEVICE" "$DIR_TMP"
+    if [ $? -ne 0 ]; then
+        echo "Failed to mount $DEVICE on $DIR_TMP"
+        exit 1
+    fi
+}
+
+function umount_ts100 {
+    mountpoint "$DIR_TMP" > /dev/null && sudo umount "$DIR_TMP"
+    if [ $? -ne 0 ]; then
+        echo "Failed to unmount $DIR_TMP"
+        exit 1
+    fi
+    rmdir "$DIR_TMP"
+}
+
+function cleanup {
+    enable_gautomount
+    if [ -d "$DIR_TMP" ]; then
+        umount_ts100
+    fi
+}
+trap cleanup EXIT
+
+if [ "$#" -ne 1 ]; then
+    echo "Please provide a HEX file to flash"
+    usage
+    exit 1
+fi
+
+if [ ! -f "$1" ]; then
+    echo "'$1' is not a regular file, please provide a HEX file to flash"
+    usage
+    exit 1
+fi
+
+if [ `head -c1 "$1"` != ":" ] || [ `tail -n1 "$1" | head -c1` != ":" ]; then
+    echo "'$1' doesn't look like a valid HEX file. Please provide a HEX file to flash"
+    usage
+    exit 1
+fi
+
+disable_gautomount
+
+wait_for_ts100
+echo "Found TS100 config disk device on $DEVICE"
+
+mount_ts100
+echo "Mounted config disk drive, flashing..."
+cp -v "$1" "$DIR_TMP/ts100.hex"
+sync
+
+echo "Waiting for TS100 to flash"
+sleep 5
+
+echo "Remounting config disk drive"
+umount_ts100
+wait_for_ts100
+mount_ts100
+
+echo "Flash result: "
+ls "$DIR_TMP"/ts100*
--- a/python_logo_converter/img2ts100.py
+++ b/python_logo_converter/img2ts100.py
@@ -0,0 +1,251 @@
+#!/usr/bin/env python
+
+VERSION_STRING = '0.01'
+
+
+import os
+import sys
+
+try:
+    import PIL, PIL.Image, PIL.ImageOps
+except ImportError,error:
+    raise ImportError,   "%s: %s requres Python Imaging Library (PIL). " \
+                         "Install with `pip` or OS-specific package " \
+                         "management tool." \
+                       % (error, sys.argv[0])
+
+
+
+LCD_WIDTH       = 96
+LCD_HEIGHT      = 16
+LCD_NUM_BYTES   = LCD_WIDTH * LCD_HEIGHT / 8
+LCD_PADDED_SIZE = 1024
+
+INTELHEX_DATA_RECORD                    = 0x00
+INTELHEX_END_OF_FILE_RECORD             = 0x01
+INTELHEX_EXTENDED_LINEAR_ADDRESS_RECORD = 0x04
+INTELHEX_BYTES_PER_LINE                 = 16
+INTELHEX_MINIMUM_SIZE                   = 4096
+
+
+
+def split16(word):
+    '''return high and low byte of 16-bit word value as tuple'''
+    return ((word >> 8) & 0xff, word & 0xff)
+
+
+
+def intel_hex_line(file, record_type, offset, data):
+    '''write a line of data in Intel hex format'''
+    # length, address offset, record type
+    record_length = len(data)
+    file.write(':%02X%04X%02X' % (record_length, offset, record_type))
+
+    # data
+    map(lambda byte: file.write("%02X" % byte), data)
+
+    # compute and write checksum (with DOS line ending for compatibility/safety)
+    file.write(   "%02X\r\n"
+                % (  (  (  sum(data,                    # sum data ...
+                                 record_length          # ... and other ...
+                               + sum(split16(offset))   # ... fields ...
+                               + record_type)           # ... on line
+                         & 0xff)                        # low 8 bits
+                      ^ 0xff)                           # two's ...
+                   + 1))                                # ... complement
+
+
+
+def intel_hex(file, bytes, start_address = 0x0):
+    '''write block of data in Intel hex format'''
+    if len(bytes) % INTELHEX_BYTES_PER_LINE != 0:
+        raise ValueError, \
+                "Program error: Size of LCD data is not evenly divisible by %s" \
+              % INTELHEX_BYTES_PER_LINE
+
+    address_lo =  start_address        & 0xffff
+    address_hi = (start_address >> 16) & 0xffff
+
+    intel_hex_line(file,
+                   INTELHEX_EXTENDED_LINEAR_ADDRESS_RECORD,
+                   0,
+                   split16(address_hi))
+
+    size_written = 0
+    while size_written < INTELHEX_MINIMUM_SIZE:
+        offset = address_lo
+        for line_start in range(0, len(bytes), INTELHEX_BYTES_PER_LINE):
+            intel_hex_line(file,
+                           INTELHEX_DATA_RECORD,
+                           offset,
+                           bytes[line_start:line_start+INTELHEX_BYTES_PER_LINE])
+            size_written += INTELHEX_BYTES_PER_LINE
+            if size_written >= INTELHEX_MINIMUM_SIZE:
+                break
+            offset += INTELHEX_BYTES_PER_LINE
+
+    intel_hex_line(file, INTELHEX_END_OF_FILE_RECORD, 0, ())
+
+
+
+def img2hex(input_filename,
+            output_file,
+            preview_filename=None,
+            threshold=128,
+            dither=False,
+            negative=False):
+    '''
+    Convert 'input_filename' image file into Intel hex format with data
+        formatted for display on TS100 LCD and file object.
+    Input image is converted from color or grayscale to black-and-white,
+        and resized to fit TS100 LCD screen as necessary.
+    Optionally write resized/thresholded/black-and-white preview image
+        to file specified by name.
+    Optional `threshold' argument 8 bit value; grayscale pixels greater than
+        this become 1 (white) in output, less than become 0 (black).
+    Unless optional `dither', in which case PIL grayscale-to-black/white
+        dithering algorithm used.
+    Optional `negative' inverts black/white regardless of input image type
+        or other options.
+    '''
+
+    try:
+        image = PIL.Image.open(input_filename)
+    except BaseException,error:
+        raise IOError, \
+              "error reading image file \"%s\": %s" % (input_filename, error)
+
+    # convert to luminance
+    # do even if already black/white because PIL can't invert 1-bit so
+    #   can't just pass thru in case --negative flag
+    # also resizing works better in luminance than black/white
+    # also no information loss converting black/white to grayscale
+    if image.mode != 'L':
+        image = image.convert('L')
+
+    if image.size != (LCD_WIDTH, LCD_HEIGHT):
+        image = image.resize((LCD_WIDTH, LCD_HEIGHT), PIL.Image.BICUBIC)
+
+    if negative:
+        image = PIL.ImageOps.invert(image)
+        threshold = 255 - threshold  # have to invert threshold
+
+    if dither:
+        image = image.convert('1')
+    else:
+        image = image.point(lambda pixel: 0 if pixel < threshold else 1, '1')
+
+    if preview_filename: image.save(preview_filename)
+
+    ''' DEBUG
+    for row in range(LCD_HEIGHT):
+        for column in range(LCD_WIDTH):
+            if image.getpixel((column, row)): sys.stderr.write('1')
+            else:                             sys.stderr.write('0')
+        sys.stderr.write('\n')
+    '''
+
+    # pad to this size (also will be repeated in output Intel hex file)
+    data = [0] * LCD_PADDED_SIZE
+
+    # magic/undocumented/required header in endian-reverse byte order
+    data[0] = 0x55
+    data[1] = 0xAA
+    data[2] = 0x0D
+    data[3] = 0xF0
+
+    # convert to TS100 LCD format
+    for ndx in range(LCD_WIDTH * 16 / 8):
+        bottom_half_offset = 0 if ndx < LCD_WIDTH else 8
+        byte = 0
+        for y in range(8):
+            if image.getpixel((ndx % LCD_WIDTH, y + bottom_half_offset)):
+                byte |= 1 << y
+        # store in endian-reversed byte order
+        data[4 + ndx + (1 if ndx % 2 == 0 else -1)] = byte
+
+    intel_hex(output_file, data, 0x0800B800)
+
+
+
+def parse_commandline():
+    parser = argparse.ArgumentParser(
+                formatter_class=argparse.ArgumentDefaultsHelpFormatter,
+                description="Convert image file for display on TS100 LCD "
+                            "at startup")
+
+    def zero_to_255(text):
+        try:
+            value = int(text)
+            assert(value >= 0 and value <= 255)
+        except:
+            raise argparse.ArgumentTypeError("must be integer from 0 to 255 ")
+        return value
+
+    parser.add_argument('input_filename',
+                        help="input image file")
+
+    parser.add_argument('output_filename',
+                        help="output Intel hex file")
+
+    parser.add_argument('-p', '--preview',
+                        help="filename of image preview (same data as "
+                             "Intel hex file, as will appear on TS100 LCD)")
+
+    parser.add_argument('-n', '--negative',
+                        action='store_true',
+                        help="photo negative: exchange black and white "
+                              "in output")
+
+    parser.add_argument('-t', '--threshold',
+                        type=zero_to_255,
+                        default=128,
+                        help="0 to 255: gray (or color converted to gray) "
+                             "above this becomes white, below becomes black; "
+                             "ignored if using --dither")
+
+    parser.add_argument('-d', '--dither',
+                        action='store_true',
+                        help="use dithering (speckling) to convert gray or "
+                             "color to black and white")
+
+    parser.add_argument('-f', '--force',
+                        action='store_true',
+                        help="force overwriting of existing files")
+
+    parser.add_argument('-v', '--version',
+                        action='version',
+                        version="%(prog)s version " +  VERSION_STRING,
+                        help="print version info")
+
+    return parser.parse_args()
+
+
+
+if __name__ == "__main__":
+    import argparse
+    args = parse_commandline()
+
+    if os.path.exists(args.output_filename) and not args.force:
+        sys.stderr.write(  "Won't overwrite existing file \"%s\" (use --force "
+                           "option to override)\n"
+                         % args.output_filename)
+        sys.exit(1)
+
+    if args.preview and os.path.exists(args.preview) and not args.force:
+        sys.stderr.write(  "Won't overwrite existing file \"%s\" (use --force "
+                           "option to override)\n"
+                         % args.preview)
+        sys.exit(1)
+
+    try:
+        with open(args.output_filename, 'w') as output_file:
+            img2hex(args.input_filename,
+                    output_file,
+                    args.preview,
+                    args.threshold,
+                    args.dither,
+                    args.negative)
+    except BaseException,error:
+        sys.stderr.write("Error converting file: %s\n" % error)
+        sys.exit(1)
--- a/workspace/ts100/.cproject
+++ b/workspace/ts100/.cproject
@@ -28,7 +28,7 @@
 							</builder>
 							<tool id="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.1500724168" name="MCU GCC Compiler" superClass="fr.ac6.managedbuild.tool.gnu.cross.c.compiler">
 								<option id="fr.ac6.managedbuild.gnu.c.compiler.option.optimization.level.963224364" name="Optimization Level" superClass="fr.ac6.managedbuild.gnu.c.compiler.option.optimization.level" useByScannerDiscovery="false" value="fr.ac6.managedbuild.gnu.c.optimization.level.more" valueType="enumerated"/>
-								<option id="gnu.c.compiler.option.debugging.level.400507088" name="Debug Level" superClass="gnu.c.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.c.debugging.level.max" valueType="enumerated"/>
+								<option id="gnu.c.compiler.option.debugging.level.400507088" name="Debug Level" superClass="gnu.c.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.c.debugging.level.none" valueType="enumerated"/>
 								<option id="gnu.c.compiler.option.include.paths.1436405353" name="Include paths (-I)" superClass="gnu.c.compiler.option.include.paths" useByScannerDiscovery="false" valueType="includePath">
 									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/inc}&quot;"/>
 									<listOptionValue builtIn="false" value="&quot;${workspace_loc:/${ProjName}/StdPeriph_Driver/inc}&quot;"/>
@@ -50,6 +50,8 @@
 								<option id="gnu.c.compiler.option.dialect.std.1983627145" name="Language standard" superClass="gnu.c.compiler.option.dialect.std" useByScannerDiscovery="true" value="gnu.c.compiler.dialect.c11" valueType="enumerated"/>
 								<option id="gnu.c.compiler.option.warnings.nowarn.1227270879" name="Inhibit all warnings (-w)" superClass="gnu.c.compiler.option.warnings.nowarn" useByScannerDiscovery="false" value="false" valueType="boolean"/>
 								<option id="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.fdata.1556802580" name="Place the data in their own section (-fdata-sections)" superClass="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.fdata" useByScannerDiscovery="false" value="true" valueType="boolean"/>
+								<option id="gnu.c.compiler.option.warnings.extrawarn.826041739" name="Extra warnings (-Wextra)" superClass="gnu.c.compiler.option.warnings.extrawarn" useByScannerDiscovery="false" value="true" valueType="boolean"/>
+								<option id="fr.ac6.managedbuid.gnu.c.compiler.option.misc.other.1256666959" name="Other flags" superClass="fr.ac6.managedbuid.gnu.c.compiler.option.misc.other" useByScannerDiscovery="false" value="-fmessage-length=0 -fno-common" valueType="string"/>
 								<inputType id="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.input.c.1635097739" superClass="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.input.c"/>
 								<inputType id="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.input.s.211510996" superClass="fr.ac6.managedbuild.tool.gnu.cross.c.compiler.input.s"/>
 							</tool>
@@ -186,4 +188,5 @@
 			<resource resourceType="PROJECT" workspacePath="/ts100"/>
 		</configuration>
 	</storageModule>
+	<storageModule moduleId="org.eclipse.cdt.make.core.buildtargets"/>
 </cproject>
--- a/workspace/ts100/StdPeriph_Driver/inc/stm32f10x_i2c.h
+++ b/workspace/ts100/StdPeriph_Driver/inc/stm32f10x_i2c.h
@@ -406,12 +406,12 @@ typedef struct
  * 1) In normal case (only one address managed by the slave), when the address 
  *   sent by the master matches the own address of the peripheral (configured by 
  *   I2C_OwnAddress1 field) the I2C_EVENT_SLAVE_XXX_ADDRESS_MATCHED event is set 
-  *   (where XXX could be TRANSMITTER or RECEIVER).
+  *   (where XX could be TRANSMITTER or RECEIVER).
  *    
  * 2) In case the address sent by the master matches the second address of the 
  *   peripheral (configured by the function I2C_OwnAddress2Config() and enabled 
  *   by the function I2C_DualAddressCmd()) the events I2C_EVENT_SLAVE_XXX_SECONDADDRESS_MATCHED 
-  *   (where XXX could be TRANSMITTER or RECEIVER) are set.
+  *   (where XX could be TRANSMITTER or RECEIVER) are set.
  *   
  * 3) In case the address sent by the master is General Call (address 0x00) and 
  *   if the General Call is enabled for the peripheral (using function I2C_GeneralCallCmd()) 
--- a/workspace/ts100/inc/Font.h
+++ b/workspace/ts100/inc/Font.h
@@ -14,92 +14,260 @@
 */
 #define FONT_WIDTH 12 /*How many pixels wide the font is*/
 const uint8_t FONT[]={
-		0x00,0xF0,0xFC,0x0E,0x82,0xC2,0x62,0x1E,0xFC,0xF0,0x00,0x00,
-		0x00,0x03,0x0F,0x1F,0x11,0x10,0x10,0x1C,0x0F,0x03,0x00,0x00,/*0*/
-		0x00,0x08,0x04,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,/*1*/
-		0x00,0x04,0x02,0x02,0x02,0xC6,0xFC,0x78,0x00,0x00,0x00,0x00,
-		0x00,0x18,0x1C,0x16,0x13,0x11,0x10,0x10,0x10,0x00,0x00,0x00,/*2*/
-		0x00,0x02,0x02,0x42,0x42,0x66,0xFE,0x9C,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,/*3*/
-		0x00,0x00,0x80,0xE0,0x30,0x1C,0x06,0xFE,0xFE,0x00,0x00,0x00,
-		0x00,0x03,0x03,0x02,0x02,0x02,0x02,0x1F,0x1F,0x02,0x02,0x00,/*4*/
-		0x00,0x7E,0x7E,0x42,0x42,0x42,0xC2,0x82,0x00,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x10,0x10,0x08,0x0F,0x07,0x00,0x00,0x00,/*5*/
-		0x00,0xE0,0xF8,0x8C,0x44,0x42,0x42,0xC2,0x82,0x80,0x00,0x00,
-		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,/*6*/
-		0x00,0x02,0x02,0x02,0x02,0xC2,0xF2,0x1E,0x06,0x00,0x00,0x00,
-		0x00,0x00,0x10,0x1C,0x0F,0x03,0x00,0x00,0x00,0x00,0x00,0x00,/*7*/
-		0x00,0x38,0x7C,0x66,0xC2,0x82,0xC2,0x66,0x7C,0x3C,0x00,0x00,
-		0x00,0x0E,0x0F,0x19,0x10,0x10,0x10,0x19,0x0F,0x0E,0x00,0x00,/*8*/
-		0x00,0x78,0x7C,0xC6,0x82,0x82,0x82,0x46,0xFC,0xF8,0x00,0x00,
-		0x00,0x00,0x10,0x10,0x10,0x10,0x08,0x0C,0x07,0x03,0x00,0x00,/*9*/
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//blank
+		0x00,0x00,0x00,0x00,0x7C,0xFF,0xFF,0x7C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x33,0x00,0x00,0x00,0x00,0x00,//!
+		0x00,0x00,0x00,0x3C,0x3C,0x00,0x00,0x3C,0x3C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//"
+		0x00,0x00,0x10,0x90,0xF0,0x7E,0x1E,0x90,0xF0,0x7E,0x1E,0x10,0x00,0x02,0x1E,0x1F,0x03,0x02,0x1E,0x1F,0x03,0x02,0x00,0x00,//#
+		0x00,0x00,0x78,0xFC,0xCC,0xFF,0xFF,0xCC,0xCC,0x88,0x00,0x00,0x00,0x00,0x04,0x0C,0x0C,0x3F,0x3F,0x0C,0x0F,0x07,0x00,0x00,//$
+		0x00,0x00,0x38,0x38,0x38,0x00,0x80,0xC0,0xE0,0x70,0x38,0x1C,0x00,0x30,0x38,0x1C,0x0E,0x07,0x03,0x01,0x38,0x38,0x38,0x00,//%
+		0x00,0x00,0x00,0xB8,0xFC,0xC6,0xE2,0x3E,0x1C,0x00,0x00,0x00,0x00,0x00,0x1F,0x3F,0x31,0x21,0x37,0x1E,0x1C,0x36,0x22,0x00,//&
+		0x00,0x00,0x00,0x00,0x27,0x3F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//'
+		0x00,0x00,0x00,0xF0,0xFC,0xFE,0x07,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0F,0x1F,0x38,0x20,0x20,0x00,0x00,0x00,//(
+		0x00,0x00,0x00,0x01,0x01,0x07,0xFE,0xFC,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x38,0x1F,0x0F,0x03,0x00,0x00,0x00,//)
+		0x00,0x00,0x98,0xB8,0xE0,0xF8,0xF8,0xE0,0xB8,0x98,0x00,0x00,0x00,0x00,0x0C,0x0E,0x03,0x0F,0x0F,0x03,0x0E,0x0C,0x00,0x00,// *
+		0x00,0x00,0x80,0x80,0x80,0xF0,0xF0,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x0F,0x0F,0x01,0x01,0x01,0x00,0x00,//+
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xB8,0xF8,0x78,0x00,0x00,0x00,0x00,0x00,//,
+		0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00,0x00,//-
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x38,0x38,0x00,0x00,0x00,0x00,0x00,//.
+		0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0xE0,0x70,0x38,0x1C,0x0E,0x00,0x18,0x1C,0x0E,0x07,0x03,0x01,0x00,0x00,0x00,0x00,0x00,// /

