diff --git a/source/Core/BSP/Sequre/Pins.h b/source/Core/BSP/Sequre/Pins.h
index 24b65bb5..183c3700 100644
--- a/source/Core/BSP/Sequre/Pins.h
+++ b/source/Core/BSP/Sequre/Pins.h
@@ -69,5 +69,37 @@
 #define MOVEMENT_Pin       GPIO_PIN_3
 #define MOVEMENT_GPIO_Port GPIOA
 
-#endif
+#endif // MODEL_S60P
+
+#ifdef MODEL_T55
+
+#define KEY_B_Pin             GPIO_PIN_1
+#define KEY_B_GPIO_Port       GPIOB
+#define TMP36_INPUT_Pin       GPIO_PIN_5
+#define TMP36_INPUT_GPIO_Port GPIOA
+#define TMP36_ADC1_CHANNEL    ADC_CHANNEL_5
+#define TMP36_ADC2_CHANNEL    ADC_CHANNEL_5
+#define TIP_TEMP_Pin          GPIO_PIN_0
+#define TIP_TEMP_GPIO_Port    GPIOA
+#define TIP_TEMP_ADC1_CHANNEL ADC_CHANNEL_0
+#define TIP_TEMP_ADC2_CHANNEL ADC_CHANNEL_0
+#define VIN_Pin               GPIO_PIN_4
+#define VIN_GPIO_Port         GPIOA
+#define VIN_ADC1_CHANNEL      ADC_CHANNEL_4
+#define VIN_ADC2_CHANNEL      ADC_CHANNEL_4
+#define KEY_A_Pin             GPIO_PIN_0
+#define KEY_A_GPIO_Port       GPIOB
+#define PWM_Out_Pin           GPIO_PIN_8
+#define PWM_Out_GPIO_Port     GPIOB
+#define PWM_Out_CHANNEL       TIM_CHANNEL_3 // Timer 4; channel 3
+#define SCL2_Pin              GPIO_PIN_6
+#define SCL2_GPIO_Port        GPIOB
+#define SDA2_Pin              GPIO_PIN_7
+#define SDA2_GPIO_Port        GPIOB
+// Pin gets pulled high on movement
+#define MOVEMENT_Pin       GPIO_PIN_3
+#define MOVEMENT_GPIO_Port GPIOA
+
+#endif // MODEL_T55
+
 #endif /* BSP_MINIWARE_PINS_H_ */
diff --git a/source/Core/BSP/Sequre/configuration.h b/source/Core/BSP/Sequre/configuration.h
index e1e572f7..9a1cb770 100644
--- a/source/Core/BSP/Sequre/configuration.h
+++ b/source/Core/BSP/Sequre/configuration.h
@@ -120,7 +120,7 @@
 // Vin_max = (3.3*(r1+r2))/(r2)
 // vdiv = (32768*4)/(vin_max*10)
 
-#if defined(MODEL_S60) + defined(MODEL_S60P) == 0
+#if defined(MODEL_S60) + defined(MODEL_S60P) + defined(MODEL_T55) == 0
 #error "No model defined!"
 #endif
 
@@ -200,6 +200,43 @@
 #define MODEL_HAS_DCDC // We dont have DC/DC but have reallly fast PWM that gets us roughly the same place
 #endif                 /* S60P */
 
+#ifdef MODEL_T55
+// T55 Hotplate is similar to Project-Argon, PCB heater + PT100 sensor but no current rolloff compensation
+// Uses a HUB238 for PD negotiation like the S60P, also has a buzzer
+// Hold back left button for "DFU"
+
+#define VOLTAGE_DIV        460 // Default divider scaler
+#define CALIBRATION_OFFSET 200 // Default adc offset in uV
+#define PID_POWER_LIMIT    70  // Sets the max pwm power limit
+#define POWER_LIMIT        0   // 0 watts default limit
+#define MAX_POWER_LIMIT    70
+#define POWER_LIMIT_STEPS  5
+#define OP_AMP_GAIN_STAGE  536
+#define TEMP_uV_LOOKUP_PT100_1K_PULLUP
+#define USB_PD_VMAX       20 // Maximum voltage for PD to negotiate
+#define NO_DISPLAY_ROTATE    // Disable OLED rotation by accel
+
+#define HARDWARE_MAX_WATTAGE_X10 600
+
+#define TIP_THERMAL_MASS    10  // X10 watts to raise 1 deg C in 1 second
+#define TIP_THERMAL_INERTIA 128 // We use a large inertia value to smooth out the drive to the tip since its stupidly sensitive
+
+#define TIP_RESISTANCE 52 // PCB heater, measured at ~19C. Will shift by temp a decent amount
+
+#define OLED_128x32
+#define OLED_FLIP                 1 // Mounted upside down
+#define POW_PD_EXT                2
+#define USB_PD_EPR_WATTAGE        0 /*No EPR*/
+#define DEBUG_POWER_MENU_BUTTON_B 1
+#define HAS_POWER_DEBUG_MENU
+#define TEMP_NTC
+#define I2C_SOFT_BUS_2 // For now we are doing software I2C to get around hardware chip issues
+#define OLED_I2CBB2
+#define FILTER_DISPLAYED_TIP_TEMP 4 // Filtering for GUI display
+
+#define MODEL_HAS_DCDC // We dont have DC/DC but have reallly fast PWM that gets us roughly the same place
+#endif                 /* S60P */
+
 #define FLASH_LOGOADDR      (0x08000000 + (62 * 1024))
 #define SETTINGS_START_PAGE (0x08000000 + (63 * 1024))