Add support for Sequre S99, copied S60P settings

Makefile

@@ -52,7 +52,7 @@ DOCKER_CMD=$(DOCKER_BIN)  -f $(DOCKER_YML)  run  --rm  builder
 MKDOCS_YML=$(CURDIR)/scripts/IronOS-mkdocs.yml
 
 # supported models
-MODELS=TS100 TS80 TS80P Pinecil MHP30 Pinecilv2 S60 TS101 S60P # target names & dir names
+MODELS=TS100 TS80 TS80P Pinecil MHP30 Pinecilv2 S60 TS101 S60P S99 # target names & dir names
 MODELS_ML=Pinecil  Pinecilv2 # target names
 MODELS_MULTILANG=Pinecil_multi-lang  Pinecilv2_multi-lang # dir names
 

source/Core/BSP/Sequre_S60/Pins.h

@@ -69,5 +69,36 @@
 #define MOVEMENT_Pin       GPIO_PIN_3
 #define MOVEMENT_GPIO_Port GPIOA
 
+#endif
+
+#ifdef MODEL_S99
+
+#define KEY_B_Pin             GPIO_PIN_1
+#define KEY_B_GPIO_Port       GPIOB
+#define TMP36_INPUT_Pin       GPIO_PIN_5
+#define TMP36_INPUT_GPIO_Port GPIOA
+#define TMP36_ADC1_CHANNEL    ADC_CHANNEL_5
+#define TMP36_ADC2_CHANNEL    ADC_CHANNEL_5
+#define TIP_TEMP_Pin          GPIO_PIN_0
+#define TIP_TEMP_GPIO_Port    GPIOA
+#define TIP_TEMP_ADC1_CHANNEL ADC_CHANNEL_0
+#define TIP_TEMP_ADC2_CHANNEL ADC_CHANNEL_0
+#define VIN_Pin               GPIO_PIN_4
+#define VIN_GPIO_Port         GPIOA
+#define VIN_ADC1_CHANNEL      ADC_CHANNEL_4
+#define VIN_ADC2_CHANNEL      ADC_CHANNEL_4
+#define KEY_A_Pin             GPIO_PIN_0
+#define KEY_A_GPIO_Port       GPIOB
+#define PWM_Out_Pin           GPIO_PIN_8
+#define PWM_Out_GPIO_Port     GPIOB
+#define PWM_Out_CHANNEL       TIM_CHANNEL_3 // Timer 4; channel 3
+#define SCL2_Pin              GPIO_PIN_6
+#define SCL2_GPIO_Port        GPIOB
+#define SDA2_Pin              GPIO_PIN_7
+#define SDA2_GPIO_Port        GPIOB
+// Pin gets pulled high on movement
+#define MOVEMENT_Pin       GPIO_PIN_3
+#define MOVEMENT_GPIO_Port GPIOA
+
 #endif
 #endif /* BSP_MINIWARE_PINS_H_ */

source/Core/BSP/Sequre_S60/configuration.h

@@ -119,7 +119,7 @@
 // Vin_max = (3.3*(r1+r2))/(r2)
 // vdiv = (32768*4)/(vin_max*10)
 
-#if defined(MODEL_S60) + defined(MODEL_S60P) == 0
+#if defined(MODEL_S60) + defined(MODEL_S60P)+defined(MODEL_S99) == 0
 #error "No model defined!"
 #endif
 
@@ -197,6 +197,37 @@
 #define MODEL_HAS_DCDC // We dont have DC/DC but have reallly fast PWM that gets us roughly the same place
 #endif                 /* S60P */
 
+#ifdef MODEL_S99
+#define VOLTAGE_DIV        460 // Default divider scaler
+#define CALIBRATION_OFFSET 200 // Default adc offset in uV
+#define PID_POWER_LIMIT    70  // Sets the max pwm power limit
+#define POWER_LIMIT        0   // 0 watts default limit
+#define MAX_POWER_LIMIT    70
+#define POWER_LIMIT_STEPS  5
+#define OP_AMP_GAIN_STAGE  536
+#define TEMP_uV_LOOKUP_S60
+#define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate
+
+#define HARDWARE_MAX_WATTAGE_X10 600
+
+#define TIP_THERMAL_MASS    8   // X10 watts to raise 1 deg C in 1 second
+#define TIP_THERMAL_INERTIA 128 // We use a large inertia value to smooth out the drive to the tip since its stupidly sensitive
+
+#define TIP_RESISTANCE 20 //(actually 2.5 ish but we need to be more conservative on pwm'ing watt limit) x10 ohms
+
+#define OLED_128x32
+#define GPIO_VIBRATION
+#define POW_PD_EXT                2
+#define USB_PD_EPR_WATTAGE        0 /*No EPR*/
+#define DEBUG_POWER_MENU_BUTTON_B 1
+#define HAS_POWER_DEBUG_MENU
+#define TEMP_NTC
+#define I2C_SOFT_BUS_2 // For now we are doing software I2C to get around hardware chip issues
+#define OLED_I2CBB2
+
+#define MODEL_HAS_DCDC // We dont have DC/DC but have reallly fast PWM that gets us roughly the same place
+#endif                 /* S99 */
+
 #define FLASH_LOGOADDR      (0x08000000 + (62 * 1024))
 #define SETTINGS_START_PAGE (0x08000000 + (63 * 1024))
 

source/Core/Drivers/Font.h

@@ -141,7 +141,7 @@ const uint8_t disconnectedTip[] = {
     0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x37, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x38, 0x04, 0x04, 0x02, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
 #endif
 
-#if defined(MODEL_S60)+defined(MODEL_S60P) > 0
+#if defined(MODEL_S60)+defined(MODEL_S60P)+defined(MODEL_S99) > 0
 const uint8_t buttonA[] = {
     // width = 42
     // height = 16

source/build.sh

@@ -6,7 +6,7 @@ TRANSLATION_DIR="../Translations"
 # AVAILABLE_LANGUAGES will be calculating according to json files in $TRANSLATION_DIR
 AVAILABLE_LANGUAGES=()
 BUILD_LANGUAGES=()
-AVAILABLE_MODELS=("TS100" "TS80" "TS80P" "Pinecil" "MHP30" "Pinecilv2" "S60" "S60P" "TS101")
+AVAILABLE_MODELS=("TS100" "TS80" "TS80P" "Pinecil" "MHP30" "Pinecilv2" "S60" "S60P" "S99" "TS101")
 BUILD_MODELS=()
 
 builder_info() {