-		0x00,0x00,0x80,0xF0,0x1E,0x02,0x1E,0xF0,0x80,0x00,0x00,0x00,
-		0x00,0x1C,0x0F,0x03,0x02,0x02,0x02,0x03,0x0F,0x1C,0x00,0x00,/*A*/
-		0x00,0xFE,0xFE,0x42,0x42,0x42,0xE6,0xBE,0x9C,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,/*B*/
-		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x02,0x02,0x04,0x00,0x00,0x00,
-		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x08,0x00,0x00,0x00,/*C*/
-		0x00,0xFE,0xFE,0x02,0x02,0x02,0x06,0x0C,0xFC,0xF0,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x18,0x0C,0x07,0x03,0x00,0x00,/*D*/
-		0x00,0xFE,0xFE,0x42,0x42,0x42,0x42,0x42,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,/*E*/
-		0x00,0xFE,0xFE,0x82,0x82,0x82,0x82,0x82,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*F*/
-		0x00,0xF0,0xF8,0x0C,0x06,0x02,0x82,0x82,0x82,0x84,0x00,0x00,
-		0x00,0x03,0x0F,0x0C,0x18,0x10,0x10,0x10,0x1F,0x1F,0x00,0x00,/*G*/
-		0x00,0xFE,0xFE,0x40,0x40,0x40,0x40,0xFE,0xFE,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,/*H*/
-		0x00,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,
-		0x00,0x10,0x10,0x10,0x1F,0x1F,0x10,0x10,0x10,0x00,0x00,0x00,/*I*/
-		0x00,0x02,0x02,0x02,0x02,0x02,0xFE,0xFE,0x00,0x00,0x00,0x00,
-		0x00,0x08,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,0x00,0x00,/*J*/
-		0x00,0xFE,0xFE,0xC0,0xE0,0x30,0x18,0x0C,0x06,0x02,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x01,0x03,0x06,0x0C,0x18,0x10,0x00,0x00,/*K*/
-		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x10,0x10,0x10,0x10,0x10,0x00,0x00,0x00,0x00,/*L*/
-		0x00,0x00,0xFE,0x06,0x3C,0xC0,0xC0,0x3C,0x06,0xFE,0x00,0x00,
-		0x00,0x10,0x1F,0x00,0x00,0x01,0x01,0x00,0x00,0x1F,0x18,0x00,/*M*/
-		0x00,0xFE,0xFE,0x1E,0x70,0x80,0x00,0xFE,0xFE,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x03,0x1C,0x1F,0x1F,0x00,0x00,0x00,/*N*/
-		0x00,0xF0,0xFC,0x0C,0x02,0x02,0x02,0x0E,0xFC,0xF0,0x00,0x00,
-		0x00,0x03,0x0F,0x1C,0x10,0x10,0x10,0x0C,0x0F,0x03,0x00,0x00,/*O*/
-		0x00,0xFE,0xFE,0x02,0x02,0x02,0x86,0xFC,0x78,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,/*P*/
-		0x00,0xF0,0xF8,0x0C,0x02,0x02,0x02,0x02,0x0C,0xFC,0xF0,0x00,
-		0x00,0x03,0x0F,0x1C,0x10,0x30,0x70,0xD8,0x8C,0x8F,0x83,0x40,/*Q*/
-		0x00,0xFE,0xFE,0x42,0x42,0xC2,0xE6,0x3C,0x1C,0x00,0x00,0x00,
-		0x00,0x1F,0x1F,0x00,0x00,0x00,0x01,0x0F,0x1C,0x10,0x00,0x00,/*R*/
-		0x00,0x38,0x7C,0x66,0xC2,0xC2,0x82,0x84,0x00,0x00,0x00,0x00,
-		0x00,0x08,0x10,0x10,0x10,0x10,0x19,0x0F,0x07,0x00,0x00,0x00,/*S*/
-		0x00,0x02,0x02,0x02,0x02,0xFE,0xFE,0x02,0x02,0x02,0x02,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*T*/
-		0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0xFE,0xFE,0x00,0x00,
-		0x00,0x07,0x0F,0x18,0x10,0x10,0x10,0x18,0x0F,0x07,0x00,0x00,/*U*/
-		0x00,0x0E,0x7E,0xE0,0x00,0x00,0x00,0xE0,0x7C,0x0E,0x00,0x00,
-		0x00,0x00,0x00,0x03,0x1F,0x18,0x1F,0x03,0x00,0x00,0x00,0x00,/*V*/
-		0x00,0x7E,0xFE,0x00,0x00,0xE0,0xE0,0x00,0x00,0xFE,0x7E,0x00,
-		0x00,0x00,0x1F,0x18,0x0F,0x01,0x01,0x0F,0x18,0x1F,0x00,0x00,/*W*/
-		0x00,0x02,0x06,0x1C,0x38,0xE0,0xE0,0x38,0x1C,0x06,0x02,0x00,
-		0x00,0x10,0x18,0x0E,0x07,0x01,0x01,0x07,0x0E,0x18,0x10,0x00,/*X*/
-		0x00,0x02,0x0E,0x3C,0xF0,0xC0,0xC0,0xF0,0x3C,0x0E,0x02,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,/*Y*/
-		0x00,0x02,0x02,0x02,0xC2,0xE2,0x3A,0x0E,0x02,0x00,0x00,0x00,
-		0x00,0x10,0x1C,0x17,0x11,0x10,0x10,0x10,0x10,0x00,0x00,0x00,/*Z*/
-		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/* */
+		0x00,0xF8,0xFE,0x06,0x03,0x83,0xC3,0x63,0x33,0x1E,0xFE,0xF8,0x00,0x07,0x1F,0x1E,0x33,0x31,0x30,0x30,0x30,0x18,0x1F,0x07,//0
+		0x00,0x00,0x00,0x0C,0x0C,0x0E,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x30,0x3F,0x3F,0x30,0x30,0x30,0x00,//1
+		0x00,0x1C,0x1E,0x07,0x03,0x03,0x83,0xC3,0xE3,0x77,0x3E,0x1C,0x00,0x30,0x38,0x3C,0x3E,0x37,0x33,0x31,0x30,0x30,0x30,0x30,//2
+		0x00,0x0C,0x0E,0x07,0xC3,0xC3,0xC3,0xC3,0xC3,0xE7,0x7E,0x3C,0x00,0x0C,0x1C,0x38,0x30,0x30,0x30,0x30,0x30,0x39,0x1F,0x0E,//3
+		0x00,0xC0,0xE0,0x70,0x38,0x1C,0x0E,0x07,0xFF,0xFF,0x00,0x00,0x00,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x3F,0x3F,0x03,0x03,//4
+		0x00,0x3F,0x7F,0x63,0x63,0x63,0x63,0x63,0x63,0xE3,0xC3,0x83,0x00,0x0C,0x1C,0x38,0x30,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,//5
+		0x00,0xC0,0xF0,0xF8,0xDC,0xCE,0xC7,0xC3,0xC3,0xC3,0x80,0x00,0x00,0x0F,0x1F,0x39,0x30,0x30,0x30,0x30,0x30,0x39,0x1F,0x0F,//6
+		0x00,0x03,0x03,0x03,0x03,0x03,0x03,0xC3,0xF3,0x3F,0x0F,0x03,0x00,0x00,0x00,0x00,0x30,0x3C,0x0F,0x03,0x00,0x00,0x00,0x00,//7
+		0x00,0x00,0xBC,0xFE,0xE7,0xC3,0xC3,0xC3,0xE7,0xFE,0xBC,0x00,0x00,0x0F,0x1F,0x39,0x30,0x30,0x30,0x30,0x30,0x39,0x1F,0x0F,//8
+		0x00,0x3C,0x7E,0xE7,0xC3,0xC3,0xC3,0xC3,0xC3,0xE7,0xFE,0xFC,0x00,0x00,0x00,0x30,0x30,0x30,0x38,0x1C,0x0E,0x07,0x03,0x00,//9
+		0x00,0x00,0x00,0x00,0x70,0x70,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x1C,0x1C,0x00,0x00,0x00,0x00,0x00,//:
+		0x00,0x00,0x00,0x00,0x70,0x70,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9C,0xFC,0x7C,0x00,0x00,0x00,0x00,0x00,//;
+		0x00,0x00,0xC0,0xE0,0xF0,0x38,0x1C,0x0E,0x07,0x03,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0E,0x1C,0x38,0x30,0x00,0x00,//<
+		0x00,0x00,0x60,0x60,0x60,0x60,0x60,0x60,0x60,0x60,0x60,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x00,//=
+		0x00,0x00,0x03,0x07,0x0E,0x1C,0x38,0xF0,0xE0,0xC0,0x00,0x00,0x00,0x00,0x30,0x38,0x1C,0x0E,0x07,0x03,0x01,0x00,0x00,0x00,//>
+		0x00,0x1C,0x1E,0x07,0x03,0x83,0xC3,0xE3,0x77,0x3E,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x37,0x37,0x00,0x00,0x00,0x00,0x00,//?

-		0x00,0x60,0xF0,0x98,0x0C,0x06,0x02,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x01,0x03,0x06,0x04,0x00,0x00,0x00,0x00,0x00,/*<*/
-		0x00,0x02,0x06,0x0C,0x98,0xF0,0x60,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x04,0x06,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*>*/
+		0x00,0xF8,0xFE,0x07,0xF3,0xFB,0x1B,0xFB,0xFB,0x07,0xFE,0xF8,0x00,0x0F,0x1F,0x18,0x33,0x37,0x36,0x37,0x37,0x36,0x03,0x01,//@
+		0x00,0x00,0x00,0xE0,0xFC,0x1F,0x1F,0xFC,0xE0,0x00,0x00,0x00,0x00,0x38,0x3F,0x07,0x06,0x06,0x06,0x06,0x07,0x3F,0x38,0x00,//A
+		0x00,0xFF,0xFF,0xC3,0xC3,0xC3,0xC3,0xE7,0xFE,0xBC,0x00,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x30,0x39,0x1F,0x0F,0x00,//B
+		0x00,0xF0,0xFC,0x0E,0x07,0x03,0x03,0x03,0x07,0x0E,0x0C,0x00,0x00,0x03,0x0F,0x1C,0x38,0x30,0x30,0x30,0x38,0x1C,0x0C,0x00,//C
+		0x00,0xFF,0xFF,0x03,0x03,0x03,0x03,0x07,0x0E,0xFC,0xF0,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x38,0x1C,0x0F,0x03,0x00,//D
+		0x00,0xFF,0xFF,0xC3,0xC3,0xC3,0xC3,0xC3,0xC3,0x03,0x03,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x00,//E
+		0x00,0xFF,0xFF,0xC3,0xC3,0xC3,0xC3,0xC3,0xC3,0x03,0x03,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//F
+		0x00,0xF0,0xFC,0x0E,0x07,0x03,0xC3,0xC3,0xC3,0xC7,0xC6,0x00,0x00,0x03,0x0F,0x1C,0x38,0x30,0x30,0x30,0x30,0x3F,0x3F,0x00,//G
+		0x00,0xFF,0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xFF,0xFF,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,//H
+		0x00,0x00,0x00,0x03,0x03,0xFF,0xFF,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//I
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x0E,0x1E,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x07,0x00,//J
+		0x00,0xFF,0xFF,0xC0,0xE0,0xF0,0x38,0x1C,0x0E,0x07,0x03,0x00,0x00,0x3F,0x3F,0x00,0x01,0x03,0x07,0x0E,0x1C,0x38,0x30,0x00,//K
+		0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x00,//L
+		0x00,0xFF,0xFF,0x1E,0x78,0xE0,0xE0,0x78,0x1E,0xFF,0xFF,0x00,0x00,0x3F,0x3F,0x00,0x00,0x01,0x01,0x00,0x00,0x3F,0x3F,0x00,//M
+		0x00,0xFF,0xFF,0x0E,0x38,0xF0,0xC0,0x00,0x00,0xFF,0xFF,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x03,0x07,0x1C,0x3F,0x3F,0x00,//N
+		0x00,0xF0,0xFC,0x0E,0x07,0x03,0x03,0x07,0x0E,0xFC,0xF0,0x00,0x00,0x03,0x0F,0x1C,0x38,0x30,0x30,0x38,0x1C,0x0F,0x03,0x00,//O
+
+		0x00,0xFF,0xFF,0x83,0x83,0x83,0x83,0x83,0xC7,0xFE,0x7C,0x00,0x00,0x3F,0x3F,0x01,0x01,0x01,0x01,0x01,0x01,0x00,0x00,0x00,//P
+		0x00,0xF0,0xFC,0x0E,0x07,0x03,0x03,0x07,0x0E,0xFC,0xF0,0x00,0x00,0x03,0x0F,0x1C,0x38,0x30,0x36,0x3E,0x1C,0x3F,0x33,0x00,//Q
+		0x00,0xFF,0xFF,0x83,0x83,0x83,0x83,0x83,0xC7,0xFE,0x7C,0x00,0x00,0x3F,0x3F,0x01,0x01,0x03,0x07,0x0F,0x1D,0x38,0x30,0x00,//R
+		0x00,0x3C,0x7E,0xE7,0xC3,0xC3,0xC3,0xC3,0xC7,0x8E,0x0C,0x00,0x00,0x0C,0x1C,0x38,0x30,0x30,0x30,0x30,0x39,0x1F,0x0F,0x00,//S
+		0x00,0x00,0x03,0x03,0x03,0xFF,0xFF,0x03,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,//T
+		0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x07,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x07,0x00,//U
+		0x00,0x07,0x3F,0xF8,0xC0,0x00,0x00,0xC0,0xF8,0x3F,0x07,0x00,0x00,0x00,0x00,0x01,0x0F,0x3E,0x3E,0x0F,0x01,0x00,0x00,0x00,//V
+		0x00,0xFF,0xFF,0x00,0x00,0x80,0x80,0x00,0x00,0xFF,0xFF,0x00,0x00,0x3F,0x3F,0x1C,0x06,0x03,0x03,0x06,0x1C,0x3F,0x3F,0x00,//W
+		0x00,0x03,0x0F,0x1C,0x30,0xE0,0xE0,0x30,0x1C,0x0F,0x03,0x00,0x00,0x30,0x3C,0x0E,0x03,0x01,0x01,0x03,0x0E,0x3C,0x30,0x00,//X
+		0x00,0x03,0x0F,0x3C,0xF0,0xC0,0xC0,0xF0,0x3C,0x0F,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,//Y
+		0x00,0x03,0x03,0x03,0x03,0xC3,0xE3,0x33,0x1F,0x0F,0x03,0x00,0x00,0x30,0x3C,0x3E,0x33,0x31,0x30,0x30,0x30,0x30,0x30,0x00,//Z
+		0x00,0x00,0x00,0xFF,0xFF,0x03,0x03,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x00,0x00,0x00,// [
+		0x00,0x0E,0x1C,0x38,0x70,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0E,0x1C,0x18,// backslash
+		0x00,0x00,0x00,0x03,0x03,0x03,0x03,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x30,0x30,0x3F,0x3F,0x00,0x00,0x00,// ]
+		0x00,0x60,0x70,0x38,0x1C,0x0E,0x07,0x0E,0x1C,0x38,0x70,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,//_
+
+		0x00,0x00,0x00,0x00,0x00,0x3E,0x7E,0x4E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//`
+		0x00,0x00,0x40,0x60,0x60,0x60,0x60,0x60,0x60,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//a
+		0x00,0xFF,0xFF,0xC0,0x60,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//b
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0x60,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x30,0x18,0x08,0x00,//c
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0xE0,0xC0,0xFF,0xFF,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x30,0x3F,0x3F,0x00,//d
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0x60,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x3B,0x33,0x33,0x33,0x33,0x33,0x13,0x01,0x00,//e
+		0x00,0xC0,0xC0,0xFC,0xFE,0xC7,0xC3,0xC3,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//f
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0x60,0xE0,0xE0,0x00,0x00,0x03,0xC7,0xCE,0xCC,0xCC,0xCC,0xCC,0xE6,0x7F,0x3F,0x00,//g
+		0x00,0xFF,0xFF,0xC0,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,//h
+		0x00,0x00,0x00,0x00,0x60,0xEC,0xEC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//i
+		0x00,0x00,0x00,0x00,0x00,0x00,0x60,0xEC,0xEC,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0xE0,0xC0,0xC0,0xFF,0x7F,0x00,0x00,0x00,//j
+		0x00,0x00,0xFF,0xFF,0x00,0x80,0xC0,0xE0,0x60,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x03,0x07,0x0F,0x1C,0x38,0x30,0x00,0x00,//k
+		0x00,0x00,0x00,0x00,0x03,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//l
+		0x00,0xE0,0xC0,0xE0,0xE0,0xC0,0xC0,0xE0,0xE0,0xC0,0x80,0x00,0x00,0x3F,0x3F,0x00,0x00,0x3F,0x3F,0x00,0x00,0x3F,0x3F,0x00,//m
+		0x00,0x00,0xE0,0xE0,0x60,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,//n
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//o
+
+		0x00,0xE0,0xE0,0x60,0x60,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0xFF,0xFF,0x0C,0x18,0x18,0x18,0x18,0x1C,0x0F,0x07,0x00,//p
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0x60,0xE0,0xE0,0x00,0x00,0x07,0x0F,0x1C,0x18,0x18,0x18,0x18,0x0C,0xFF,0xFF,0x00,//q
+		0x00,0x00,0xE0,0xE0,0xC0,0x60,0x60,0x60,0x60,0xE0,0xC0,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//r
+		0x00,0xC0,0xE0,0x60,0x60,0x60,0x60,0x60,0x40,0x00,0x00,0x00,0x00,0x11,0x33,0x33,0x33,0x33,0x33,0x3F,0x1E,0x00,0x00,0x00,//s
+		0x00,0x60,0x60,0xFE,0xFE,0x60,0x60,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x3F,0x30,0x30,0x30,0x30,0x00,0x00,0x00,//t
+		0x00,0xE0,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x18,0x3F,0x3F,0x00,//u
+		0x00,0x60,0xE0,0x80,0x00,0x00,0x00,0x00,0x80,0xE0,0x60,0x00,0x00,0x00,0x01,0x07,0x1E,0x38,0x38,0x1E,0x07,0x01,0x00,0x00,//v
+		0x00,0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x07,0x1F,0x38,0x1C,0x0F,0x0F,0x1C,0x38,0x1F,0x07,0x00,//w
+		0x00,0x60,0xE0,0xC0,0x80,0x00,0x80,0xC0,0xE0,0x60,0x00,0x00,0x00,0x30,0x38,0x1D,0x0F,0x07,0x0F,0x1D,0x38,0x30,0x00,0x00,//x
+		0x00,0x00,0x60,0xE0,0x80,0x00,0x00,0x80,0xE0,0x60,0x00,0x00,0x00,0x00,0x00,0x81,0xE7,0x7E,0x1E,0x07,0x01,0x00,0x00,0x00,//y
+		0x00,0x60,0x60,0x60,0x60,0x60,0xE0,0xE0,0x60,0x20,0x00,0x00,0x00,0x30,0x38,0x3C,0x36,0x33,0x31,0x30,0x30,0x30,0x00,0x00,//z
+		0x00,0x00,0x80,0xC0,0xFC,0x7E,0x07,0x03,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x01,0x1F,0x3F,0x70,0x60,0x60,0x60,0x00,0x00,//{
+		0x00,0x00,0x00,0x00,0x00,0xBF,0xBF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,//|
+		0x00,0x00,0x03,0x03,0x03,0x07,0x7E,0xFC,0xC0,0x80,0x00,0x00,0x00,0x00,0x60,0x60,0x60,0x70,0x3F,0x1F,0x01,0x00,0x00,0x00,//}
+		0x00,0x10,0x18,0x0C,0x04,0x0C,0x18,0x10,0x18,0x0C,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~
+		0x00,0x00,0x80,0xC0,0x60,0x30,0x30,0x60,0xC0,0x80,0x00,0x00,0x00,0x0F,0x0F,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0F,0x0F,0x00,//Up triangle
+};
+		/*Start extended range*/
+		const uint8_t FontLatin2[] = {
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//A0 (blank)
+		0x00,0x00,0x00,0x00,0x80,0xF3,0xF3,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x3F,0x3F,0x0F,0x00,0x00,0x00,0x00,//A1//161
+		0x00,0x00,0xE0,0xF0,0x38,0xFE,0xFE,0x18,0x38,0x30,0x00,0x00,0x00,0x00,0x03,0x07,0x0E,0x3F,0x3F,0x0C,0x0E,0x06,0x00,0x00,//A2//162
+		0x00,0x00,0x00,0x80,0xF8,0xFC,0x8C,0x8C,0x1C,0x18,0x00,0x00,0x00,0x00,0x18,0x1C,0x1F,0x0B,0x18,0x18,0x18,0x18,0x08,0x00,//A3//163
+		0x00,0xF6,0xFE,0x18,0x0C,0x0C,0x0C,0x0C,0x18,0xFE,0xF6,0x00,0x00,0x1B,0x1F,0x06,0x0C,0x0C,0x0C,0x0C,0x06,0x1F,0x1B,0x00,//A4//164
+		0x00,0x03,0x0F,0x3C,0xF0,0xC0,0xC0,0xF0,0x3C,0x0F,0x03,0x00,0x00,0x00,0x0A,0x0A,0x0A,0x3F,0x3F,0x0A,0x0A,0x0A,0x00,0x00,//A5//165
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//A6 (blank)
+		0x00,0x00,0xDC,0xFE,0x22,0x22,0x22,0x22,0xE6,0xC4,0x00,0x00,0x00,0x00,0x08,0x19,0x11,0x11,0x11,0x11,0x1F,0x0E,0x00,0x00,//A7//167
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//A8 (blank)
+		0x00,0xF0,0xF8,0x1C,0xCC,0xEC,0x2C,0x6C,0x4C,0x1C,0xF8,0xF0,0x00,0x07,0x0F,0x1C,0x19,0x1B,0x1A,0x1B,0x19,0x1C,0x0F,0x07,//A9//169
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//AA (blank)
+		0x00,0x80,0xC0,0x60,0x20,0x00,0x80,0xC0,0x60,0x20,0x00,0x00,0x00,0x00,0x01,0x03,0x02,0x00,0x00,0x01,0x03,0x02,0x00,0x00,//AB//171
+		0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0xF8,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x03,0x00,//AC//172
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//AD (blank)
+		0x00,0xF0,0xF8,0x1C,0xEC,0xEC,0xAC,0xEC,0x4C,0x1C,0xF8,0xF0,0x00,0x07,0x0F,0x1C,0x1B,0x1B,0x18,0x1B,0x1B,0x1C,0x0F,0x07,//AE//174
+		0x00,0x00,0x00,0x00,0x00,0x0C,0x0C,0x0C,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//AF//175
+		0x00,0x00,0x00,0x1E,0x3F,0x33,0x33,0x3F,0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B0//176
+		0x00,0x00,0x00,0xC0,0xC0,0xF0,0xF0,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x1B,0x1B,0x18,0x18,0x00,0x00,0x00,//B1//177
+		0x00,0x00,0x19,0x1D,0x15,0x17,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B2//178
+		0x00,0x00,0x11,0x15,0x15,0x1F,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B3//179
+		0x00,0x00,0x00,0x00,0x04,0x06,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B4//180
+		0x00,0xF0,0xF0,0x00,0x00,0x00,0x00,0x00,0xF0,0xF0,0x00,0x00,0x00,0xFF,0xFF,0x0E,0x0C,0x0C,0x0C,0x06,0x0F,0x0F,0x00,0x00,//B5//181
+		0x00,0x38,0x7C,0xC6,0x82,0xFE,0xFE,0x02,0xFE,0xFE,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x3F,0x3F,0x00,0x00,//B6//182
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B7 (blank)
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B8 (blank)
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//B9 (blank)
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//BA (blank)
+		0x00,0x20,0x60,0xC0,0x80,0x00,0x20,0x60,0xC0,0x80,0x00,0x00,0x00,0x02,0x03,0x01,0x00,0x00,0x02,0x03,0x01,0x00,0x00,0x00,//BB//187
+		0x00,0x48,0x7C,0x7C,0x40,0x80,0xC0,0x60,0x30,0x10,0x00,0x00,0x00,0x00,0x04,0x06,0x03,0x01,0x06,0x07,0x04,0x1F,0x1F,0x00,//BC//188
+		0x00,0x48,0x7C,0x7C,0x40,0x80,0xC0,0x60,0x30,0x10,0x00,0x00,0x00,0x00,0x04,0x06,0x03,0x01,0x00,0x19,0x1D,0x17,0x12,0x00,//BD//189
+		0x00,0x44,0x54,0x7C,0x28,0x80,0xC0,0x60,0x30,0x10,0x00,0x00,0x00,0x00,0x04,0x06,0x03,0x01,0x06,0x07,0x04,0x1F,0x1F,0x00,//BE//190
+		0x00,0x00,0x00,0x80,0xC0,0xFB,0x7B,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x1F,0x3B,0x31,0x30,0x30,0x30,0x38,0x1E,0x0E,0x00,//BF//191
+		0x00,0x00,0x00,0x80,0xE1,0x7B,0x7E,0xE4,0x80,0x00,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C0//192
+		0x00,0x00,0x00,0x80,0xE4,0x7E,0x7B,0xE1,0x80,0x00,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C1//193
+		0x00,0x00,0x00,0x84,0xE6,0x7B,0x7B,0xE6,0x84,0x00,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C2//194
+		0x00,0x00,0x00,0x82,0xE3,0x79,0x7B,0xE2,0x83,0x01,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C3//195
+		0x00,0x00,0x00,0x83,0xE3,0x78,0x78,0xE3,0x83,0x00,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C4//196
+		0x00,0x00,0x00,0x80,0xE2,0x75,0x75,0xE2,0x80,0x00,0x00,0x00,0x00,0x38,0x3E,0x0F,0x0D,0x0C,0x0C,0x0D,0x0F,0x3E,0x38,0x00,//C5//197
+		0x00,0x00,0x80,0xF0,0x7C,0x1F,0xFF,0xFF,0xC3,0xC3,0x03,0x00,0x00,0x3C,0x3F,0x07,0x06,0x06,0x3F,0x3F,0x30,0x30,0x30,0x00,//C6//198
+		0x00,0xF0,0xFC,0x0E,0x07,0x03,0x03,0x03,0x07,0x1E,0x1C,0x00,0x00,0x01,0x07,0xCE,0xDC,0xF8,0xF8,0x18,0x1C,0x0E,0x06,0x00,//C7//199
+		0x00,0xF8,0xF8,0x99,0x9B,0x9E,0x9C,0x98,0x98,0x18,0x18,0x00,0x00,0x3F,0x3F,0x31,0x31,0x31,0x31,0x31,0x31,0x30,0x30,0x00,//C8//200
+		0x00,0xF8,0xF8,0x98,0x98,0x9C,0x9E,0x9B,0x99,0x18,0x18,0x00,0x00,0x3F,0x3F,0x31,0x31,0x31,0x31,0x31,0x31,0x30,0x30,0x00,//C9//201
+		0x00,0xF8,0xF8,0x9C,0x9E,0x9B,0x9B,0x9E,0x9C,0x18,0x18,0x00,0x00,0x3F,0x3F,0x31,0x31,0x31,0x31,0x31,0x31,0x30,0x30,0x00,//CA//202
+		0x00,0xF8,0xF8,0x9B,0x9B,0x98,0x98,0x9B,0x9B,0x18,0x18,0x00,0x00,0x3F,0x3F,0x31,0x31,0x31,0x31,0x31,0x31,0x30,0x30,0x00,//CB//203
+		0x00,0x00,0x00,0x19,0x1B,0xFE,0xFC,0x18,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//CC//204
+		0x00,0x00,0x00,0x18,0x18,0xFC,0xFE,0x1B,0x19,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//CD//205
+		0x00,0x00,0x00,0x1C,0x1E,0xFB,0xFB,0x1E,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//CE//206
+		0x00,0x00,0x00,0x1B,0x1B,0xF8,0xF8,0x1B,0x1B,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//CF//207
+		0x00,0xC0,0xFF,0xFF,0xC3,0x03,0x03,0x07,0x0E,0xFC,0xF0,0x00,0x00,0x00,0x3F,0x3F,0x30,0x30,0x30,0x38,0x1C,0x0F,0x03,0x00,//D0//208
+		0x00,0xF8,0xF8,0x72,0xE3,0xC1,0x83,0x02,0x03,0xF9,0xF8,0x00,0x00,0x3F,0x3F,0x00,0x00,0x01,0x03,0x07,0x0E,0x3F,0x3F,0x00,//D1//209
+		0x00,0xE0,0xF0,0x39,0x1B,0x1E,0x1C,0x18,0x38,0xF0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//D2//210
+		0x00,0xE0,0xF0,0x38,0x18,0x1C,0x1E,0x1B,0x39,0xF0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//D3//211
+		0x00,0xE0,0xF0,0x3C,0x1E,0x1B,0x1B,0x1E,0x3C,0xF0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//D4//212
+		0x00,0xE0,0xF0,0x3A,0x1B,0x19,0x1B,0x1A,0x3B,0xF1,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//D5//213
+		0x00,0xE0,0xF0,0x3B,0x1B,0x18,0x18,0x1B,0x3B,0xF0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//D6//214
+		0x00,0x00,0x10,0x30,0x60,0xC0,0xC0,0x60,0x30,0x10,0x00,0x00,0x00,0x00,0x04,0x06,0x03,0x01,0x01,0x03,0x06,0x04,0x00,0x00,//D7//215
+		0x00,0xF0,0xF8,0x1C,0x0C,0x8C,0xEC,0x7C,0x18,0xFC,0xF4,0x00,0x00,0x2F,0x3F,0x18,0x3E,0x37,0x31,0x30,0x38,0x1F,0x0F,0x00,//D8//216
+		0x00,0xF8,0xF8,0x01,0x03,0x06,0x04,0x00,0x00,0xF8,0xF8,0x00,0x00,0x07,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x07,0x00,//D9//217
+		0x00,0xF8,0xF8,0x00,0x00,0x04,0x06,0x03,0x01,0xF8,0xF8,0x00,0x00,0x07,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x07,0x00,//DA//218
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//DB (blank)
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//DC (blank)
+		0x00,0x08,0x18,0x30,0x60,0xC4,0xC6,0x63,0x31,0x18,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,//DD//221
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//DE (blank)
+		0x00,0x00,0xC0,0xE0,0x30,0x10,0x10,0x30,0xE0,0xC0,0x00,0x00,0x00,0x00,0xFF,0xFF,0x21,0x21,0x21,0x33,0x3F,0x1E,0x00,0x00,//DF//223
+		0x00,0x00,0x40,0x60,0x62,0x66,0x6C,0x68,0x60,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E0//224
+		0x00,0x00,0x40,0x60,0x68,0x6C,0x66,0x62,0x60,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E1//225
+		0x00,0x00,0x40,0x68,0x6C,0x66,0x66,0x6C,0x68,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E2//226
+		0x00,0x00,0x40,0x68,0x6C,0x64,0x6C,0x68,0x6C,0xE4,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E3//227
+		0x00,0x00,0x40,0x6C,0x6C,0x60,0x60,0x6C,0x6C,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E4//228
+		0x00,0x00,0x40,0x60,0x64,0x6A,0x6A,0x64,0x60,0xE0,0xC0,0x00,0x00,0x1C,0x3E,0x33,0x33,0x33,0x33,0x33,0x33,0x3F,0x3F,0x00,//E5//229
+		0x00,0x80,0xC0,0x40,0x40,0xC0,0x80,0x40,0x40,0xC0,0x80,0x00,0x00,0x1C,0x3E,0x22,0x22,0x1F,0x3F,0x22,0x22,0x33,0x11,0x00,//E6//230
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0x60,0xE0,0xC0,0x80,0x00,0x00,0x0F,0x1F,0xB8,0xB0,0xF0,0xF0,0x30,0x38,0x18,0x08,0x00,//E7//231
+		0x00,0x80,0xC0,0xE0,0x62,0x66,0x6C,0x68,0x60,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x33,0x33,0x33,0x33,0x33,0x33,0x13,0x03,0x00,//E8//232
+		0x00,0x80,0xC0,0xE0,0x60,0x68,0x6C,0x66,0x62,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x3B,0x33,0x33,0x33,0x33,0x33,0x13,0x03,0x00,//E9//233
+		0x00,0x80,0xC0,0xE8,0x6C,0x66,0x66,0x6C,0x68,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x33,0x33,0x33,0x33,0x33,0x33,0x13,0x03,0x00,//EA//234
+		0x00,0x80,0xC0,0xEC,0x6C,0x60,0x60,0x6C,0x6C,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x33,0x33,0x33,0x33,0x33,0x33,0x13,0x03,0x00,//EB//235
+		0x00,0x00,0x00,0x00,0x62,0xE6,0xEC,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//EC//236
+		0x00,0x00,0x00,0x00,0x68,0xEC,0xE6,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//ED//237
+		0x00,0x00,0x00,0x08,0x6C,0xE6,0xE6,0x0C,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//EE//238
+		0x00,0x00,0x00,0x0C,0x6C,0xE0,0xEC,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x3F,0x3F,0x30,0x30,0x00,0x00,0x00,//EF//239
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//F0 (blank)
+		0x00,0x00,0xE0,0xE8,0x6C,0x64,0x6C,0x68,0xEC,0xC4,0x80,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,//F1//241
+		0x00,0x80,0xC0,0xE0,0x62,0x66,0x6C,0x68,0xE0,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//F2//242
+		0x00,0x80,0xC0,0xE0,0x68,0x6C,0x66,0x62,0xE0,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//F3//243
+		0x00,0x80,0xC0,0xE8,0x6C,0x66,0x66,0x6C,0xE8,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//F4//244
+		0x00,0x80,0xC8,0xEC,0x64,0x6C,0x68,0x6C,0xE4,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//F5//245
+		0x00,0x80,0xC0,0xEC,0x6C,0x60,0x60,0x6C,0xEC,0xC0,0x80,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x38,0x1F,0x0F,0x00,//F6//246
+		0x00,0x00,0x80,0x80,0x80,0xB0,0xB0,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x0D,0x0D,0x01,0x01,0x01,0x00,0x00,//F7//247
+		0x00,0x80,0xC0,0xE0,0x60,0x60,0x60,0xE0,0xC0,0xE0,0xA0,0x00,0x00,0x2F,0x3F,0x18,0x3C,0x36,0x33,0x31,0x38,0x1F,0x0F,0x00,//F8//248
+		0x00,0xE0,0xE0,0x00,0x02,0x06,0x0C,0x08,0x00,0xE0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x18,0x3F,0x3F,0x00,//F9//249
+		0x00,0xE0,0xE0,0x00,0x08,0x0C,0x06,0x02,0x00,0xE0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x18,0x3F,0x3F,0x00,//FA//250
+		0x00,0xE0,0xE0,0x08,0x0C,0x06,0x06,0x0C,0x08,0xE0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x18,0x3F,0x3F,0x00,//FB//251
+		0x00,0xE0,0xE0,0x0C,0x0C,0x00,0x00,0x0C,0x0C,0xE0,0xE0,0x00,0x00,0x0F,0x1F,0x38,0x30,0x30,0x30,0x30,0x18,0x3F,0x3F,0x00,//FC//252
+		0x00,0x00,0x60,0xE0,0x80,0x10,0x18,0x8C,0xE4,0x60,0x00,0x00,0x00,0x00,0x00,0x81,0xE7,0x7E,0x1E,0x07,0x01,0x00,0x00,0x00,//FD//253
+		0x00,0x00,0x03,0xFF,0xFF,0x1B,0x18,0x18,0xF8,0xF0,0x00,0x00,0x00,0x00,0x30,0x3F,0x3F,0x36,0x06,0x06,0x07,0x03,0x00,0x00,//FE//254
+		0x00,0x00,0x60,0xEC,0x8C,0x00,0x00,0x8C,0xEC,0x60,0x00,0x00,0x00,0x00,0x00,0x81,0xE7,0x7E,0x1E,0x07,0x01,0x00,0x00,0x00,//FF//255

-		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-		0x00,0x00,0x00,0x00,0x0F,0x0F,0x0F,0x0F,0x00,0x00,0x00,0x00,/*.*/

 };
-const uint8_t extendedFont[] = {
+const uint8_t ExtraFontChars[] = {
+		0x00,0x0C,0x12,0x12,0x0C,0x00,0xF8,0x08,0x08,0x08,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x01,0x01,0x01,0x00,0x00,//Degrees F
+		0x00,0x0C,0x12,0x12,0x0C,0xE0,0x10,0x08,0x08,0x08,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x04,0x08,0x08,0x08,0x08,0x00, // Degrees C
+		0x00,0x00,0x00,0x10,0x18,0x1C,0xFE,0x1C,0x18,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00,//UP arrow
+		/*
+		0x00,0x00,0x00,0x80,0x80,0xFE,0xFF,0x83,0x87,0x06,0x00,0x00,0x00,0x00,0x30,0x70,0x60,0x7F,0x3F,0x00,0x00,0x00,0x00,0x00,//Function?
+		0x00,0x70,0xFA,0xDB,0xDB,0xDB,0xDB,0xDB,0xDB,0xFF,0xFE,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x00,0x00,//a_
+		0x00,0x3C,0x7E,0xE7,0xC3,0xC3,0xC3,0xC3,0xE7,0x7E,0x3C,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x00,0x00,//0_
+		0x55,0x00,0xAA,0x00,0x55,0x00,0xAA,0x00,0x55,0x00,0xAA,0x00,0x55,0x00,0xAA,0x00,0x55,0x00,0xAA,0x00,0x55,0x00,0xAA,0x00,//25%  block
+		0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,//50% pipe
+		0xAA,0xFF,0x55,0xFF,0xAA,0xFF,0x55,0xFF,0xAA,0xFF,0x55,0xFF,0xAA,0xFF,0x55,0xFF,0xAA,0xFF,0x55,0xFF,0xAA,0xFF,0x55,0xFF,//75% block
+		0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,//| pipe
+		0x80,0x80,0x80,0x80,0x80,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,//T pipe ,|
+		0xC0,0xC0,0xFF,0xFF,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0xFE,0xFE,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,//,| double pipe
+		0x00,0x00,0xFF,0xFF,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,// || double pipe
+		0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0xFE,0xFE,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,//#NAME?//#NAME?
+		0xC0,0xC0,0xFF,0xFF,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x07,0x07,0x00,0x00,0x00,0x00,0x00,//,^ double pupe
+		0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,//#NAME?//#NAME?
+		0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//,> pipe
+		0x80,0x80,0x80,0x80,0x80,0xFF,0xFF,0x80,0x80,0x80,0x80,0x80,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//_|_ pipe
+		0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x01,0x01,0x01,0x01,0x01,0xFF,0xFF,0x01,0x01,0x01,0x01,0x01,//,|, pipe
+		0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x01,0x01,0x01,0x01,0x01,//|, pipe
+		0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//#NAME?//#NAME?
+		0x80,0x80,0x80,0x80,0x80,0xFF,0xFF,0x80,0x80,0x80,0x80,0x80,0x01,0x01,0x01,0x01,0x01,0xFF,0xFF,0x01,0x01,0x01,0x01,0x01,//#NAME?//#NAME?
+		0x00,0x00,0xFF,0xFF,0x00,0xFF,0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0x07,0x07,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,//,> double pipe
+		0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0xFF,0xFF,0x00,0xFE,0xFE,0x06,0x06,0x06,0x06,0x06,//^, double pipe
+		0xC0,0xC0,0xFF,0xFF,0x00,0xFF,0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,//_|_ double pipe
+		0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x06,0x06,0xFE,0xFE,0x00,0xFE,0xFE,0x06,0x06,0x06,0x06,0x06,//,|, double pipe
+		0x00,0x00,0xFF,0xFF,0x00,0xFF,0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0xFF,0xFF,0x00,0xFE,0xFE,0x06,0x06,0x06,0x06,0x06,//|, double pipe
+		0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,//== double pipe
+		0xC0,0xC0,0xFF,0xFF,0x00,0xFF,0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0x06,0x06,0xFE,0xFE,0x00,0xFE,0xFE,0x06,0x06,0x06,0x06,0x06,//#NAME?//#NAME?
+		0x00,0x00,0x00,0x78,0xFC,0xCC,0x8C,0x0C,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x3E,0x33,0x33,0x3F,0x1E,0x00,0x00,0x00,//Delta lowercase
+		0x00,0x00,0x00,0x00,0x00,0x7E,0x7E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//27 (')
+		0x80,0x80,0x80,0x80,0x80,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,//,^ pipe
+		0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x01,0x01,0x01,0x01,0x01,//| , pipe
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,//solid block
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,//half block bottom
+		0x00,0x00,0x00,0x00,0x00,0xBF,0xBF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,//7C (|)
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//top half solid block
+		0x00,0x00,0x0C,0xFC,0xFC,0x6C,0x60,0x60,0xE0,0xC0,0x00,0x00,0x00,0x00,0x30,0x3F,0x3F,0x36,0x06,0x06,0x07,0x03,0x00,0x00,//DE small
+		0x00,0x00,0x03,0xFF,0xFF,0x1B,0x18,0x18,0xF8,0xF0,0x00,0x00,0x00,0x00,0x30,0x3F,0x3F,0x36,0x06,0x06,0x07,0x03,0x00,0x00,//DE large
+		0x00,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//? (,)
+		0x00,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x06,0x00,0x00,0x00,//=
+		0x00,0x00,0x00,0x40,0x80,0x80,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//sideways comma
+		0x00,0x00,0x80,0xC0,0x80,0x00,0x00,0x80,0xC0,0x80,0x00,0x00,0x00,0x00,0x01,0x03,0x01,0x00,0x00,0x01,0x03,0x01,0x00,0x00,//..
+		0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x01,0x00,0x00,0x00,0x00,//.
+		0x00,0x00,0x02,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//tiny 1
+		0x00,0x00,0x00,0x00,0xF0,0xF0,0xF0,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x03,0x03,0x03,0x00,0x00,0x00,0x00,//small block
+		*/
+};
+const uint8_t FontSymbols[] = {
 		0x00,0x00,0xF8,0x08,0x0E,0x02,0x02,0x0E,0x08,0xF8,0x00,0x00,
 		0x00,0x00,0x7F,0x40,0x40,0x40,0x40,0x40,0x40,0x7F,0x00,0x00,/*Battery Empty*/

@@ -132,6 +300,113 @@ const uint8_t extendedFont[] = {

 		0x00,0x00,0xF8,0xF8,0xFE,0xF2,0xF2,0xFE,0xF8,0xF8,0x00,0x00,
 		0x00,0x00,0x7F,0x7F,0x7F,0x7F,0x7F,0x7F,0x7F,0x7F,0x00,0x00,/*Battery 10*/
+
+
+
+		0x00,0x00,0x00,0xFC,0xF8,0xF0,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x0F,0x07,0x03,0x01,0x00,0x00,0x00,0x00,//Right block
+		0x00,0x00,0x00,0x80,0xC0,0xE0,0xF0,0xF8,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0F,0x1F,0x00,0x00,0x00,//left block
+		0x00,0x00,0x00,0x10,0x18,0x1C,0xFE,0x1C,0x18,0x10,0x00,0x00,0x00,0x00,0x00,0x04,0x0C,0x1C,0x3F,0x1C,0x0C,0x04,0x00,0x00,//UD arrow
+		0x00,0x00,0x00,0xFE,0xFE,0x00,0x00,0xFE,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x37,0x37,0x00,0x00,0x37,0x37,0x00,0x00,0x00,//!!
+		0x00,0x38,0x7C,0xC6,0x82,0xFE,0xFE,0x02,0xFE,0xFE,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x00,0x3F,0x3F,0x00,0x00,//paragraph
+		0x00,0x00,0xDC,0xFE,0x22,0x22,0x22,0x22,0xE6,0xC4,0x00,0x00,0x00,0x00,0x08,0x19,0x11,0x11,0x11,0x11,0x1F,0x0E,0x00,0x00,//section
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x00,//cursor
+		0x00,0x00,0x00,0x08,0x0C,0x0E,0xFF,0x0E,0x0C,0x08,0x00,0x00,0x00,0x00,0x00,0x44,0x4C,0x5C,0x7F,0x5C,0x4C,0x44,0x00,0x00,//UD arrow
+		0x00,0x00,0x00,0x10,0x18,0x1C,0xFE,0x1C,0x18,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00,//UP arrow
+		0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x0C,0x1C,0x3F,0x1C,0x0C,0x04,0x00,0x00,//Down arrow
+		0x00,0x00,0x80,0x80,0x80,0x80,0x80,0xF0,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x03,0x01,0x00,0x00,//right arrow
+		0x00,0x00,0x80,0xC0,0xE0,0xF0,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x00,0x00,0x00,0x00,0x00,0x00,//left arrow
+		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x00,
+		0x00,0x80,0xC0,0xE0,0xF0,0x80,0x80,0x80,0xF0,0xE0,0xC0,0x80,0x00,0x00,0x01,0x03,0x07,0x00,0x00,0x00,0x07,0x03,0x01,0x00,//LR arrow
+		0x00,0x00,0x00,0x00,0x80,0xC0,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x04,0x06,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x06,0x04,//UP block
+		0x00,0x20,0x60,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0x60,0x20,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x03,0x01,0x00,0x00,0x00,//Down block
+};
+const uint8_t DoubleWidthChars[]={
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0xFF,/*Bar 0*/
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xC0,0x80,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xE0,0xC0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xF0,0xE0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xF8,0xF0,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFC,0xF8,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFE,0xFC,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFE,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,0xFE,0xFF,
+
+		0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0x81,0x01,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0x81,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xC1,0x81,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xC1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xE1,0xC1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xE1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xF1,0xE1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xF1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xF9,0xF1,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xF9,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFD,0xF9,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFD,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,0xFD,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
+		0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
 };
 const uint8_t Iron_Base[] ={
 		0x00,0x20,0x60,0x60,0x60,0x60,0x60,0x60,0x90,0x90,0x90,0x90,
--- a/workspace/ts100/inc/I2C.h
+++ b/workspace/ts100/inc/I2C.h
@@ -11,6 +11,7 @@

 void I2C_Configuration(void);
 void I2C_PageWrite(u8* pbuf, u8 numbyte, u8 deviceaddr);
-void I2C_PageRead(u8* pbuf, u8 numbyte, u8 deviceaddr, u8 readaddr);
+int I2C_Master_Read(uint8_t deviceAddr, uint8_t readAddr, uint8_t* pBuffer,
+		uint16_t numByteToRead);
 #endif
 /******************************** END OF FILE *********************************/
--- a/workspace/ts100/inc/Interrupt.h
+++ b/workspace/ts100/inc/Interrupt.h
@@ -8,41 +8,28 @@
 /* Functions for access to data */
 extern volatile uint32_t system_Ticks;
 void delayMs(uint32_t ticks);
-volatile extern uint32_t lastKeyPress;
-volatile extern uint32_t lastMovement;
+extern volatile uint32_t lastMovement;

-volatile extern uint8_t keyState;
-volatile extern uint8_t rawKeys;
+extern volatile uint8_t InterruptMask;//Used to mask interrupts

+extern volatile uint8_t rawKeys;
 inline uint32_t millis() {
 	return system_Ticks;
 }

-inline uint32_t getLastButtonPress() {
-	return lastKeyPress;
-}
-inline void resetLastButtonPress() {
-	lastKeyPress = millis();
-
-}
-inline void resetButtons() {
-	keyState = 0;
-}
-
 inline uint32_t getLastMovement() {
 	return lastMovement;
 }

-inline uint16_t getButtons() {
-	return keyState;
-}
+uint8_t getButtons();
+uint32_t getLastButtonPress();
 inline uint16_t getRawButtons() {
 	return rawKeys;
 }
-inline void restoreButtons()
-{
-	keyState=getRawButtons();
-}
+
+extern volatile uint8_t RotationChangedFlag;
+
+

 /*IRQ prototypes*/
 void NMI_Handler(void);
--- a/workspace/ts100/inc/MMA8652FC.h
+++ b/workspace/ts100/inc/MMA8652FC.h
@@ -14,9 +14,8 @@
 #ifndef __MMA8652FC__H
 #define __MMA8652FC__H

-
-void StartUp_Accelerometer(uint8_t sensitivity);//This is the only function we expose
-
+void StartUp_Accelerometer(uint8_t sensitivity); //This is the only function we expose
+uint8_t getOrientation();
 //--------------MMA8652 Device ID----------------------------------------------//

 #define DEVICE_ADDR     0X1D        
@@ -99,8 +98,6 @@ void StartUp_Accelerometer(uint8_t sensitivity);//This is the only function we e
 #define INT_SOURCE    0X0C
 #define DEVICE_ID     0X0D

-
-
 //-----STATUS_REG(0X00)-----Bit Define----------------------------------------//
 #define ZYXDR_BIT     0X08
 //----XYZ_DATA_CFG_REG(0xE)-Bit Define----------------------------------------//
@@ -123,7 +120,7 @@ void StartUp_Accelerometer(uint8_t sensitivity);//This is the only function we e
 //---------CTRL_REG2(0X2B)Bit Define------------------------------------------// 
 #define MODS_MASK     0x03     //Oversampling Mode 4 
 #define Normal_Mode   0x0      //Normal=0,Low Noise Low Power MODS=1,
-                               //HI RESOLUTION=2,LOW POWER MODS = 11 
+//HI RESOLUTION=2,LOW POWER MODS = 11
 //----CTRL_REG4---Interrupt Enable BIT ---------------------------------------//   
 //0 interrupt is disabled (default) 
 //1 interrupt is enabled     
--- a/workspace/ts100/inc/Modes.h
+++ b/workspace/ts100/inc/Modes.h
@@ -10,14 +10,18 @@

 #ifndef MODES_H_
 #define MODES_H_
+
 #include "Interrupt.h"
 #include "S100V0_1.h"
 #include "Oled.h"
 #include "PID.h"
 #include "Settings.h"
 #include "Analog.h"
+#include "MMA8652FC.h"
 #include <string.h>
-enum {
+#include "Strings.h"
+
+typedef enum {
 	STARTUP, 		//we are sitting on the prompt to push a button
 	SOLDERING, 		//Normal operating mode
 	TEMP_ADJ,		//Adjust the set temperature
@@ -29,10 +33,14 @@ enum {
 	DCINDISP,		//Disp the input voltage && Cal the DCin voltage divider
 	TEMPCAL,		//Cal tip temp offset

-} operatingMode;
-#define SETTINGSOPTIONSCOUNT 10 /*Number of settings in the settings menu*/
-
-enum {
+} operatingModeEnum;
+//#define PIDTUNING
+#ifdef PIDTUNING
+#define SETTINGSOPTIONSCOUNT (13+3) /*Number of settings in the settings menu*/
+#else
+#define SETTINGSOPTIONSCOUNT (13) /*Number of settings in the settings menu*/
+#endif
+typedef enum {
 	UVCO = 0,
 	SLEEP_TEMP,
 	SLEEP_TIME,
@@ -41,11 +49,20 @@ enum {
 	TEMPDISPLAY,
 	TEMPROUNDING,
 	DISPUPDATERATE,
-	LEFTY,
+	SCREENROTATION,
 	BOOSTMODE,
 	BOOSTTEMP,
-} settingsPage;
+	POWERDISPLAY,
+	AUTOSTART,
+	COOLINGBLINK,
+#ifdef PIDTUNING
+PIDP,
+PIDI,
+PIDD,
+#endif
+} settingsPageEnum;

 void ProcessUI();
 void DrawUI();
+extern operatingModeEnum operatingMode;
 #endif /* MODES_H_ */
--- a/workspace/ts100/inc/Oled.h
+++ b/workspace/ts100/inc/Oled.h
@@ -13,22 +13,26 @@

 void Oled_DisplayOn(void);
 void Oled_DisplayOff(void);
-
-const u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high,const u8* ptr);
+void OLED_Sync();
+void Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 height, const u8* ptr);
 void Set_ShowPos(u8 x, u8 y);
 void Oled_DisplayFlip();
+void OLED_InvertBuffer();
 void GPIO_Init_OLED(void);
 void Init_Oled(uint8_t leftHanded);
-const u8* Data_Command(u8 len,const u8* ptr);
-void Clear_Screen(void);//Clear the screen
+const u8* Data_Command(u8 len, const u8* ptr);
+void Clear_Screen(void); //Clear the screen
 /*Functions for writing to the screen*/
 void OLED_DrawString(const char* string, const uint8_t length);
-void OLED_DrawChar(char c, uint8_t x);
-void OLED_DrawExtendedChar(uint8_t id, uint8_t x);
+void OLED_DrawChar(char c, uint8_t x,char preCursor);
+void OLED_DrawExtraFontChars(uint8_t id, uint8_t x);
+void OLED_DrawSymbolChar(uint8_t id, uint8_t x);
+void OLED_DrawWideChar(uint8_t id, uint8_t x);
 void OLED_DrawTwoNumber(uint8_t in, uint8_t x);
-void OLED_BlankSlot(uint8_t xStart,uint8_t width);
 void OLED_DrawThreeNumber(uint16_t in, uint8_t x);
 void OLED_DrawIDLELogo();
-void OLED_DrawSymbol(uint8_t x,uint8_t symbol);
+void OLED_DrawSymbol(uint8_t x, uint8_t symbol);
+
+void OLED_SetOrientation(uint8_t ori);
+uint8_t OLED_GetOrientation();
 #endif
-/******************************** END OF FILE *********************************/
--- a/workspace/ts100/inc/PID.h
+++ b/workspace/ts100/inc/PID.h
@@ -12,10 +12,11 @@
 #include "Analog.h"
 #include "Interrupt.h"

-struct {
+typedef struct {
 	uint32_t kp, ki, kd; //PID values
-} pidSettings;
+} pidSettingsType;

 int32_t computePID(uint16_t setpoint);
 void setupPID(void);
+extern pidSettingsType pidSettings;
 #endif /* PID_H_ */
--- a/workspace/ts100/inc/Settings.h
+++ b/workspace/ts100/inc/Settings.h
@@ -11,7 +11,8 @@
 #define SETTINGS_H_
 #include <stdint.h>
 #include "stm32f10x_flash.h"
-#define SETTINGSVERSION 13 /*Change this if you change the struct below to prevent people getting out of sync*/
+#include "Oled.h"
+#define SETTINGSVERSION 17 /*Change this if you change the struct below to prevent people getting out of sync*/
 //Display Speeds
 #define DISPLAYMODE_FAST 	(0x00)
 #define DISPLAYMODE_MEDIUM 	(0x01)
@@ -24,23 +25,29 @@
 /*
 * This struct must be a multiple of 2 bytes as it is saved / restored from flash in uint16_t chunks
 */
-struct {
+typedef struct {
 	uint16_t SolderingTemp; 		//current set point for the iron
 	uint32_t SleepTemp; 			//temp to drop to in sleep
 	uint8_t version;				//Used to track if a reset is needed on firmware upgrade
 	uint8_t SleepTime; 				//minutes timeout to sleep
-	uint8_t cutoutSetting:5; 		//(3 bits) The voltage we cut out at for under voltage
+	uint8_t cutoutSetting:3; 		//(3 bits) The voltage we cut out at for under voltage
+	uint8_t powerDisplay:1;			//Toggle to swap the arrows with a power readout instead
 	uint8_t displayTempInF:1;		//If we need to convert the C reading to F
-	uint8_t flipDisplay:1;			//If true we want to invert the display for lefties
-	uint8_t sensitivity:6;			//Sensitivity of accelerometer (5 bits)
+	uint8_t OrientationMode:2;		//If true we want to invert the display for lefties
+	uint8_t sensitivity:5;			//Sensitivity of accelerometer (5 bits)
+	uint8_t autoStart:2;			//Should the unit automatically jump straight into soldering mode when power is applied
 	uint8_t ShutdownTime:6;			//Time until unit shuts down if left alone
 	uint8_t displayUpdateSpeed:2;	//How fast the display updates / temp showing mode
 	uint8_t temperatureRounding:2;	//Rounding mode for the temperature
 	uint8_t boostModeEnabled:1;		//Boost mode swaps BUT_A in soldering mode to temporary soldering temp over-ride
+	uint8_t coolingTempBlink:1;		//Should the temperature blink on the cool down screen until its <50C
 	uint16_t tempCalibration;		//Temperature calibration value
 	uint16_t voltageDiv;			//Voltage divisor factor
 	uint16_t BoostTemp; 			//Boost mode set point for the iron
-} systemSettings;
+	uint32_t padding;//This is here for in case we are not an even divisor so that nothing gets cut off
+} systemSettingsType;
+
+extern systemSettingsType systemSettings;

 void saveSettings();
 void restoreSettings();
--- a/workspace/ts100/inc/Strings.h
+++ b/workspace/ts100/inc/Strings.h
@@ -0,0 +1,31 @@
+/*
+ * Strings.h
+ *
+ *  Created on: 4Aug.,2017
+ *      Author: Ben V. Brown
+ */
+
+/*
+ * This file is used to allow for different language builds of the firmware
+ * This file houses all the strings for the text used on the iron.
+ */
+#ifndef STRINGS_H_
+#define STRINGS_H_
+
+extern const char* SettingsLongNames[14];
+extern const char* SettingsShortNames[14];
+extern const char* TempCalStatus[3]; //All fixed 8 chars
+extern const char* UVLOWarningString; //Fixed width 8 chars
+extern const char* CoolingPromptString; //Fixed width 5 chars
+extern const char SettingTrueChar;
+extern const char SettingFalseChar;
+extern const char SettingSleepChar;
+extern const char SettingFastChar;
+extern const char SettingMediumChar;
+extern const char SettingSlowChar;
+extern const char SettingRightChar;
+extern const char SettingLeftChar;
+extern const char SettingAutoChar;
+extern const char SettingTempCChar;
+extern const char SettingTempFChar;
+#endif /* STRINGS_H_ */
--- a/workspace/ts100/src/Analog.c
+++ b/workspace/ts100/src/Analog.c
@@ -14,6 +14,7 @@ uint16_t readDCVoltage(uint16_t divFactor) {
 	uint16_t reading = 0;
 	for (u8 i = 0; i < 10; i++) {
 		reading += ADC_GetConversionValue(ADC2);
+		delayMs(5);
 	}
 	reading /= divFactor; //take the average and convert to X10 voltage
 	return reading; //return the read voltage
@@ -23,7 +24,7 @@ uint16_t readDCVoltage(uint16_t divFactor) {
 //This allows us to read it in X10 mode
 //Returns temperature in C X10 mode
 int16_t readTipTemp() {
-	static uint32_t rollingAverage[16];
+	static uint32_t rollingAverage[8];
 	static uint8_t rIndex = 0;

 	/*The head has a thermocouple inline with the heater
@@ -54,13 +55,10 @@ int16_t readTipTemp() {
 	ad_sum = ad_sum - max - min; //remove the two outliers
 	avg_data = ad_sum / 8; //take the average
 	rollingAverage[rIndex] = avg_data;
-	rIndex = (rIndex + 1) % 16;
+	rIndex = (rIndex + 1) % 8;
 	return (rollingAverage[0] + rollingAverage[1] + rollingAverage[2]
 			+ rollingAverage[3] + rollingAverage[4] + rollingAverage[5]
-			+ rollingAverage[6] + rollingAverage[7] + rollingAverage[8]
-			+ rollingAverage[9] + rollingAverage[10] + rollingAverage[11]
-			+ rollingAverage[12] + rollingAverage[13] + rollingAverage[14]
-			+ rollingAverage[15]) / 16; //get the average
+			+ rollingAverage[6] + rollingAverage[7]) / 8;

 }

--- a/workspace/ts100/src/Bios.c
+++ b/workspace/ts100/src/Bios.c
@@ -5,7 +5,6 @@
 #include "Bios.h"
 #include "I2C.h"

-
 #define ADC1_DR_Address    ((u32)0x4001244C)
 volatile uint32_t gHeat_cnt = 0;

@@ -56,7 +55,7 @@ void GPIO_Config(void) {
 	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE); // GPIOB & AFIO

 	GPIO_PinRemapConfig(GPIO_Remap_SWJ_NoJTRST, ENABLE);
-	GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
+	GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);//disables jtag and maps pins for SWD

 	//------ PA7 TMP36 Analog input ----------------------------------------//
 	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
@@ -64,7 +63,7 @@ void GPIO_Config(void) {
 	GPIO_Init(GPIOA, &GPIO_InitStructure);

 	//------ OLED_RST_PIN(PB9) ---------------------------------------------//
-	GPIO_InitStructure.GPIO_Pin = OLED_RST_PIN;
+	GPIO_InitStructure.GPIO_Pin = OLED_RST_PIN|GPIO_Pin_12;
 	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
 	GPIO_Init(GPIOA, &GPIO_InitStructure);
@@ -92,10 +91,16 @@ void GPIO_Config(void) {
 	GPIO_Init(GPIOA, &GPIO_InitStructure);

 	//--------INT 1 == PB5 -------------------------------------------------//
-	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
-	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;//pullup just in case something resets the accel
+	GPIO_InitStructure.GPIO_Pin = INT1_PIN;
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; //pullup just in case something resets the accel
 	GPIO_Init(GPIOB, &GPIO_InitStructure);

+	//--------INT 2 == PB3 -------------------------------------------------//
+	GPIO_InitStructure.GPIO_Pin = INT2_PIN;
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; //pullup just in case something resets the accel
+	GPIO_Init(GPIOB, &GPIO_InitStructure);
+
+	GPIO_ResetBits(GPIOA, GPIO_Pin_12);//Write PA12 low so USB does not enumerate
 }
 /*
 * Init the ADC's
@@ -150,7 +155,7 @@ void Adc_Init(void) {
 	ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 1,
 	ADC_SampleTime_239Cycles5); //28 or 55
 	ADC_RegularChannelConfig(ADC2, ADC_Channel_9, 1,
-	ADC_SampleTime_55Cycles5); //28 or 55
+	ADC_SampleTime_239Cycles5); //28 or 55

 	/* Enable ADC1 DMA */
 	ADC_DMACmd(ADC1, ENABLE);
@@ -211,7 +216,8 @@ void Init_EXTI(void) {
 	GPIO_PinSource5);     //PB5 == accelerometer

 	/* Configure EXTI5/6/9 line */
-	EXTI_InitStructure.EXTI_Line = EXTI_Line5 | EXTI_Line6 | EXTI_Line9;
+	EXTI_InitStructure.EXTI_Line = EXTI_Line5 | EXTI_Line6 | EXTI_Line9
+			| EXTI_Line3;
 	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
 	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling; //trigger on up and down
 	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
@@ -224,6 +230,13 @@ void Init_EXTI(void) {
 	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
 	NVIC_Init(&NVIC_InitStructure);

+	/* Enable and set EXTI9_5 Interrupt to the lowest priority */
+	NVIC_InitStructure.NVIC_IRQChannel = EXTI3_IRQn;
+	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x0F;
+	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x0F;
+	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
+	NVIC_Init(&NVIC_InitStructure);
+
 }
 //Start the system watchdog with a timeout specified
 //Note you cannot turn this off once you turn it on
@@ -250,7 +263,7 @@ void Clear_Watchdog(void) {

 //TIM3_ISR handles the tick of the timer 3 IRQ
 void TIM3_ISR(void) {
-	volatile static u8 heat_flag = 0;
+	static volatile u8 heat_flag = 0;
 	//heat flag == used to make the pin toggle
 	//As the output is passed through a cap, the iron is on whilever we provide a square wave drive output

--- a/workspace/ts100/src/I2C.c
+++ b/workspace/ts100/src/I2C.c
@@ -4,6 +4,19 @@
 */
 #include "I2C.h"

+/* I2C STOP mask */
+#define CR1_STOP_Set            ((uint16_t)0x0200)
+#define CR1_STOP_Reset          ((uint16_t)0xFDFF)
+
+/* I2C ACK mask */
+#define CR1_ACK_Set             ((uint16_t)0x0400)
+#define CR1_ACK_Reset           ((uint16_t)0xFBFF)
+
+/* I2C POS mask */
+#define CR1_POS_Set             ((uint16_t)0x0800)
+#define CR1_POS_Reset           ((uint16_t)0xF7FF)
+
+#define NULL ((void *)0)
 /*
 * Configure the I2C port hardware
 */
@@ -60,89 +73,222 @@ void I2C_PageWrite(u8* buf, u8 nbyte, u8 deviceaddr) {
 	}

 }
+//Based on code from http://iamjustinwang.blogspot.com.au/2016/03/stm32f103-i2c-master-driver.html
+int I2C_Master_Read(uint8_t deviceAddr, uint8_t readAddr, uint8_t* pBuffer,
+		uint16_t numByteToRead) {

-/*
- * Read Page of data using I2C1 peripheral
- */
+	__IO uint32_t temp = 0;
+	volatile int I2C_TimeOut = temp;

-void I2C_PageRead(u8* buf, u8 nbyte, u8 deviceaddr, u8 readaddr) {
-	I2C_GenerateSTART(I2C1, ENABLE);
-	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_SB) == RESET)
-		;
-	I2C_Send7bitAddress(I2C1, deviceaddr << 1, I2C_Direction_Transmitter);
-	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_ADDR) == RESET)
-		;
-	I2C_GetFlagStatus(I2C1, I2C_FLAG_MSL);
-	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_TXE) == RESET)
-		;
-	// Send an 8bit byte address
-	I2C_SendData(I2C1, readaddr);
+	// /* While the bus is busy * /
+	I2C_TimeOut = 1000;
 	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY)) {
-	}
-	I2C_AcknowledgeConfig(I2C1, DISABLE);
-	I2C_NACKPositionConfig(I2C1, I2C_NACKPosition_Current);
-	I2C_GenerateSTART(I2C1, ENABLE);
-	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) {
-	}
-	I2C_Send7bitAddress(I2C1, deviceaddr << 1, I2C_Direction_Receiver);
-	while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_ADDR)) {
-	}
-	if (nbyte == 1) {
-		// Clear Ack bit
-		I2C_AcknowledgeConfig(I2C1, DISABLE);
-		// EV6_1 -- must be atomic -- Clear ADDR, generate STOP
-		__disable_irq();
-		(void) I2C1->SR2;
-		I2C_GenerateSTOP(I2C1, ENABLE);
-		__enable_irq();
-		// Receive data   EV7
-		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_RXNE)) {
-		}
-		*buf++ = I2C_ReceiveData(I2C1);
-	} else if (nbyte == 2) {
-		// Set POS flag
-		I2C_NACKPositionConfig(I2C1, I2C_NACKPosition_Next);
-		// EV6_1 -- must be atomic and in this order
-		__disable_irq();
-		(void) I2C1->SR2;                           // Clear ADDR flag
-		I2C_AcknowledgeConfig(I2C1, DISABLE);       // Clear Ack bit
-		__enable_irq();
-		// EV7_3  -- Wait for BTF, program stop, read data twice
-		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
-		}
-		__disable_irq();
-		I2C_GenerateSTOP(I2C1, ENABLE);
-		*buf++ = I2C1->DR;
-		__enable_irq();
-		*buf++ = I2C1->DR;
-	} else {
-		(void) I2C1->SR2;                           // Clear ADDR flag
-		while (nbyte-- != 3) {
-			// EV7 -- cannot guarantee 1 transfer completion time, wait for BTF
-			//        instead of RXNE
-			while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
-			}
-			*buf++ = I2C_ReceiveData(I2C1);
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
 		}
+	}

-		while (!I2C_GetFlagStatus(I2C1, I2C_FLAG_BTF)) {
+	// * Send START condition * /
+	I2C_GenerateSTART(I2C1, ENABLE);
+
+	// / * Test on EV5 and clear it * /
+	I2C_TimeOut = 1000;
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) {
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
 		}
-		// EV7_2 -- Figure 1 has an error, doesn't read N-2 !
-		I2C_AcknowledgeConfig(I2C1, DISABLE);           // clear ack bit
+	}
+
+	// / * Send  address for write  * /
+	I2C_Send7bitAddress(I2C1, deviceAddr, I2C_Direction_Transmitter);
+
+	// / * Test on EV6 and clear it * /
+	I2C_TimeOut = 1000;
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)) {
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
+		}
+	}
+
+	// / * Send the internal address to read from: Only one byte address  * /
+	I2C_SendData(I2C1, readAddr);
+
+	/// * Test on EV8 and clear it * /
+	I2C_TimeOut = 1000;
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)) {
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
+		}
+	}
+
+	/// * Send STRAT condition a second time * /
+	I2C_GenerateSTART(I2C1, ENABLE);
+
+	/// * Test on EV5 and clear it * /
+	I2C_TimeOut = 1000;
+	while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) {
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
+		}
+	}
+
+	// * Send  address for read * /
+	I2C_Send7bitAddress(I2C1, deviceAddr, I2C_Direction_Receiver);
+
+	if (numByteToRead == 1) {
+		/* Wait until ADDR is set */
+		I2C_TimeOut = 1000;
+		while ((I2C1->SR1 & 0x0002) != 0x0002) {
+			if (I2C_TimeOut-- <= 0) {
+				return 1;
+			}
+		}
+		/* Clear ACK bit */
+		I2C1->CR1 &= CR1_ACK_Reset;
+		/* Disable all active IRQs around ADDR clearing and STOP programming because the EV6_3
+		 software sequence must complete before the current byte end of transfer */
 		__disable_irq();
-		*buf++ = I2C_ReceiveData(I2C1);             // receive byte N-2
-		I2C_GenerateSTOP(I2C1, ENABLE);                  // program stop
+		/* Clear ADDR flag */
+		temp = I2C1->SR2;
+		/* Program the STOP */
+		I2C_GenerateSTOP(I2C1, ENABLE);
+		/* Re-enable IRQs */
 		__enable_irq();
-		*buf++ = I2C_ReceiveData(I2C1);             // receive byte N-1
-		// wait for byte N
-		while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_RECEIVED)) {
+		/* Wait until a data is received in DR register (RXNE = 1) EV7 */
+		I2C_TimeOut = 1000;
+		while ((I2C1->SR1 & 0x00040) != 0x000040) {
+			if (I2C_TimeOut-- <= 0) {
+				return 1;
+			}
 		}
-		*buf++ = I2C_ReceiveData(I2C1);
-		nbyte = 0;
+		/* Read the data */
+		*pBuffer = I2C1->DR;
+
+	} else if (numByteToRead == 2) {
+
+		/* Set POS bit */
+		I2C1->CR1 |= CR1_POS_Set;
+		/* Wait until ADDR is set: EV6 */
+		I2C_TimeOut = 1000;
+		while ((I2C1->SR1 & 0x0002) != 0x0002) {
+			if (I2C_TimeOut-- <= 0) {
+				return 1;
+			}
+		}
+		/* EV6_1: The acknowledge disable should be done just after EV6,
+		 that is after ADDR is cleared, so disable all active IRQs around ADDR clearing and
+		 ACK clearing */
+		__disable_irq();
+		/* Clear ADDR by reading SR2 register  */
+		temp = I2C1->SR2;
+		/* Clear ACK */
+		I2C1->CR1 &= CR1_ACK_Reset;
+		/*Re-enable IRQs */
+		__enable_irq();
+		/* Wait until BTF is set */
+		I2C_TimeOut = 1000;
+		while ((I2C1->SR1 & 0x00004) != 0x000004) {
+			if (I2C_TimeOut-- <= 0) {
+				return 1;
+			}
+		}
+		/* Disable IRQs around STOP programming and data reading */
+		__disable_irq();
+		/* Program the STOP */
+		I2C_GenerateSTOP(I2C1, ENABLE);
+		/* Read first data */
+		*pBuffer = I2C1->DR;
+		/* Re-enable IRQs */
+		__enable_irq();
+		/**/
+		pBuffer++;
+		/* Read second data */
+		*pBuffer = I2C1->DR;
+		/* Clear POS bit */
+		I2C1->CR1 &= CR1_POS_Reset;
 	}
-	// Wait for stop
-	while (I2C_GetFlagStatus(I2C1, I2C_FLAG_STOPF)) {
+
+	else { //numByteToRead > 2
+		   // * Test on EV6 and clear it * /
+		I2C_TimeOut = 1000;
+		while (!I2C_CheckEvent(I2C1,
+		I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED)) {
+			if (I2C_TimeOut-- <= 0) {
+				return 1;
+			}
+		}
+		// * While there is data to be read * /
+		while (numByteToRead) {
+			/* Receive bytes from first byte until byte N-3 */
+			if (numByteToRead != 3) {
+				/* Poll on BTF to receive data because in polling mode we can not guarantee the
+				 EV7 software sequence is managed before the current byte transfer completes */
+				I2C_TimeOut = 1000;
+				while ((I2C1->SR1 & 0x00004) != 0x000004) {
+					if (I2C_TimeOut-- <= 0) {
+						return 1;
+					}
+				}
+				/* Read data */
+				*pBuffer = I2C1->DR;
+				pBuffer++;
+				/* Decrement the read bytes counter */
+				numByteToRead--;
+			}
+
+			/* it remains to read three data: data N-2, data N-1, Data N */
+			if (numByteToRead == 3) {
+				/* Wait until BTF is set: Data N-2 in DR and data N -1 in shift register */
+				I2C_TimeOut = 1000;
+				while ((I2C1->SR1 & 0x00004) != 0x000004) {
+					if (I2C_TimeOut-- <= 0) {
+						return 1;
+					}
+				}
+				/* Clear ACK */
+				I2C1->CR1 &= CR1_ACK_Reset;
+
+				/* Disable IRQs around data reading and STOP programming */
+				__disable_irq();
+				/* Read Data N-2 */
+				*pBuffer = I2C1->DR;
+				/* Increment */
+				pBuffer++;
+				/* Program the STOP */
+				I2C1->CR1 |= CR1_STOP_Set;
+				/* Read DataN-1 */
+				*pBuffer = I2C1->DR;
+				/* Re-enable IRQs */
+				__enable_irq();
+				/* Increment */
+				pBuffer++;
+				/* Wait until RXNE is set (DR contains the last data) */
+				I2C_TimeOut = 1000;
+				while ((I2C1->SR1 & 0x00040) != 0x000040) {
+					if (I2C_TimeOut-- <= 0) {
+						return 1;
+					}
+				}
+				/* Read DataN */
+				*pBuffer = I2C1->DR;
+				/* Reset the number of bytes to be read by master */
+				numByteToRead = 0;
+			}
+		}
 	}
-	return;
+
+	/* Make sure that the STOP bit is cleared by Hardware before CR1 write access */
+	I2C_TimeOut = 1000;
+	while ((I2C1->CR1 & 0x200) == 0x200) {
+		if (I2C_TimeOut-- <= 0) {
+			return 1;
+		}
+	}
+
+	// * Enable Acknowledgment to be ready for another reception * /
+	I2C_AcknowledgeConfig(I2C1, ENABLE);
+
+	return 0;
+
 }

--- a/workspace/ts100/src/Interrupt.c
+++ b/workspace/ts100/src/Interrupt.c
@@ -3,10 +3,13 @@
 #include "I2C.h"

 volatile uint32_t system_Ticks;
-volatile uint32_t lastKeyPress; //millis() at the last button event
-volatile uint8_t keyState; //tracks the button status
+volatile uint32_t BkeyChange; //millis() at the last button event
+volatile uint32_t AkeyChange;
 volatile uint8_t rawKeys;
+volatile uint8_t LongKeys;
 volatile uint32_t lastMovement; //millis() at last movement event
+volatile uint8_t RotationChangedFlag;
+volatile uint8_t InterruptMask;

 //Delay in milliseconds using systemTick
 void delayMs(uint32_t ticks) {
@@ -14,6 +17,104 @@ void delayMs(uint32_t ticks) {
 	while (millis() < endtime)
 		;
 }
+uint32_t getLastButtonPress() {
+	if (BkeyChange > AkeyChange)
+		return BkeyChange;
+	return AkeyChange;
+}
+uint8_t getButtons() {
+	//We want to check the times for the lat buttons & also the rawKeys state
+	//If a key has just gone down, rawKeys & KEY ==1
+	//This is effectively just a big switch statement to handle a small delay on triggering to stop bounce, and also handle key repeat
+	uint8_t out = 0;
+	//Special handling case for two keys down at once
+	//This is here to allow for people who do not manage to get both keys down within 50ms of each other.
+	if ((rawKeys & (BUT_A | BUT_B)) == (BUT_A | BUT_B)) {
+		//both keys are probably down
+		if (millis() - AkeyChange > 50)
+			if (millis() - BkeyChange > 50) {
+				out = (BUT_A | BUT_B);
+				AkeyChange = millis();
+				BkeyChange = millis();
+				rawKeys = 0;
+			}
+		LongKeys = 0;
+	} else {
+		if (millis() - AkeyChange > 80) {
+			if (LongKeys & BUT_A) {
+				if (rawKeys & BUT_A) {
+					if (millis() - AkeyChange > 800) {
+						out |= BUT_A;
+						AkeyChange = millis();
+						LongKeys &= ~BUT_A;
+
+						LongKeys |= (BUT_A << 2);
+					}
+				} else {
+					LongKeys &= ~BUT_A;
+					LongKeys &= ~(BUT_A << 2);
+				}
+
+			} else if (LongKeys & (BUT_A << 2)) {
+				if (rawKeys & BUT_A) {
+					if (millis() - AkeyChange > 100) {
+						out |= BUT_A;
+						AkeyChange = millis();
+					}
+				} else {
+					LongKeys &= ~BUT_A;
+					LongKeys &= ~(BUT_A << 2);
+				}
+			} else {
+				if (rawKeys & BUT_A) {
+					//The key is down
+					out |= BUT_A;
+					LongKeys |= BUT_A;
+				} else {
+					//The key has been lifted
+					LongKeys &= ~BUT_A;
+					LongKeys &= ~(BUT_A << 2);
+				}
+			}
+		}
+		if (millis() - BkeyChange > 80) {
+			if (LongKeys & BUT_B) {
+				if (rawKeys & BUT_B) {
+					if (millis() - BkeyChange > 800) {
+						out |= BUT_B;
+						BkeyChange = millis();
+						LongKeys |= (BUT_B << 2);
+						LongKeys &= ~BUT_B;
+					}
+				} else {
+					LongKeys &= ~BUT_B;
+					LongKeys &= ~(BUT_B << 2);
+				}
+			} else if (LongKeys & (BUT_B << 2)) {
+				if (rawKeys & BUT_B) {
+					if (millis() - BkeyChange > 100) {
+						out |= BUT_B;
+						BkeyChange = millis();
+					}
+				} else {
+					LongKeys &= ~BUT_B;
+					LongKeys &= ~(BUT_B << 2);
+				}
+			} else {
+				if (rawKeys & BUT_B) {
+					//The key is down
+					out |= BUT_B;
+					LongKeys |= BUT_B;
+				} else {
+					//The key has been lifted
+					LongKeys &= ~BUT_B;
+					LongKeys &= ~(BUT_B << 2);
+				}
+			}
+		}
+	}
+	return out;
+}

 void NMI_Handler(void) {
 	;
@@ -57,30 +158,33 @@ void EXTI9_5_IRQHandler(void) {
 	//Line 5 == movement
 	if (EXTI_GetITStatus(EXTI_Line9) != RESET) {
 		if (GPIO_ReadInputDataBit(GPIOA, KEY_A) == SET) {
-			keyState &= ~(BUT_A);
 			rawKeys &= ~BUT_A;
 		} else {
-			keyState |= BUT_A;
 			rawKeys |= BUT_A;
-			lastKeyPress = millis();
 		}
+		AkeyChange = millis();
 		EXTI_ClearITPendingBit(EXTI_Line9);
 	} else if (EXTI_GetITStatus(EXTI_Line6) != RESET) {
 		if (GPIO_ReadInputDataBit(GPIOA, KEY_B) == SET) {
-			keyState &= ~(BUT_B);
 			rawKeys &= ~BUT_B;
 		} else {
-			keyState |= BUT_B;
 			rawKeys |= BUT_B;
-			lastKeyPress = millis();
 		}
+		BkeyChange = millis();
 		EXTI_ClearITPendingBit(EXTI_Line6);
 	} else if (EXTI_GetITStatus(EXTI_Line5) != RESET) {	//Movement Event
-		lastMovement = millis();
+		if (!InterruptMask)
+			lastMovement = millis();
 		EXTI_ClearITPendingBit(EXTI_Line5);
 	}

 }
+void EXTI3_IRQHandler(void) {
+	if (EXTI_GetITStatus(EXTI_Line3) != RESET) {	//Orientation Change
+		RotationChangedFlag = 1;
+		EXTI_ClearITPendingBit(EXTI_Line3);
+	}
+}

 /*********************** UNUSED IRQ *****************************************/
 void WWDG_IRQHandler(void) {
@@ -101,8 +205,7 @@ void EXTI1_IRQHandler(void) {
 }
 void EXTI2_IRQHandler(void) {
 }
-void EXTI3_IRQHandler(void) {
-}
+
 void EXTI4_IRQHandler(void) {
 }
 void DMA1_Channel1_IRQHandler(void) {
--- a/workspace/ts100/src/MMA8652FC.c
+++ b/workspace/ts100/src/MMA8652FC.c
@@ -23,24 +23,38 @@ void I2C_RegisterWrite(uint8_t reg, uint8_t data) {
 }

 uint8_t I2C_RegisterRead(uint8_t reg) {
-	u8 tx_data[3];
-	tx_data[0] = reg;
-	I2C_PageRead(tx_data, 1, DEVICE_ADDR, reg);
+	u8 tx_data[1];
+	I2C_Master_Read(DEVICE_ADDR << 1, reg, tx_data, 1);
 	return tx_data[0];
 }

+uint8_t getOrientation() {
+//First read the PL_STATUS register
+	uint8_t plStatus = I2C_RegisterRead(PL_STATUS_REG);
+	plStatus >>= 1; //We dont need the up/down bit
+	plStatus &= 0x03; //mask to the two lower bits
+	//0 == left handed
+	//1 == right handed
+
+	return plStatus;
+}
+
 void StartUp_Accelerometer(uint8_t sensitivity) {
 	I2C_RegisterWrite(CTRL_REG2, 0); //Normal mode
 	I2C_RegisterWrite( CTRL_REG2, 0x40);	// Reset all registers to POR values
 	delayMs(2);		// ~1ms delay
 	I2C_RegisterWrite(FF_MT_CFG_REG, 0x78);	// Enable motion detection for X and Y axis, latch enabled
-	uint8_t sens = 9 * 7 + 5;
-	sens -= 7 * sensitivity;
+	uint8_t sens = 9 * 6 + 5;
+	sens -= 6 * sensitivity;

 	I2C_RegisterWrite(FF_MT_THS_REG, 0x80 | sens);		// Set threshold
 	I2C_RegisterWrite(FF_MT_COUNT_REG, 0x02);	// Set debounce to 100ms
-
-	I2C_RegisterWrite( CTRL_REG4, 0x04);		// Enable motion interrupt
-	I2C_RegisterWrite( CTRL_REG5, 0x04);// Route motion interrupts to INT1 ->PB5 ->EXTI5
+	I2C_RegisterWrite(PL_CFG_REG, 0x40);	//Enable the orientation detection
+	I2C_RegisterWrite(PL_COUNT_REG, 200);	//200 count debounce
+	I2C_RegisterWrite(PL_BF_ZCOMP_REG, 0b01000111);	//Set the threshold to 42 degrees
+	I2C_RegisterWrite(P_L_THS_REG, 0b10011100);	//Up the trip angles
+	I2C_RegisterWrite( CTRL_REG4, 0x04 | (1<<4));	// Enable motion interrupt & orientation interrupt
+	I2C_RegisterWrite( CTRL_REG5, 0x04);// Route motion interrupts to INT1 ->PB5 ->EXTI5, leaving orientation routed to INT2
 	I2C_RegisterWrite( CTRL_REG1, 0x11);		// ODR=800 Hz, Active mode
+
 }
--- a/workspace/ts100/src/Main.c
+++ b/workspace/ts100/src/Main.c
@@ -14,15 +14,50 @@ void setup();

 int main(void) {
 	setup();/*Setup the system*/
+	for(uint8_t i=0;i<100;i++)
+		readIronTemp(0, 1, 0xFFFF);
+	if (systemSettings.autoStart == 1)
+		operatingMode = SOLDERING;
+	else if (systemSettings.autoStart == 2)
+		operatingMode = SLEEP;
+	if (systemSettings.autoStart) {
+		InterruptMask = 1; //set the mask
+		lastMovement = 0;
+	} else
+		InterruptMask = 0;
+	if (readIronTemp(0, 1, 0xFFFF) > 500)
+		operatingMode = COOLING;
+
 	while (1) {
 		Clear_Watchdog(); //reset the Watch dog timer
 		ProcessUI();
 		DrawUI();
-		delayMs(50); //Slow the system down a little bit
-		if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_5) == Bit_RESET) {
+		OLED_Sync(); //Write out the screen buffer
+		delayMs(15); //Slow the system down waiting for the iron.
+
+		if (systemSettings.OrientationMode == 2) {
+			//Automatic mode
+			if (RotationChangedFlag) {
+				OLED_SetOrientation(!getOrientation());
+				RotationChangedFlag = 0;
+			} else if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_3) == Bit_RESET) {
+				OLED_SetOrientation(!getOrientation());
+				RotationChangedFlag = 0;
+				//^ This is a workaround for the IRQ being set off before we have the handler setup and enabled.
+			}
+		}
+		if ((GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_5) == Bit_RESET)
+				&& (!InterruptMask)) {
 			lastMovement = millis();
 			//This is a workaround for the line staying low as the user is still moving. (ie sensitivity is too high for their amount of movement)
 		}
+		delayMs(15); //Slow the system down waiting for the iron.
+		if (systemSettings.autoStart && (millis() > 10000) && InterruptMask) {
+			//If the user has setup the device to auto enter a startup mode, we normally have the interrupts on motion masked for the inital 10 seconds to prevent waking up during initalization
+			//This allows us to re-enable these interrupts.
+			InterruptMask = 0;
+
+		}
 	}
 }
 void setup() {
@@ -38,10 +73,26 @@ void setup() {
 	StartUp_Accelerometer(systemSettings.sensitivity); //Start the accelerometer
 	setupPID(); 										//Init the PID values
 	readIronTemp(systemSettings.tempCalibration, 0, 0); //load the default calibration value
-	Init_Oled(systemSettings.flipDisplay); 				//Init the OLED display
+	if (systemSettings.OrientationMode == 2)
+		Init_Oled(0); //Init the OLED display in RH mode, since accel wont have started up yet
+	else
+		Init_Oled(systemSettings.OrientationMode); 		//Init the OLED display

-	OLED_DrawString("VER 1.15", 8); 					//Version Number
-	delayMs(300);								//Pause to show version number
+	OLED_DrawString("Ver 1.17", 8); 					//Version Number
+	OLED_Sync();
+	delayMs(400);						//Pause to show version number
 	showBootLogoIfavailable();
-	Start_Watchdog(1000); 		//start the system watch dog as 1 second timeout
+	//RESETs settings
+	if (GPIO_ReadInputDataBit(GPIOA, KEY_B) == Bit_RESET) {
+		OLED_DrawString("Reset  ?", 8);
+		delayMs(1000);
+		if (GPIO_ReadInputDataBit(GPIOA, KEY_B) == Bit_RESET) {
+			OLED_DrawString("   OK   ", 8);
+			delayMs(1000);
+			resetSettings();
+		}
+	}
+
+	Start_Watchdog(5000); //start the system watch dog as 5 second timeout
+
 }
--- a/workspace/ts100/src/Modes.c
+++ b/workspace/ts100/src/Modes.c
@@ -5,33 +5,21 @@
 *      Author: Ralim <ralim@ralimtek.com>
 */
 #include "Modes.h"
-const char *SettingsLongNames[] = {
-		"      Power source. Sets cutoff voltage. <DC 10V> <S 3.3V per cell>",
-		"      Sleep Temperature <C>", "      Sleep Timeout <Minutes>",
-		"      Shutdown Timeout <Minutes>",
-		"      Motion Sensitivity <0.Off 1.least sensitive 9.most sensitive>",
-		"      Temperature Unit", "      Temperature Rounding Amount",
-		"      Temperature Display Update Rate",
-		"      Flip Display for Left Hand",
-		"      Enable front key boost 450C mode when soldering",
-		"      Temperature when in boost mode" };
+
 uint8_t StatusFlags = 0;
 uint32_t temporaryTempStorage = 0;
+
+operatingModeEnum operatingMode;
+settingsPageEnum settingsPage;
+
 //This does the required processing and state changes
 void ProcessUI() {
 	uint8_t Buttons = getButtons(); //read the buttons status
 	static uint32_t lastModeChange = 0;
-	if (getRawButtons() && ((millis() - getLastButtonPress()) > 1000)) {
-		lastKeyPress = millis() - 600;
-		Buttons = getRawButtons();
-	} else if (millis() - getLastButtonPress() < 80) {
-		Buttons = 0;
-	} else if (Buttons != 0) {
-		resetButtons();
-	}

 	switch (operatingMode) {
 	case STARTUP:
+
 		if (Buttons == (BUT_A | BUT_B)) {
 			operatingMode = THERMOMETER;
 		} else if (Buttons == BUT_A) {
@@ -45,6 +33,8 @@ void ProcessUI() {
 		}
 		break;
 	case SOLDERING:
+
+		//^ This is to make the button more delayed in timing for people to find A+B easier
 		//We need to check the buttons if we need to jump out
 		if ((Buttons == BUT_A && !systemSettings.boostModeEnabled)
 				|| Buttons == BUT_B) {
@@ -84,15 +74,20 @@ void ProcessUI() {
 				StatusFlags = 0;
 			}
 			//We need to check the timer for movement in case we need to goto idle
-			if (systemSettings.sensitivity)
-				if (millis() - getLastMovement()
-						> (systemSettings.SleepTime * 60000)) {
-					if (millis() - getLastButtonPress()
-							> (systemSettings.SleepTime * 60000)) {
+			if (systemSettings.sensitivity) {
+				uint32_t timeout = 0;
+				if (systemSettings.SleepTime < 6)
+					timeout = 1000 * 10 * systemSettings.SleepTime;
+				else
+					timeout = 60 * 1000 * (systemSettings.SleepTime - 5);
+
+				if (millis() - getLastMovement() > (timeout)) {
+					if (millis() - getLastButtonPress() > (timeout)) {
 						operatingMode = SLEEP;
 						return;
 					}
 				}
+			}
 			uint16_t voltage = readDCVoltage(systemSettings.voltageDiv); //get X10 voltage
 			if ((voltage) < lookupVoltageLevel(systemSettings.cutoutSetting)) {
 				operatingMode = UVLOWARN;
@@ -104,23 +99,47 @@ void ProcessUI() {
 		}
 		break;
 	case TEMP_ADJ:
-		if (Buttons == BUT_A) {
-			//A key pressed so we are moving down in temp
+		if (OLED_GetOrientation() == 1) {
+			if (Buttons == BUT_B) {
+				//A key pressed so we are moving down in temp

-			if (systemSettings.SolderingTemp > 1000)
-				systemSettings.SolderingTemp -= 100;
-		} else if (Buttons == BUT_B) {
-			//B key pressed so we are moving up in temp
-			if (systemSettings.SolderingTemp < 4500)
-				systemSettings.SolderingTemp += 100;
+				if (systemSettings.SolderingTemp > 1000)
+					systemSettings.SolderingTemp -= 100;
+			} else if (Buttons == BUT_A) {
+				//B key pressed so we are moving up in temp
+				if (systemSettings.SolderingTemp < 4500)
+					systemSettings.SolderingTemp += 100;
+			} else {
+				//we check the timeout for how long the buttons have not been pushed
+				//if idle for > 3 seconds then we return to soldering
+				//Or if both buttons pressed
+				if (Buttons == (BUT_A | BUT_B)) {
+					operatingMode = STARTUP;
+					saveSettings();
+				} else if ((millis() - getLastButtonPress() > 2000)) {
+					operatingMode = SOLDERING;
+				}
+
+			}
 		} else {
-			//we check the timeout for how long the buttons have not been pushed
-			//if idle for > 3 seconds then we return to soldering
-			//Or if both buttons pressed
-			if ((millis() - getLastButtonPress() > 2000)
-					|| Buttons == (BUT_A | BUT_B)) {
-				operatingMode = SOLDERING;
-				saveSettings();
+			if (Buttons == BUT_A) {
+				//A key pressed so we are moving down in temp
+
+				if (systemSettings.SolderingTemp > 1000)
+					systemSettings.SolderingTemp -= 100;
+			} else if (Buttons == BUT_B) {
+				//B key pressed so we are moving up in temp
+				if (systemSettings.SolderingTemp < 4500)
+					systemSettings.SolderingTemp += 100;
+			} else {
+				//we check the timeout for how long the buttons have not been pushed
+				//if idle for > 3 seconds then we return to soldering
+				//Or if both buttons pressed
+				if ((millis() - getLastButtonPress() > 2000)
+						|| Buttons == (BUT_A | BUT_B)) {
+					operatingMode = SOLDERING;
+					saveSettings();
+				}
 			}
 		}
 		break;
@@ -131,46 +150,59 @@ void ProcessUI() {
 			//The user pressed the button to breakout of the settings help prompt
 			StatusFlags = 0;
 		} else {
-			if (Buttons & BUT_B) {
+			if (Buttons == (BUT_A | BUT_B)) {
+
+				//Both buttons were pressed, exit back to the startup screen
+				settingsPage = 0;				//reset
+				operatingMode = STARTUP;	//reset back to the startup
+				saveSettings();					//Save the settings
+				StartUp_Accelerometer(systemSettings.sensitivity); //Start the accelerometer
+
+			} else if (Buttons & BUT_B) {
 				//A key iterates through the menu
 				if (settingsPage == SETTINGSOPTIONSCOUNT) {
 					//Roll off the end
 					settingsPage = 0;				//reset
-					operatingMode = STARTUP;		//reset back to the startup
+					operatingMode = STARTUP;	//reset back to the startup
 					saveSettings();					//Save the settings
+					StartUp_Accelerometer(systemSettings.sensitivity); //Start the accelerometer
+
 				} else {
-					++settingsPage;					//move to the next option
+					++settingsPage;			//move to the next option
 				}
 			} else if (Buttons & BUT_A) {
 				//B changes the value selected
 				switch (settingsPage) {
 				case UVCO:
 					//we are incrementing the cutout voltage
-					systemSettings.cutoutSetting += 1;		//Go up 1V at a jump
+					systemSettings.cutoutSetting += 1;	//Go up 1V at a jump
 					systemSettings.cutoutSetting %= 5;		//wrap 0->4
 					break;
 				case SLEEP_TEMP:
 					systemSettings.SleepTemp += 100;	//Go up 10C at a time
 					if (systemSettings.SleepTemp > 3000)
-						systemSettings.SleepTemp = 1000;//cant sleep higher than 300
+						systemSettings.SleepTemp = 500;	//cant sleep higher than 300 or less than 50
 					break;
 				case SLEEP_TIME:
-					++systemSettings.SleepTime;		//Go up 1 minute at a time
-					if (systemSettings.SleepTime > 30)
+					++systemSettings.SleepTime;	//Go up 1 minute at a time
+					if (systemSettings.SleepTime > 16)
 						systemSettings.SleepTime = 1;//can't set time over 30 mins
 					//Remember that ^ is the time of no movement
 					break;
 				case SHUTDOWN_TIME:
 					++systemSettings.ShutdownTime;
 					if (systemSettings.ShutdownTime > 60)
-						systemSettings.ShutdownTime = 0;		//wrap to off
+						systemSettings.ShutdownTime = 0;	//wrap to off
 					break;
 				case TEMPDISPLAY:
 					systemSettings.displayTempInF =
 							!systemSettings.displayTempInF;
 					break;
-				case LEFTY:
-					systemSettings.flipDisplay = !systemSettings.flipDisplay;
+				case SCREENROTATION:
+					systemSettings.OrientationMode++;
+					systemSettings.OrientationMode =
+							systemSettings.OrientationMode % 3;
+
 					break;
 				case MOTIONSENSITIVITY:
 					systemSettings.sensitivity++;
@@ -197,6 +229,31 @@ void ProcessUI() {
 					if (systemSettings.BoostTemp > 4500)
 						systemSettings.BoostTemp = 2500;	//loop back at 250
 					break;
+				case POWERDISPLAY:
+					systemSettings.powerDisplay = !systemSettings.powerDisplay;
+					break;
+				case AUTOSTART:
+					systemSettings.autoStart++;
+					systemSettings.autoStart %= 3;
+					break;
+				case COOLINGBLINK:
+					systemSettings.coolingTempBlink =
+							!systemSettings.coolingTempBlink;
+					break;
+#ifdef PIDTUNING
+					case PIDP:
+					pidSettings.kp++;
+					pidSettings.kp %= 20;
+					break;
+					case PIDI:
+					pidSettings.ki++;
+					pidSettings.ki %= 10;
+					break;
+					case PIDD:
+					pidSettings.kd++;
+					pidSettings.kd %= 30;
+					break;
+#endif
 				default:
 					break;
 				}
@@ -215,7 +272,7 @@ void ProcessUI() {
 			operatingMode = SOLDERING;
 			Oled_DisplayOn();
 			return;
-		} else if (systemSettings.sensitivity) {
+		} else if (systemSettings.sensitivity && !InterruptMask) {
 			if (millis() - getLastMovement() < 1000) {//moved in the last second
 				operatingMode = SOLDERING; //Goto active mode again
 				Oled_DisplayOn();
@@ -243,18 +300,7 @@ void ProcessUI() {
 			//Either button was pushed
 			operatingMode = STARTUP;
 		}
-		if (systemSettings.sensitivity) {
-			if (millis() - getLastMovement()
-					> (systemSettings.ShutdownTime * 60000)) {
-				if ((millis() - getLastButtonPress()
-						> systemSettings.ShutdownTime * 60000)) {
-					Oled_DisplayOff();
-				}
-			} else {
-				Oled_DisplayOn();
-			}
-		} else
-			Oled_DisplayOn();
+
 	}
 		break;
 	case UVLOWARN:
@@ -297,12 +343,12 @@ void ProcessUI() {
 		} else {
 			//User is calibrating the dc input
 			if (Buttons == BUT_A) {
-				if (!systemSettings.flipDisplay)
+				if (!systemSettings.OrientationMode)
 					systemSettings.voltageDiv++;
 				else
 					systemSettings.voltageDiv--;
 			} else if (Buttons == BUT_B) {
-				if (!systemSettings.flipDisplay)
+				if (!systemSettings.OrientationMode)
 					systemSettings.voltageDiv--;
 				else
 					systemSettings.voltageDiv++;
@@ -371,23 +417,29 @@ void drawTemp(uint16_t temp, uint8_t x, uint8_t roundingMode) {
 */
 void DrawUI() {
 	static uint32_t lastOLEDDrawTime = 0;
+
 	static uint16_t lastSolderingDrawnTemp1 = 0;
 	static uint16_t lastSolderingDrawnTemp2 = 0;
-
 	static uint8_t settingsLongTestScrollPos = 0;
 	uint16_t temp = readIronTemp(0, 0, 0xFFFF);
-	switch (operatingMode) {
-	case STARTUP:
-		//We are chilling in the idle mode
-		//Check if movement in the last 5 minutes , if not sleep OLED
+	if (systemSettings.sensitivity) {
 		if (millis() - getLastMovement() > (5 * 60 * 1000)
-				&& (millis() - getLastButtonPress() > (5 * 60 * 1000))) {
+				&& (millis() - getLastButtonPress() > (5 * 60 * 1000))
+				&& (temp < 400)) {
 			//OLED off
 			Oled_DisplayOff();
 		} else {
 			Oled_DisplayOn();
-			OLED_DrawIDLELogo();		//Draw the icons for prompting the user
 		}
+	}
+	switch (operatingMode) {
+	case STARTUP:
+		//We are chilling in the idle mode
+		//Check if movement in the last 5 minutes , if not sleep OLED
+
+		OLED_DrawIDLELogo();	//Draw the icons for prompting the user
+		temp = readIronTemp(0, 1, 0xFFFF);//to update the internal filter buffer
+
 		break;
 	case SOLDERING:
 		//The user is soldering
@@ -398,22 +450,23 @@ void DrawUI() {
 		else if (systemSettings.displayUpdateSpeed == DISPLAYMODE_MEDIUM
 				&& (millis() - lastOLEDDrawTime < 100))
 			return;
-		else if (systemSettings.displayUpdateSpeed == DISPLAYMODE_FAST
-				&& (millis() - lastOLEDDrawTime < 50))
-			return;

+		Clear_Screen();
+		Oled_DisplayOn();
 		uint32_t tempavg = (temp + lastSolderingDrawnTemp1
 				+ lastSolderingDrawnTemp2);
 		tempavg /= 3;
+
 		drawTemp(tempavg, 0, systemSettings.temperatureRounding);
 		lastSolderingDrawnTemp1 = temp;
 		lastSolderingDrawnTemp2 = lastSolderingDrawnTemp1;
 		lastOLEDDrawTime = millis();
+
 		//Now draw symbols
 		if (StatusFlags == 8)
-			OLED_DrawChar('B', 4);
+			OLED_DrawExtraFontChars(2, 4);
 		else {
-			OLED_DrawChar(' ', 4);
+			OLED_DrawChar(' ', 4, 0);
 		}
 		//Draw in battery symbol if desired
 		if (systemSettings.cutoutSetting) {
@@ -427,27 +480,40 @@ void DrawUI() {
 			if (cellV < 33)
 				cellV = 33;
 			cellV -= 33;			//Should leave us a number of 0-9
-			OLED_DrawExtendedChar(cellV + 1, 5);
-		} else {
-			OLED_DrawChar(' ', 5);
-		}
-		OLED_BlankSlot(6 * 12 + 16, 24 - 16);//blank out the tail after the arrows
-		if (getIronTimer() == 0
-				&& (temp / 10) > (systemSettings.SolderingTemp / 10)) {
-			//Cooling
-			OLED_DrawSymbol(6, 5);
-		} else {
-			if (getIronTimer() < 1500) {
-				//Maintaining
-				OLED_DrawSymbol(6, 7);
-			} else {		//we are heating
-				OLED_DrawSymbol(6, 6);
-			}
+			if (cellV > 9)
+				cellV = 9;
+			OLED_DrawSymbolChar(cellV + 1, 5);
 		}
+
 		if (systemSettings.displayTempInF) {
-			OLED_DrawChar('F', 3);
+			//OLED_DrawChar(SettingTempFChar, 3);
+			OLED_DrawExtraFontChars(0, 3);
 		} else {
-			OLED_DrawChar('C', 3);
+			//OLED_DrawChar(SettingTempCChar, 3);
+			OLED_DrawExtraFontChars(1, 3);
+		}
+		//Optionally draw the arrows, or draw the power instead
+		if (systemSettings.powerDisplay) {
+			//We want to draw in a neat little bar graph of power being pushed to the tip
+			//ofset 11
+			uint16_t count = getIronTimer() / (1000 / 28);
+			if (count > 28)
+				count = 28;
+			OLED_DrawWideChar((count), 6);
+		} else {
+			//Draw in the arrows if the user has the power display turned off
+			if (getIronTimer() == 0
+					&& (temp / 10) > (systemSettings.SolderingTemp / 10)) {
+				//Cooling
+				OLED_DrawSymbol(6, 5);
+			} else {
+				if (getIronTimer() < 1500) {
+					//Maintaining
+					OLED_DrawSymbol(6, 7);
+				} else {		//we are heating
+					OLED_DrawSymbol(6, 6);
+				}
+			}
 		}

 	}
@@ -455,12 +521,12 @@ void DrawUI() {
 	case TEMP_ADJ:
 		//We are prompting the user to change the temp so we draw the current setpoint temp
 		//With the nifty arrows
-		OLED_DrawChar(' ', 0);
-		OLED_DrawChar('<', 1);
+		OLED_DrawChar(' ', 0,0);
+		OLED_DrawChar('<', 1,0);
 		drawTemp(systemSettings.SolderingTemp, 2, 0);
-		OLED_DrawChar(' ', 5);
-		OLED_DrawChar(' ', 7);
-		OLED_DrawChar('>', 6);
+		OLED_DrawChar(' ', 5,0);
+		OLED_DrawChar(' ', 7,0);
+		OLED_DrawChar('>', 6,0);
 		break;
 	case SETTINGS:
 		//We are prompting the user the setting name
@@ -480,7 +546,7 @@ void DrawUI() {
 							+ settingsLongTestScrollPos, lengthLeft);
 			if (lengthLeft < 8)
 				for (uint8_t i = lengthLeft; i < 8; i++)
-					OLED_DrawChar(' ', i);
+					OLED_DrawChar(' ', i, 0);
 			if (millis() - lastOLEDDrawTime > 120) {
 				settingsLongTestScrollPos++;
 				lastOLEDDrawTime = millis();
@@ -489,61 +555,79 @@ void DrawUI() {
 			settingsLongTestScrollPos = 0;
 			switch (settingsPage) {
 			case UVCO:
-				OLED_DrawString("PWRSC ", 6);
+				OLED_DrawString(SettingsShortNames[UVCO], 6);
 				if (systemSettings.cutoutSetting == 0) {
 					//DC
-					OLED_DrawChar('D', 6);
-					OLED_DrawChar('C', 7);
+					OLED_DrawChar('D', 6, 0);
+					OLED_DrawChar('C', 7, 0);
 				} else {
 					//S count
-					OLED_DrawChar('2' + systemSettings.cutoutSetting, 6);
-					OLED_DrawChar('S', 7);
+					OLED_DrawChar('2' + systemSettings.cutoutSetting, 6, 0);
+					OLED_DrawChar('S', 7, 0);
 				}
 				break;
 			case SLEEP_TEMP:
-				OLED_DrawString("STMP ", 5);
+				OLED_DrawString(SettingsShortNames[SLEEP_TEMP], 5);
 				OLED_DrawThreeNumber(systemSettings.SleepTemp / 10, 5);
 				break;
 			case SLEEP_TIME:
-				OLED_DrawString("SLTME ", 6);
-				OLED_DrawTwoNumber(systemSettings.SleepTime, 6);
+				Clear_Screen();
+				OLED_DrawString(SettingsShortNames[SLEEP_TIME], 5);
+				//Draw in the timescale
+				if (systemSettings.SleepTime < 6) {
+					OLED_DrawChar('S', 7, 0);
+					OLED_DrawTwoNumber(systemSettings.SleepTime * 10, 5);
+
+				} else {
+					OLED_DrawChar('M', 7, 0);
+					OLED_DrawTwoNumber(systemSettings.SleepTime - 5, 5);
+				}
 				break;
 			case SHUTDOWN_TIME:
-				OLED_DrawString("SHTME ", 6);
+				OLED_DrawString(SettingsShortNames[SHUTDOWN_TIME], 6);
 				OLED_DrawTwoNumber(systemSettings.ShutdownTime, 6);
 				break;
 			case TEMPDISPLAY:/*Are we showing in C or F ?*/
+				OLED_DrawString(SettingsShortNames[TEMPDISPLAY], 7);
 				if (systemSettings.displayTempInF)
-					OLED_DrawString("TMPUNT F", 8);
+					OLED_DrawChar(SettingTempFChar, 7, 0);
 				else
-					OLED_DrawString("TMPUNT C", 8);
+					OLED_DrawChar(SettingTempCChar, 7, 0);
 				break;
-			case LEFTY:
+			case SCREENROTATION:
+				OLED_DrawString(SettingsShortNames[SCREENROTATION], 7);

-				if (systemSettings.flipDisplay)
-					OLED_DrawString("FLPDSP T", 8);
-				else
-					OLED_DrawString("FLPDSP F", 8);
+				switch (systemSettings.OrientationMode) {
+				case 0:
+					OLED_DrawChar(SettingRightChar, 7, 0);
+					break;
+				case 1:
+					OLED_DrawChar(SettingLeftChar, 7, 0);
+					break;
+				case 2:
+					OLED_DrawChar(SettingAutoChar, 7, 0);
+					break;
+				}
 				break;
 			case MOTIONSENSITIVITY:
-				OLED_DrawString("MSENSE ", 7);
-				OLED_DrawChar('0' + systemSettings.sensitivity, 7);
+				OLED_DrawString(SettingsShortNames[MOTIONSENSITIVITY], 7);
+
+				OLED_DrawChar('0' + systemSettings.sensitivity, 7,0);
 				break;
 			case TEMPROUNDING:
 				//We are prompting the user about their display mode preferences
 			{
+				OLED_DrawString(SettingsShortNames[TEMPROUNDING], 7);
+
 				switch (systemSettings.temperatureRounding) {
 				case ROUNDING_NONE:
-					OLED_DrawString("TMPRND 1", 8);
+					OLED_DrawChar('1', 7,0);
 					break;
 				case ROUNDING_FIVE:
-					OLED_DrawString("TMPRND 5", 8);
+					OLED_DrawChar('5', 7,0);
 					break;
 				case ROUNDING_TEN:
-					OLED_DrawString("TMPRND10", 8);
-					break;
-				default:
-					OLED_DrawString("TMPRND 1", 8);
+					OLED_DrawChar('X', 7,0);
 					break;
 				}
 			}
@@ -551,35 +635,90 @@ void DrawUI() {
 			case DISPUPDATERATE:
 				//We are prompting the user about their display mode preferences
 			{
+				OLED_DrawString(SettingsShortNames[DISPUPDATERATE], 7);
 				switch (systemSettings.displayUpdateSpeed) {
 				case DISPLAYMODE_FAST:
-					OLED_DrawString("TMPSPD F", 8);
+					OLED_DrawChar(SettingFastChar, 7,0);
 					break;
 				case DISPLAYMODE_SLOW:
-					OLED_DrawString("TMPSPD S", 8);
+					OLED_DrawChar(SettingSlowChar, 7,0);
 					break;
 				case DISPLAYMODE_MEDIUM:
-					OLED_DrawString("TMPSPD M", 8);
+					OLED_DrawChar(SettingMediumChar, 7,0);
 					break;

 				}
 			}
 				break;
 			case BOOSTMODE:
+				OLED_DrawString(SettingsShortNames[BOOSTMODE], 7);
+
 				switch (systemSettings.boostModeEnabled) {
 				case 1:
-					OLED_DrawString("BOOST  T", 8);
+					OLED_DrawChar(SettingTrueChar, 7,0);
 					break;
 				case 0:
-					OLED_DrawString("BOOST  F", 8);
+					OLED_DrawChar(SettingFalseChar, 7,0);
 					break;
 				}
 				break;
 			case BOOSTTEMP:
-				OLED_DrawString("BTMP ", 5);
+				OLED_DrawString(SettingsShortNames[BOOSTTEMP], 5);
 				OLED_DrawThreeNumber(systemSettings.BoostTemp / 10, 5);
 				break;
+			case POWERDISPLAY:
+				OLED_DrawString(SettingsShortNames[POWERDISPLAY], 7);
+				switch (systemSettings.powerDisplay) {
+				case 1:
+					OLED_DrawChar(SettingTrueChar, 7,0);
+					break;
+				case 0:
+					OLED_DrawChar(SettingFalseChar, 7,0);
+					break;
+
+				}
+				break;
+			case AUTOSTART:
+				OLED_DrawString(SettingsShortNames[AUTOSTART], 7);
+				switch (systemSettings.autoStart) {
+				case 1:
+					OLED_DrawChar(SettingTrueChar, 7,0);
+					break;
+				case 0:
+					OLED_DrawChar(SettingFalseChar, 7,0);
+					break;
+				case 2:
+					OLED_DrawChar(SettingSleepChar, 7,0);
+					break;
+				}
+				break;
+			case COOLINGBLINK:
+				OLED_DrawString(SettingsShortNames[COOLINGBLINK], 7);
+				switch (systemSettings.coolingTempBlink) {
+				case 1:
+					OLED_DrawChar(SettingTrueChar, 7,0);
+					break;
+				case 0:
+					OLED_DrawChar(SettingFalseChar, 7,0);
+					break;
+				}
+				break;
+#ifdef PIDTUNING
+				case PIDP:
+				OLED_DrawString("PIDP ", 5);
+				OLED_DrawThreeNumber(pidSettings.kp, 5);
+				break;
+				case PIDI:
+				OLED_DrawString("PIDI ", 5);
+				OLED_DrawThreeNumber(pidSettings.ki, 5);
+				break;
+				case PIDD:
+				OLED_DrawString("PIDD ", 5);
+				OLED_DrawThreeNumber(pidSettings.kd, 5);
+				break;
+#endif
 			default:
+
 				break;
 			}
 		}
@@ -587,60 +726,54 @@ void DrawUI() {
 	case SLEEP:
 		//The iron is in sleep temp mode
 		//Draw in temp and sleep
-		OLED_DrawString("SLP", 3);
+		Clear_Screen();
+		OLED_DrawString("SLP ", 4);
 		drawTemp(temp, 4, systemSettings.temperatureRounding);
-		OLED_BlankSlot(84, 96 - 85);		//blank out after the temp
-
-		if (millis() - getLastMovement() > (10 * 60 * 1000)
-				&& (millis() - getLastButtonPress() > (10 * 60 * 1000))) {
-			//OLED off
-			Oled_DisplayOff();
-		} else {
-			Oled_DisplayOn();
-		}
-
+		Oled_DisplayOn();
 		break;
 	case COOLING:
 		//We are warning the user the tip is cooling
-		OLED_DrawString("COOL ", 5);
+		Clear_Screen();
+		OLED_DrawString(CoolingPromptString, 5);
 		temp = readIronTemp(0, 1, 0xFFFF);		//force temp re-reading
-		drawTemp(temp, 5, systemSettings.temperatureRounding);
+
+		if (temp > 500 && systemSettings.coolingTempBlink
+				&& (millis() % 1000) > 500) {
+
+		} else {
+			drawTemp(temp, 5, systemSettings.temperatureRounding);
+		}
+
 		break;
 	case UVLOWARN:
-		OLED_DrawString("LOW VOLT", 8);
+		OLED_DrawString(UVLOWarningString, 8);
 		break;
 	case THERMOMETER:
 		temp = readIronTemp(0, 1, 0xFFFF);	//Force a reading as heater is off
-		OLED_DrawString("TEMP ", 5);//extra one to it clears the leftover 'L' from IDLE
+		OLED_DrawString("Temp ", 5);//extra one to it clears the leftover 'L' from IDLE
 		drawTemp(temp, 5, 0);
 		break;
 	case DCINDISP: {
 		uint16_t voltage = readDCVoltage(systemSettings.voltageDiv); //get X10 voltage

 		if (StatusFlags == 0 || ((millis() % 1000) > 500)) {
+
 			OLED_DrawString("IN", 2);
-			OLED_DrawChar((voltage / 100) % 10, 2);
+			OLED_DrawChar(48 + ((voltage / 100) % 10), 2,0);
 			voltage -= (voltage / 100) * 100;
-			OLED_DrawChar((voltage / 10) % 10, 3);
+			OLED_DrawChar(48 + ((voltage / 10) % 10), 3,0);
 			voltage -= (voltage / 10) * 10;
-			OLED_DrawChar('.', 4);
-			OLED_DrawChar(voltage % 10, 5);
-			OLED_DrawChar('V', 6);
-			OLED_DrawChar(' ', 7);
+			OLED_DrawChar('.', 4,0);
+			OLED_DrawChar(48 + (voltage % 10), 5,0);
+			OLED_DrawChar('V', 6,0);
+			OLED_DrawChar(' ', 7,0);
 		} else {
 			OLED_DrawString("IN      ", 8);
 		}
 	}
 		break;
 	case TEMPCAL: {
-
-		if (StatusFlags == 0) {
-			OLED_DrawString("CAL TEMP", 8);
-		} else if (StatusFlags == 1) {
-			OLED_DrawString("CAL OK  ", 8);
-		} else if (StatusFlags == 2) {
-			OLED_DrawString("CAL FAIL", 8);
-		}
+		OLED_DrawString(TempCalStatus[StatusFlags], 8);
 	}

 		break;
--- a/workspace/ts100/src/Oled.c
+++ b/workspace/ts100/src/Oled.c
@@ -14,10 +14,15 @@

 #include "Font.h"
 int8_t displayOffset = 32;
+uint8_t currentOrientation = 0;
+
+uint8_t displayBuffer[2 * 96]; //This is used to allow us to draw locally before sync'ing to the screen.
+
 /*Setup params for the OLED screen*/
 /*http://www.displayfuture.com/Display/datasheet/controller/SSD1307.pdf*/
 /*All commands are prefixed with 0x80*/
-u8 OLED_Setup_Array[46] = { 0x80, 0xAE,/*Display off*/
+u8 OLED_Setup_Array[46] = { /**/
+0x80, 0xAE,/*Display off*/
 0x80, 0xD5,/*Set display clock divide ratio / osc freq*/
 0x80, 0x52,/*Unknown*/
 0x80, 0xA8,/*Set Multiplex Ratio*/
@@ -41,53 +46,61 @@ u8 OLED_Setup_Array[46] = { 0x80, 0xAE,/*Display off*/
 0x80, 0XA6,/*Normal display*/
 0x80, 0xAF /*Dispaly on*/
 };
-
+uint8_t OLEDOnOffState = 0; //Used to lock out so we dont send it too often
 /*
 Function: Oled_DisplayOn
 Description:Turn on the Oled display
 */
 void Oled_DisplayOn(void) {
-	u8 data[6] = { 0x80, 0X8D, 0x80, 0X14, 0x80, 0XAF };
+	if (OLEDOnOffState != 1) {
+		u8 data[6] = { 0x80, 0X8D, 0x80, 0X14, 0x80, 0XAF };

-	I2C_PageWrite(data, 6, DEVICEADDR_OLED);
+		I2C_PageWrite(data, 6, DEVICEADDR_OLED);
+		OLEDOnOffState = 1;
+	}
 }
 /*
 Function: Oled_DisplayOff
 Description:Turn off the Oled display
 */
 void Oled_DisplayOff(void) {
-	u8 data[6] = { 0x80, 0X8D, 0x80, 0X10, 0x80, 0XAE };
+	if (OLEDOnOffState != 2) {
+		u8 data[6] = { 0x80, 0X8D, 0x80, 0X10, 0x80, 0XAE };

-	I2C_PageWrite(data, 6, DEVICEADDR_OLED);
+		I2C_PageWrite(data, 6, DEVICEADDR_OLED);
+		OLEDOnOffState = 2;
+	}
 }
-/*
- * This sets the OLED screen to invert the screen (flip it vertically)
- * This is used if the unit is set to left hand mode
- */
-void Oled_DisplayFlip() {
-	u8 data[2] = { 0x80, 0XC8 };
-	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
-	data[1] = 0xA1;
-	I2C_PageWrite(data, 2, DEVICEADDR_OLED);
-	displayOffset = 0;

-}
 /*
 Description: write a command to the Oled display
 Input: number of bytes to write, array to write
 Output:
 */
-const u8* Data_Command(u8 length,const u8* data) {
+const u8* Data_Command(u8 length, const u8* data) {
 	int i;
 	u8 tx_data[129];
 	//here are are inserting the data write command at the beginning
 	tx_data[0] = 0x40;
 	length++;
-	for (i = 1; i < length; i++) //Loop through the array of data
-		tx_data[i] = *data++;
+	for (i = 1; i <= length; i++) //Loop through the array of data
+			{
+		if (data == 0)
+			tx_data[i] = 0;
+		else
+			tx_data[i] = *data++;
+	}
 	I2C_PageWrite(tx_data, length, DEVICEADDR_OLED); //write out the buffer
 	return data;
 }
+//This causes us to write out the buffered screen data to the display
+void OLED_Sync() {
+	Set_ShowPos(0, 0);
+	Data_Command(96, displayBuffer);
+	Set_ShowPos(0, 1);
+	Data_Command(96, displayBuffer + 96);
+
+}
 /*******************************************************************************
 Function:Set_ShowPos
 Description:Set the current position in GRAM that we are drawing to
@@ -107,27 +120,26 @@ void Set_ShowPos(u8 x, u8 y) {
 Inputs:(x,y) start point, (width,height) of enclosing rect, pointer to data
 Output: pointer to the last byte written out
 *******************************************************************************/
-const u8* Oled_DrawArea(u8 x0, u8 y0, u8 wide, u8 high,const u8* ptr) {
-	u8 m, n, y;
-
-	n = y0 + high;
-	if (y0 % 8 == 0)
-		m = y0 / 8;
-	else
-		m = y0 / 8 + 1;
-
-	if (n % 8 == 0)
-		y = n / 8;
-	else
-		y = n / 8 + 1;
-
-	for (; m < y; m++) {
-		Set_ShowPos(x0, m);
-		ptr = Data_Command(wide, ptr);
+void Oled_DrawArea(u8 x, u8 y, u8 wide, u8 height, const u8* ptr) {
+	//We want to blat the given data over the buffer
+	//X is the left right position (index's through the display buffer)
+	//Y is the height value (affects the bits)
+	//Y is either 0 or 8, we dont do smaller bit blatting
+	u8 lines = height / 8;
+	//We draw the 1 or two stripes seperately
+	for (u8 i = 0; i < (wide * lines); i++) {
+		u8 xp = x + (i % wide);
+		u8 yoffset = i < wide ? 0 : 96;
+		if (y == 8)
+			yoffset = 96;
+		displayBuffer[xp + yoffset] = ptr[i];
 	}
-	return ptr;
-}

+}
+void OLED_InvertBuffer() {
+	for (uint16_t i = 0; i < (2 * 96); i++)
+		displayBuffer[i] = ~displayBuffer[i];
+}
 /*******************************************************************************
 Function:GPIO_Init_OLED
 Description:Init the outputs as needed for the OLED (in this case the RST line)
@@ -145,19 +157,26 @@ void GPIO_Init_OLED(void) {
 Description: Initializes the Oled screen
 *******************************************************************************/
 void Init_Oled(uint8_t leftHanded) {
-	u8 param_len;

+	currentOrientation = leftHanded;
+	u8 param_len;
 	OLED_RST();
 	delayMs(5);
 	OLED_ACT(); //Toggling reset to reset the oled
 	delayMs(5);
 	param_len = 46;
-	if (leftHanded) {
+	if (leftHanded == 1) {
 		OLED_Setup_Array[11] = 0xC8;
 		OLED_Setup_Array[19] = 0xA1;
 		displayOffset = 0;
+	} else if (leftHanded == 0) {
+		OLED_Setup_Array[11] = 0xC0;
+		OLED_Setup_Array[19] = 0x40;
+		displayOffset = 32;
 	}
 	I2C_PageWrite((u8 *) OLED_Setup_Array, param_len, DEVICEADDR_OLED);
+	for (uint8_t i = 0; i < 2 * 96; i++)
+		displayBuffer[i] = 0; //turn off screen
 }

 /*******************************************************************************
@@ -165,57 +184,68 @@ void Init_Oled(uint8_t leftHanded) {
 Description:Clear the entire screen to off (black)
 *******************************************************************************/
 void Clear_Screen(void) {
-	u8 tx_data[128];
-	memset(tx_data, 0, 128);
-	for (u8 i = 0; i < 2; i++) {
-		Oled_DrawArea(0, i * 8, 128, 8, tx_data);
-	}
+	memset(displayBuffer, 0, 96 * 2);
+
 }
 /*
 * Draws a string onto the screen starting at the left
 */
 void OLED_DrawString(const char* string, const uint8_t length) {
 	for (uint8_t i = 0; i < length; i++) {
-		OLED_DrawChar(string[i], i);
+		if (string[i] >= 0x80) {
+			OLED_DrawChar(string[i + 1], i, string[i]);
+			i++;
+			OLED_DrawChar(' ', i,0);
+		} else
+			OLED_DrawChar(string[i], i, '\0');
+
 	}
 }
 /*
 * Draw a char onscreen at letter index x
 */
-void OLED_DrawChar(char c, uint8_t x) {
+void OLED_DrawChar(char c, uint8_t x, char preCursor) {
 	if (x > 7)
 		return; //clipping
-	x *= FONT_WIDTH; //convert to a x coordinate

-	u8* ptr = (u8*) FONT;
-	if (c >= 'a' && c <= 'z') {
-		ptr += (c - 'a' + 10) * (FONT_WIDTH * 2); //alpha is ofset 10 chars into the array
-	} else if (c >= 'A' && c <= 'Z') {
-		ptr += (c - 'A' + 10) * (FONT_WIDTH * 2); //alpha is ofset 10 chars into the array
-	} else if (c >= '0' && c <= '9')
-		ptr += (c - '0') * (FONT_WIDTH * 2);
-	else if (c < 10)
-		ptr += (c) * (FONT_WIDTH * 2);
-	else if (c == ' ') {
-		//blank on space bar
-		ptr += (36) * (FONT_WIDTH * 2);
-	} else if (c == '<') {
-		ptr += (37) * (FONT_WIDTH * 2);
-	} else if (c == '>') {
-		ptr += (38) * (FONT_WIDTH * 2);
-	} else if (c == '.') {
-		ptr += (39) * (FONT_WIDTH * 2);
-	}
+	x *= FONT_WIDTH; //convert to a x coordinate
+	u8* ptr;
+	u16 offset = 0;
+	if (c < 0x80) {
+		ptr = (u8*) FONT;
+		offset = c - ' ';
+	} else if (preCursor>0) {
+		ptr = (u8*) FontLatin2;
+		offset = c - 0xA0+0x40; //this table starts at 0xA0
+	} else
+		return; //not in font
+
+	offset *= (2 * FONT_WIDTH);
+	ptr += offset;

 	Oled_DrawArea(x, 0, FONT_WIDTH, 16, (u8*) ptr);
 }
-void OLED_DrawExtendedChar(uint8_t id, uint8_t x) {
-	u8* ptr = (u8*) extendedFont;
+void OLED_DrawExtraFontChars(uint8_t id, uint8_t x) {
+	u8* ptr = (u8*) ExtraFontChars;
+	ptr += (id) * (FONT_WIDTH * 2);
+	x *= FONT_WIDTH; //convert to a x coordinate
+	Oled_DrawArea(x, 0, FONT_WIDTH, 16, (u8*) ptr);
+}
+void OLED_DrawSymbolChar(uint8_t id, uint8_t x) {
+	u8* ptr = (u8*) FontSymbols;
 	ptr += (id) * (FONT_WIDTH * 2);
 	x *= FONT_WIDTH; //convert to a x coordinate

 	Oled_DrawArea(x, 0, FONT_WIDTH, 16, (u8*) ptr);
 }
+
+void OLED_DrawWideChar(uint8_t id, uint8_t x) {
+	u8* ptr = (u8*) DoubleWidthChars;
+	ptr += (id) * (FONT_WIDTH * 4);
+	x *= FONT_WIDTH; //convert to a x coordinate
+
+	Oled_DrawArea(x, 0, FONT_WIDTH * 2, 16, (u8*) ptr);
+}
 void OLED_BlankSlot(uint8_t xStart, uint8_t width) {
 	u8* ptr = (u8*) FONT;
 	ptr += (36) * (FONT_WIDTH * 2);
@@ -228,27 +258,27 @@ void OLED_BlankSlot(uint8_t xStart, uint8_t width) {
 */
 void OLED_DrawTwoNumber(uint8_t in, uint8_t x) {

-	OLED_DrawChar((in / 10) % 10, x);
-	OLED_DrawChar(in % 10, x + 1);
+	OLED_DrawChar(48 + (in / 10) % 10, x,0);
+	OLED_DrawChar(48 + in % 10, x + 1,0);
 }
 /*
 * Draw a 3 digit number to the display at letter slot x
 */
 void OLED_DrawThreeNumber(uint16_t in, uint8_t x) {

-	OLED_DrawChar((in / 100) % 10, x);
-	OLED_DrawChar((in / 10) % 10, x + 1);
-	OLED_DrawChar(in % 10, x + 2);
+	OLED_DrawChar(48 + (in / 100) % 10, x,0);
+	OLED_DrawChar(48 + (in / 10) % 10, x + 1,0);
+	OLED_DrawChar(48 + in % 10, x + 2,0);
 }
 /*
 * Draw a 4 digit number to the display at letter slot x
 */
 void OLED_DrawFourNumber(uint16_t in, uint8_t x) {

-	OLED_DrawChar((in / 1000) % 10, x);
-	OLED_DrawChar((in / 100) % 10, x + 1);
-	OLED_DrawChar((in / 10) % 10, x + 2);
-	OLED_DrawChar(in % 10, x + 3);
+	OLED_DrawChar(48 + (in / 1000) % 10, x,0);
+	OLED_DrawChar(48 + (in / 100) % 10, x + 1,0);
+	OLED_DrawChar(48 + (in / 10) % 10, x + 2,0);
+	OLED_DrawChar(48 + (in % 10), x + 3,0);
 }

 void OLED_DrawIDLELogo() {
@@ -274,3 +304,15 @@ void OLED_DrawIDLELogo() {
 void OLED_DrawSymbol(uint8_t x, uint8_t symbol) {
 	Oled_DrawArea(x * FONT_WIDTH, 0, 16, 16, SymbolTable + (symbol * 32));
 }
+
+void OLED_SetOrientation(uint8_t ori) {
+	if (ori > 1)
+		return;
+	if (ori != currentOrientation) {
+		Init_Oled(ori);
+	}
+}
+
+uint8_t OLED_GetOrientation() {
+	return currentOrientation;
+}
--- a/workspace/ts100/src/PID.c
+++ b/workspace/ts100/src/PID.c
@@ -7,35 +7,40 @@

 #include "PID.h"
 #define MAXPIDOUTPUT 50000
+//MAXPIDOUTPUT is the maximum time duration we can support for the irons output, as anything longer than this will be cut off by the next PID iteration
+
+pidSettingsType pidSettings;
+
 //This function computes the new value for the ON time of the system
 //This is the return value from this function
 int32_t computePID(uint16_t setpoint) {
-	int32_t ITerm = 0;
-	static int16_t lastReading = 0;
-	uint16_t currentReading = readIronTemp(0, 1,setpoint); //get the current temp of the iron
+	static int32_t ITerm = 0; //Used to store the integral error
+	static int16_t lastError = 0;
+	uint16_t currentReading = readIronTemp(0, 1, setpoint); //get the current temp of the iron
 	int16_t error = (int16_t) setpoint - (int16_t) currentReading; //calculate the error term
-	ITerm += (pidSettings.ki * error);
-	if (ITerm > MAXPIDOUTPUT/2)
-		ITerm = MAXPIDOUTPUT/2;
-	else if (ITerm < 0)
-		ITerm = 0; //cap at 0 since we cant force the iron to cool itself :)
+	int16_t DInput = (error - lastError) / 10; //compute the input to the D term

-	int16_t DInput = (currentReading - lastReading); //compute the input to the D term
-	int32_t output = (pidSettings.kp * error) + (ITerm)
+	ITerm += ((error) / 20);
+	if (ITerm > 300)
+		ITerm = 0; //Prevents this accumulating too much during inital heatup
+	else if (ITerm < 0)
+		ITerm = 0; //Cap at 0 as we can't force cool
+	if (DInput > 1000)
+		DInput = 0;
+	int32_t output = (pidSettings.kp * error) + (ITerm * pidSettings.ki)
 			- (pidSettings.kd * DInput);
 	if (output > MAXPIDOUTPUT)
 		output = MAXPIDOUTPUT;
 	else if (output < 0)
 		output = 0;
-
-	lastReading = currentReading; //storing values for next iteration of the loop
+	lastError = error;
 	return output;

 }
-/*Sets up the pid values*/
+/*Sets up the pid values to  defaults*/
 void setupPID(void) {
-	pidSettings.kp = 15;
-	pidSettings.ki = 2;
-	pidSettings.kd = 3;
+	pidSettings.kp = 8;
+	pidSettings.ki = 1;
+	pidSettings.kd = 0; //Not using D atm

 }
--- a/workspace/ts100/src/Settings.c
+++ b/workspace/ts100/src/Settings.c
@@ -10,6 +10,9 @@
 #include "Settings.h"
 #define FLASH_ADDR 		(0x8000000|0xBC00)/*Flash start OR'ed with the maximum amount of flash - 1024 bytes*/
 #define FLASH_LOGOADDR 	(0x8000000|0xB800) /*second last page of flash set aside for logo image*/
+
+systemSettingsType systemSettings;
+
 void saveSettings() {
 	//First we erase the flash
 	FLASH_Unlock(); //unlock flash writing
@@ -35,7 +38,6 @@ void restoreSettings() {
 	if (systemSettings.version != SETTINGSVERSION) {
 		//probably not setup
 		resetSettings();
-		saveSettings();
 	}

 }
@@ -56,13 +58,13 @@ uint8_t lookupVoltageLevel(uint8_t level) {
 void resetSettings() {

 	systemSettings.SleepTemp = 1500;//Temperature the iron sleeps at - default 150.0 C
-	systemSettings.SleepTime = 1;//How many minutes we wait until going to sleep - default 1 min
+	systemSettings.SleepTime = 6;//How many seconds/minutes we wait until going to sleep - default 1 min
 	systemSettings.SolderingTemp = 3200;	//Default soldering temp is 320.0 C
 	systemSettings.cutoutSetting = 0;			//default to no cut-off voltage
 	systemSettings.version = SETTINGSVERSION;//Store the version number to allow for easier upgrades
 	systemSettings.displayTempInF = 0;			//default to C
-	systemSettings.flipDisplay = 0;				//Default to right handed mode
-	systemSettings.sensitivity = 6;				//Default high sensitivity
+	systemSettings.OrientationMode = 2;				//Default to automatic
+	systemSettings.sensitivity = 7;				//Default high sensitivity
 	systemSettings.tempCalibration = 239;	//Default to their calibration value
 	systemSettings.voltageDiv = 144;			//Default divider from schematic
 	systemSettings.ShutdownTime = 30;//How many minutes until the unit turns itself off
@@ -70,6 +72,10 @@ void resetSettings() {
 	systemSettings.temperatureRounding = 0;	//How the temperature is rounded off
 	systemSettings.boostModeEnabled = 0;//Default to safe, with no boost mode
 	systemSettings.BoostTemp = 4000;				//default to 400C
+	systemSettings.powerDisplay = 0;		//default to power display being off
+	systemSettings.autoStart = 0;				//Auto start off for safety
+	systemSettings.coolingTempBlink = 0;		//Blink the temperature on the cooling screen when its > 50C
+	saveSettings();
 }

 void showBootLogoIfavailable() {
@@ -87,16 +93,16 @@ void showBootLogoIfavailable() {

 	}
 	/*char hex[] = { '0', '1', '2', '3', '4', '5', '6', '7', '8', '9', 'A', 'B',
-			'C', 'D', 'E', 'F' };
+	 'C', 'D', 'E', 'F' };

-	OLED_DrawChar(hex[(temp8[0] >> 4) & 0x0F], 0);
-	OLED_DrawChar(hex[(temp8[0] >> 0) & 0x0F], 1);
-	OLED_DrawChar(hex[(temp8[1] >> 4) & 0x0F], 2);
-	OLED_DrawChar(hex[(temp8[1] >> 0) & 0x0F], 3);
-	OLED_DrawChar(hex[(temp8[2] >> 4) & 0x0F], 4);
-	OLED_DrawChar(hex[(temp8[2] >> 0) & 0x0F], 5);
-	OLED_DrawChar(hex[(temp8[3] >> 4) & 0x0F], 6);
-	OLED_DrawChar(hex[(temp8[3] >> 0) & 0x0F], 7);*/
+	 OLED_DrawChar(hex[(temp8[0] >> 4) & 0x0F], 0);
+	 OLED_DrawChar(hex[(temp8[0] >> 0) & 0x0F], 1);
+	 OLED_DrawChar(hex[(temp8[1] >> 4) & 0x0F], 2);
+	 OLED_DrawChar(hex[(temp8[1] >> 0) & 0x0F], 3);
+	 OLED_DrawChar(hex[(temp8[2] >> 4) & 0x0F], 4);
+	 OLED_DrawChar(hex[(temp8[2] >> 0) & 0x0F], 5);
+	 OLED_DrawChar(hex[(temp8[3] >> 4) & 0x0F], 6);
+	 OLED_DrawChar(hex[(temp8[3] >> 0) & 0x0F], 7);*/
 	if (temp8[0] != 0xAA)
 		return;
 	if (temp8[1] != 0x55)
@@ -106,8 +112,7 @@ void showBootLogoIfavailable() {
 	if (temp8[3] != 0x0D)
 		return;

-
 	Oled_DrawArea(0, 0, 96, 16, (uint8_t*) (temp8 + 4));
-
+	OLED_Sync();
 	delayMs(1000);
 }
--- a/workspace/ts100/src/Strings.c
+++ b/workspace/ts100/src/Strings.c
@@ -0,0 +1,186 @@
+/*
+ * Strings.c
+ *
+ *  Created on: 5Aug.,2017
+ *      Author: Ben V. Brown
+ */
+#include "Strings.h"
+#define LANG_IT
+#ifdef LANG_EN
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Power source. Sets cutoff voltage. <DC=10V S=3.3V per cell>",
+    "      Sleep Temperature <C>",
+    "      Sleep Timeout <Minutes>",
+    "      Shutdown Timeout <Minutes>",
+    "      Motion Sensitivity <0=Off 1=Least sensitive 9=Most sensitive>",
+    "      Temperature Unit <C=Celsius F=Farnheit>",
+    "      Temperature Rounding Amount <Units>",
+    "      Temperature Display Update Rate <S=Slow M=Medium F=Fast>",
+    "      Display Orientation <A=Automatic L=Left Handed R=Right Handed>",
+    "      Enable front key enters boost mode 450C mode when soldering <T=True F=False>",
+    "      Temperature when in \"boost\" mode <C>",
+    "      Changes the arrows to a power display when soldering <T=True F=False>",
+    "      Automatically starts the iron into soldering on power up. <T=Soldering S=Sleep mode F=Off>",
+    "      Blink the temperature on the cooling screen while the tip is still hot. <T=True F=False>"
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fail" }; //All fixed 8 chars
+  const char* UVLOWarningString = "Low Volt"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Off  "; //Fixed width 5 chars
+  const char SettingTrueChar = 'T';
+  const char SettingFalseChar = 'F';
+  const char SettingSleepChar = 'S';
+  const char SettingFastChar = 'F';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'S';
+  const char SettingRightChar = 'R';
+  const char SettingLeftChar = 'L';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
+
+#ifdef LANG_ES
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Fuente de energía. Ajusta el límite inferior de voltaje. <DC=10V S=3.3V por celda>",
+    "      Temperatura en reposo. <C>",
+    "      Tiempo hasta activar reposo. <Minutos>",
+    "      Tiempo hasta apagado. <Minutos>",
+    "      Sensibilidad del movimiento. <0=Apagado 1=El menos sensible 9=El más sensible>",
+    "      Unidad de temperatura.",
+    "      Redondeo de la temperatura.",
+    "      Tasa de actualización de la temperatura.",
+    "      Orientación de la pantalla <A=Automático I=Mano izquierda D=Mano derecha>",
+    "      Activar el botón \"Boost\" en modo soldadura.",
+    "      Temperatura en modo \"Boost\". <C>",
+    "      Cambiar las flechas en pantalla por indicador de potencia en modo soldadura.",
+    "      Iniciar modo soldadura en el encendido. <V=Sí S=Modo reposo F=No>",
+    "      Parpadea la temperatura en el enfriamiento si la punta sigue caliente."
+  };
+  const char* TempCalStatus[3] = {"CAL TEMP", "CAL OK  ", "CAL FAIL"}; //All fixed 8 chars
+  const char* UVLOWarningString = "LOW VOLT"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Cool "; //Fixed width 5 chars
+  const char SettingTrueChar = 'V';
+  const char SettingFalseChar = 'F';
+  const char SettingSleepChar = 'S';
+  const char SettingFastChar = 'R';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'I';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
+
+#ifdef LANG_DE
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Stromversorgung. Setzt Abschaltspannung <DC=10V S=3.3V pro Zelle>",
+    "      Ruhetemperatur <C>",
+    "      Ruhemodus nach <Minuten>",
+    "      Abschaltzeit <Minuten>",
+    "      Bewegungsempfindlichkeit <0=Aus 1=Minimal 9=Maximal>",
+    "      Temperatur Einheit",
+    "      Temperatur Runden",
+    "      Temperaturanzeige Updaterate",
+    "      Anzeigerichtung <A=Auto L=Linkshändig R=Rechtshändig>",
+    "      Fronttaste für Temperaturboost einschalten",
+    "      Temperatur im \"boost\"-Modus <C>",
+    "      Ändert \"Temperaturpfeile\" in Leistungsbalken",
+    "      Automatischer Start beim Einschalten. <J=Löttemp R=Ruhemodus N=Aus>",
+    "      Temperatur blinkt beim Abkühlen, solange noch heiß."
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Fehl" }; //All fixed 8 chars
+  const char* UVLOWarningString = "V gering"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Kalt "; //Fixed width 5 chars
+  const char SettingTrueChar = 'J';
+  const char SettingFalseChar = 'N';
+  const char SettingSleepChar = 'R';
+  const char SettingFastChar = 'S';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'R';
+  const char SettingLeftChar = 'L';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
+
+#ifdef LANG_FR
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Type d\'alimentation. Regle la tension de coupure. <DC=10V S=3.3V par cellules>",
+    "      Temperature en veille. <C>",
+    "      Temps avant mise en veille. <Minutes>",
+    "      Temps avant extinction. <Minutes>",
+    "      Sensibilitee du capteur de mouvement. <0=Inactif 1=Peu sensible 9=Tres sensible>",
+    "      Unitee de temperature.",
+    "      Arrondissement de la temperature.",
+    "      Taux de raffraichissement de la temperature.",
+    "      Orientation de l\'affichage. <A=Automatique G=Gaucher D=Droitier>",
+    "      Active le mode \"Boost\" 450C sur le bouton de devant pendant la soudure.",
+    "      Temperature du mode \"Boost\". <C>",
+    "      Change les fleches en affichage de la tension pendant la soudure.",
+    "      Demarre automatiquement la soudure a l\'allumage. <A=Active, V=Mode Veille, D=Desactive>",
+    "      Fait clignotter la temperature pendant la phase de refroidissement quand la panne est chaude."
+  };
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Err " }; //All fixed 8 chars
+  const char* UVLOWarningString = "Batt Bas"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Etein"; //Fixed width 5 chars
+  const char SettingTrueChar = 'A';
+  const char SettingFalseChar = 'D';
+  const char SettingSleepChar = 'V';
+  const char SettingFastChar = 'R';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'G';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
+
+#ifdef LANG_IT
+  const char* SettingsLongNames[14] = {
+    /*These are all the help text for all the settings.*/
+    /*All must start with 6 spaces so they come on screen nicely.*/
+    "      Sorgente di alimentazione. Imposta il limite inferiore di tensione. <DC=10V S=3.3V per cella>",
+    "      Temperatura modalità riposo <C>",
+    "      Timeout per passaggio a modalità riposo <Minuti>",
+    "      Timeout spegnimento <Minuti>",
+    "      Sensibilità al movimento <0=Spento 1=Sensibilità minima 9=Sensibilità massima>",
+    "      Unità di temperatura",
+    "      Arrotondamento temperatura",
+    "      Velocità di aggiornamento temperatura",
+    "      Orientamento del display <A=Automatico S=Sinistrorso D=Destrorso>",
+    "      Il tasto anteriore abilita modalità \"boost\" fino a 450C durante la saldatura",
+    "      Temperatura in modalità \"boost\" <C>",
+    "      Visualizza il grafico della potenza assorbita al posto delle frecce",
+    "      Avvia automaticamente il saldatore quando viene alimentato. <S=Modalità saldatura R=Modalità riposo N=Spento>",
+    "      Durante lo spegnimento la temperatura lampeggia sul display finché la punta è calda."
+  };
+
+  const char* TempCalStatus[3] = { "Cal Temp", "Cal OK  ", "Cal Err " }; //All fixed 8 chars
+  const char* UVLOWarningString = "LOW VOLT"; //Fixed width 8 chars
+  const char* CoolingPromptString = "Cool"; //Fixed width 5 chars
+  const char SettingTrueChar = 'S';
+  const char SettingFalseChar = 'N';
+  const char SettingSleepChar = 'R';
+  const char SettingFastChar = 'V';
+  const char SettingMediumChar = 'M';
+  const char SettingSlowChar = 'L';
+  const char SettingRightChar = 'D';
+  const char SettingLeftChar = 'S';
+  const char SettingAutoChar = 'A';
+  const char SettingTempCChar = 'C';
+  const char SettingTempFChar = 'F';
+#endif
+const char* SettingsShortNames[14] = { "PWRSC ", "STMP ", "STME ", "SHTME ",
+		"MSENSE ", "TMPUNT ", "TMPRND ", "TMPSPD ", "DSPROT ", "BOOST  ",
+		"BTMP ", "PWRDSP ", "ASTART ", "CLBLNK " };
Author	SHA1	Message	Date
Ben V. Brown	0e7e304f4e	Patch to handle UTF slightly better. Not perfect but working for now	2017-09-17 12:21:25 +10:00
Ben V. Brown	0aae546dc9	Update strings to be more uniform closes #89 Also includes the new Italian translation closes #88	2017-09-17 11:50:44 +10:00
Maelremrem	2bf06caa09	Added french language (#84 ) * Added french language Add the french translation for all the strings <maelremrem>	2017-09-09 23:13:21 +10:00
thanks4opensource	c1ab76260f	Python version of Logo Editor/TS100 Logo Editor (#78 )	2017-08-29 20:06:00 +10:00
Ben V. Brown	6cc2dfe238	Fix jumping into cooldown accidentally Final commit for 1.17	2017-08-26 16:54:09 +10:00
Ben V. Brown	0ae32506e9	Fix the blinking display on cooling screen	2017-08-23 13:15:01 +10:00
Ben V. Brown	bb174c7639	Fix #62	2017-08-13 22:47:01 +10:00
Ben V. Brown	1d602bd9a1	Add display inversion for cooling	2017-08-13 12:48:16 +10:00
Ben V. Brown	a9da6d511b	Add German #60	2017-08-13 12:39:04 +10:00
Ben V. Brown	4f0e3560b9	Fix #62	2017-08-13 12:36:00 +10:00
Ben V. Brown	8b112e7f7d	Add little C and F logos & arrow for boost	2017-08-11 17:04:09 +10:00
Ben V. Brown	37f36b960c	Merge branch 'master' of https://github.com/Ralim/ts100	2017-08-11 16:31:10 +10:00
Ben V. Brown	c5c1171112	Fix font erroring char. Add accel lockout for autostart. Helps for the following issues: #51 #38	2017-08-11 16:31:04 +10:00
Ben V. Brown	109b3436e6	Update README.md	2017-08-11 14:51:51 +10:00
Ben V. Brown	088b98c131	Update README.md	2017-08-11 14:25:04 +10:00
Ben V. Brown	ea1b0e2ae3	Link in latin extended font	2017-08-11 14:20:41 +10:00
Ben V. Brown	92ee55ebd5	Annotate font table	2017-08-11 14:06:26 +10:00
Ben V. Brown	f0e1498e92	Fix screen blink Fixes #56	2017-08-10 17:34:01 +10:00
Ángel González	6c56f98928	Translated strings to es_ES (#55 ) Thanks to @Aglezabad	2017-08-09 19:52:01 +10:00
Ben V. Brown	d2efa0dc05	Add early exit to settings menu Adds pressing both buttons to exit settings menu. #53	2017-08-09 15:14:06 +10:00
Ben V. Brown	f3c1fafccc	Documentation cleanup	2017-08-09 10:34:24 +10:00
Ben V. Brown	220775ed1f	Merge branch 'master' of https://github.com/Ralim/ts100	2017-08-09 10:28:54 +10:00
Ben V. Brown	c3d672c0dd	Adding in lower sleep times #46 Adding in smaller times for sleep	2017-08-09 10:28:51 +10:00
Alex Wigen	57c0bf4dc1	Fix typo in Linux flasher script (#49 )	2017-08-09 10:13:18 +10:00
Ben V. Brown	9969c66520	Add ability to start into sleep	2017-08-09 10:07:34 +10:00
Ben V. Brown	8cc7d452ce	Adjust key timings & patch flashing Patch to help improve #52 Fixes #50	2017-08-09 10:01:38 +10:00
Ben V. Brown	c0f2a4991a	Add blinking temp Adds blinking temp #39	2017-08-08 21:00:41 +10:00
Ben V. Brown	1822cece90	Massively better font Moved to a newer font. First stage of improving screen	2017-08-08 18:09:07 +10:00
Ben V. Brown	42e6818114	Convert IMU to IRQ for rotation This moves the rotation detection to use the IRQ2 line. Fixes #44	2017-08-08 16:38:21 +10:00
Ben V. Brown	a10947cdac	Moving more text into strings.c/.h	2017-08-08 10:49:15 +10:00
Ben V. Brown	48040acbcc	Add autostart Adds autostart option. Only works on first power up, so if the settings wrong you can still easily change it 😄 Fixes #43	2017-08-06 22:21:57 +10:00
Ben V. Brown	f1aa331168	Converted menu over to strings.h mostly	2017-08-06 20:41:34 +10:00
Ben V. Brown	de0059bd08	Moving strings (more)	2017-08-05 22:51:54 +10:00
Alex Wigen	f8f20bee5c	Add flash script for Linux (#40 ) * Add flash script for Linux * Add credit and link to github	2017-08-05 20:34:43 +10:00
Ben V. Brown	90599a8ae6	Retune PID, improve response rate slightly. (But slightly more oscillation)	2017-08-02 21:38:42 +10:00
Ben V. Brown	b0264be3c5	Better button auto-repeat	2017-07-30 21:25:27 +10:00
Ben V. Brown	4fb7a70e3c	More explicit left handed checks	2017-07-30 20:02:58 +10:00
Ben V. Brown	535a1b3aa9	Making the auto-flip less sensitive #34	2017-07-27 20:29:17 +10:00
Ben V. Brown	5a26bf413a	Update README.md	2017-07-27 11:52:28 +10:00
Ben V. Brown	1cbcba924f	Adding auto-rotation to the screen Adds auto rotation support using the proper orientation detection. (Not using raw values). Should Fix and close #29	2017-07-27 11:46:04 +10:00
Ben V. Brown	af9b8dca29	Working rough indicator of power	2017-07-26 22:05:54 +10:00
Ben V. Brown	965a0890cb	Add toggle for power display	2017-07-26 09:47:26 +10:00
mkninc	2e823b6594	Quick fix for multiple definition of structs (#33 )	2017-07-26 09:18:41 +10:00
Ben V. Brown	56f31b02aa	pre-work for power display	2017-07-26 09:18:07 +10:00
Ben V. Brown	2d260bd62c	Add youtube link	2017-07-25 10:08:01 +10:00
Ben V. Brown	379eb68ce4	Update README.md	2017-07-25 09:48:22 +10:00
Ben V. Brown	f077c0241f	Fix order of definitions for some variables	2017-07-25 08:28:33 +10:00
Ben V. Brown	7bedad5d51	Fix readme error	2017-07-24 23:08:08 +10:00
Ben V. Brown	8a503f84e2	Cleaning up files Fixing warnings Add powerDisplayToggle	2017-07-24 23:03:56 +10:00
Ben V. Brown	f89fd5c651	Merge branch 'master' of github.com:Ralim/ts100	2017-07-24 22:55:49 +10:00
Ben V. Brown	3983bf8590	Fix buttons in left handed mode when user is changing the temperature. As pointed out in #29 Clear the leftover temperature unit on the sleep screen.	2017-07-24 22:54:30 +10:00
Ben V. Brown	c1fb867fa9	Update README.md	2017-07-23 17:22:01 +10:00
Ben V. Brown	2c5a83c134	Tiny patch for as mentioned in #30	2017-07-23 17:03:17 +10:00